Page 1
Smarthome.com, Inc. (800) SMART-HOME (949) 221-9200 http://smarthome.com Use: For Customer Enter below the Serial No. which is located on the rear or bottom of cabinet. Retain this information future reference. J X-S700 Model No.
Do not remove performance. not expose this appliance to rain or moisture. If you have any questions, consult your JVC dealer. ‘It may be unlawful to record or play back copyrighted material without the consent of the copyright owner. IMPORTANT ............3 APPLICABLE OPERATIONS FEATURES .
3. Malfunctions, etc. 1. Installation There are no user serviceable parts inside. Select a place which is level, dry and neither too If problems cord and -5°C and 4O”C/23”F occur, unplug the power hot nor too cold (between consult and 104°F). your dealer.
DESCRIPTION AND FUNCTIONS AV SELE i n d e x l a b e l s A t t a c h t h e p r o v i d e d corresponding to the c o m p o n e n t s connected to the input terminals to these sections.
Page 5
Pull the lid toward you to open the cover. DUAL OPERATE ON/OFF 4) button and AUDIO AUX ON/OFF button and indicator (7 - MONITOR indicator When pressed, the audio signal from the input P r e s s t h i s b u t t o n w h e n “ p a r a l l e l e d i t i n g ” source is replaced by the signal from the AUX input terminals on the rear panel (the indicator lights).
POWER button of Effective only when the corresponding SOURCE the JX-S700. SELECT indicator on the front panel is lit. When the component to be connected has a In “Dual Operate” mode, only the terminals of the...
P O W E R b u t t o n - KEY LOCK button SOURCE SELECT SOURCE SELECT buttons- MONITOR VIDEO MUTE button (*) L O O P P R O T E C T O N / O F F b u t t o n - DUAL OPERATE ON/OFF button MONITOR SELECT button (*) P R O C E S S O R O N / O F F b u t t o n -...
Connection To TV as follows: According to the type of monitor TV used, perform connections Monitor TV (with S-Video terminal) JX-S700 onnec on o a TV without S-Video Terminals ) Monitor TV JX-S700 Audio/Video connection cord Notes on connections: TV, set it to “S-Video”.
When the JX-S700 is used with a TV having no Video input terminal, an RF converter is required. Connect the MONITOR OUT terminals of the JX-S700 to the TV via the VCR. (In this case, the video program from the connected VCR cannot be monitored through the JX-S700.) Also, carefully read the instruction manual of the VCR.
Connection To VCRs (Connection to a VCR having SlVideo Terminals) JX-S700 Audio connection cord S-Video connection cord S-Video connection cord VCR with S-Video terminals (Connection to a VCR without S-Video Terminals] Using the audio/video connection cords, connect the VIDEO and AUDIO INPUT/OUTPUT terminals to the output and input terminals of the VCR, respectively.
Page 11
(with mono audio) (Connection to a Camcorder without S-Video T&minals ) Using the AV output cable provided with the camcorder, connect the INPUT terminals of the JX-S700 to the output terminals of the camcorder. When a camcorder with monaural audio is used: Connect the audio output terminal of the camcorder (with monaural audio) to the INPUT-3 “AUDIO L”...
The video program from the VCR selected by the SOURCE SELECT buttons can be viewed on the monitor TV. Color TV From MONITOR OUT To INPUT-l terminals Turn ON the power of the JX-S700 (the POWER Press the SOURCE SELECT-l button (the indicator of the JX-S700 lights). indicator of the JXS700 lights).
Page 13
Since the JX-S700 is equipped with Y/C-separator and Y/C mixer circuits, both S-Video and Video (composite) signals are supplied to the OUTPUT terminals, regardless of the type of signals input. If both S-Video and Video (composite) signals are input to the INPUT terminals of the JX-S700 at the same time, the S-Video signal has priority.
15. Preparation Press the SOURCE SELECT-3 button (the indicator of the JX-S700 lights). Turn ON the power of the JX-S700 and each component (the POWER indicators of the JX-S700 light). I ’ Start recording of the VCR(s), and start playback of the camcorder.
Page 15
Tips For Better Use About “Key Lock” mode: While the recording VCR is being operated, by pressing the KEY LOCK button on the JX-S700 will lock the key operation and thus effectively prevent mis-operation. When in Key Lock mode, only the MONITOR SELECT, MONITOR VIDEO MUTE and KEY LOCK buttons are effective.
Operate the Video Titler as required. Press the SOURCE SELECT-l button (the indicator of the JX-S700 lights). WINTER HOLIDAY Press the PROCESSOR “AUDIO” and “VIDEO” buttons (the indicators of the JX-S700 light). Start recording with the recording VCR. AUDIO VIDEO Recording VCR...
Page 17
Also, carefully read the instruction manuals of each component. Since the built-in Y/C separator and Y/C mixer circuits are not applied to the PROCESSOR OUT terminals of the JX-S700 (but effective for signal input to the PROCESSOR IN terminals), connect the AV processor in the following manner:...
AUX terminals Preparation Camcorder Preparation Press the AUX ON/OFF button (the AUDIO AUX indicator of the JX-S700 lights). Turn ON the power of each component (the POWER indicator of the JX-S700 light). Start the CD player and the recording VCR.
Page 19
ON/OFF is possible even during Key Lock mode. Notes on operatlon: When the Dual Operation is used, audio insertion is possible only for the Line-A components. button again (the AUDIO AUX indicator of the JX-S700 goes off.) Smarthome.com, Inc. (800) SMART-HOME (949) 221-9200 http://smarthome.com...
JX-S700 lights]. indicator of the JXS700 light). Press the DUAL OPERATE button (the indicator Start the playback VCR @ and the recording VCR of the JX-S700 lights) [check that the indicator is green] VCR @ for playback VCR @I for recording OPERATE Lights in green.
Page 21
Preparation Press the MONITOR SELECT button (the Cautions on parallel editing indicator on the front panel of the JX-S700 Although any source is available as an input for changes from green to yellow). Line-A, the input/output sources for Line-B are...
Separator circuit) The JX-S700 incorporates a Y/C separator circuit which splits composite video signal input to the VIDEO input terminal into Y (luminance) and C (chrominance) signals. This is convenient when editing from VCRs without S-Video terminals to VCRs with S-Video terminals, or when a TV with S-Video input terminals is used as the monitor.
Page 23
Use the POWER INITIAL switch when the JX-S700 is used with a timer. Major function of POWER INITIAL switch The input source that is selected when the JX-S700 is turned ON by the timer can be specified beforehand, <Switch position>...
I lluul3Ltalluu What appears to be a malfunction may not always be serious. Make sure first... Remedy Symptom No power the power cord disconnected from the Plug the power cord firmly into the AC wall AC outlet? outlet. Is the POWER button turned OFF? Press the POWER button to ON.
Need help?
Do you have a question about the JX-S700 and is the answer not in the manual?
Questions and answers