Summary of Contents for Hitech PWS Series
- Page 1 Supplement D PLC Workstation PWS3000/3100 PLC WORKSTATION APPLICATION MANUAL Revision C, November 1998 Hitech Electronics Corporation 4th Fl. No. 501-15 Chung-Cheng Rd., Shin-Tien Taipei Shien, Taiwan, R.O.C. Tel:886-2-22183600 Fax:886-2-22183060...
- Page 2 10g, 11ms three times in each direction of X, Y, and Z axes RF Emissions CISPR 22, Class A Electrostatic Discharge IEC 801-2 Level 3 RF Susceptibility IEC 801-3 Level 2 High Frequence Transients IEC 801-4 Level 2 Hitech Electronics Corp.
- Page 3 Supplement D PLC Workstation Weight 2.9 Kg 2.9 Kg 3.2 Kg Cooling Natural cooling...
- Page 4 Mount the PWS to the preserved hole from the front side. Attach the mounting brackets from behind, and fasten the screw of the brackets with a screwdriver. Don't tighten the screws with too much force or it may cause a damage of the panel. Hitech Electronics Corp.
- Page 5 Supplement D PLC Workstation D.3.1 Dimensions of PWS31xx D.3.2 Torque Specifications After placing the Workstation in the cutout, you should tighten each nut to 0.07 newton- meters (10 inch/pounds) of torque. If you don't have a torque wrench, then try to tighten the nuts to compress the gasket to about 50% of its original thickness.
- Page 6 80x60 touch keys for PWS3100. For each changeable Object of a screen, the Compile function of ADP3 automatically groups those touch switches that the display area of the Object covers to form a touch key for the selection purpose. Hitech Electronics Corp.
- Page 7 Supplement D PLC Workstation When you press a touch key, the Workstation responds by sounding the buzzer for 200 milli-seconds (default) and reversing the color of that touch key for 200 milli-seconds. With the feedback, you know the Workstation accepts your key-press.
- Page 8 Press Calibrate button on the System Menu. The Select Item box appears. Press Touch Panel button on the Select Item box. A white dot appears on the upper-left corner of the screen and the message "Pin-point the white dot on the upper-left corner” appears. Hitech Electronics Corp.
- Page 9 Supplement D PLC Workstation Use a pencil that is not sharp or anything that is soft and suitable to pin-point the white dot on the screen. small moves lower-left corner screen and the message changes to "Pin-point the white dot on the lower-left corner.” Do not use anything that is made of metal or is sharp, such as a screw driver or ball pen to pin-point the touch panel.
- Page 10 "Battery check” in the Configuration Table. PWS-3100 Series PLC Workstation ROM BIOS Version 1.4 (C) 1997 Hitech Electronics Corporation Display Type ......Color TFT Display System RAM Size ...... 128 Kbytes Video RAM Size ....... 512 Kbytes Firmware Memory Size ....
- Page 11 Supplement D PLC Workstation If you have never configured your Workstation, the self-test may report a failure of the real time clock. If this happens, configure as described in section D.10. If you have never downloaded an application to the Workstation, the self-test may report a problem in the flash chips.
- Page 12 Allows you to download recipes to the Workstation from a PC or another Workstation. Upload Recipes Allows you to upload the recipes saved in the Workstation to a PC. Copy Recipes Allows you to copy recipes saved in the Workstation to another Workstation. D-11 Hitech Electronics Corp.
- Page 13 Supplement D PLC Workstation Exit Starts from the self-test again. D-12...
- Page 14 PWS-COM2 PC COM RS232C PC's 9-pin connector 25-pin female --CABLE---25-pin female PWS to PC's 25-pin connector PWS-COM2 PC COM RS232C 25-pin female --CABLE--- 9-pin female Warning: avoid electric shock, be sure to switch off D-13 Hitech Electronics Corp.
- Page 15 Supplement D PLC Workstation the power when connecting the communication/download cable to the PWS unit . D-14...
- Page 16 Communication Parameters dialog box, click Communications button in Workstation Setup dialog box. The Communication Parameter dialog appears with following options: The Workstation uses these parameters for PLC communications, if the DIP D-15 Hitech Electronics Corp.
- Page 17 Supplement D PLC Workstation . If parameters set in the switch No.5 is off DIP switch 5 is on, the Configuration Table will be used for PLC communications D-16...
- Page 18 Select Enabled if you want the synchronization function to be enabled. The default setting is Disabled. Baud rate Select 4800, 9600, or 19200 baud to specify the baud rate for communications between the Workstation and the PLC. The default setting is 9600. D-17 Hitech Electronics Corp.
- Page 19 Supplement D PLC Workstation Parameter Description Parity Select the parity of the communications between the Workstation and the PLC. Your choices are None, Odd, or Even. The default setting is None. If you set "Parity" to None, then you cannot set "Data size"...
- Page 20 * These pins have no functions on the PWS-3100 and new model PWS-3700. COM2 to RS-422 COM2 25-pin Female RS-422 Port TXD+ 14 RXD+ TXD- 15 RXD- RXD+ 16 TXD+ RXD+Term.21 RXD- 17 TXD- RTS+ 23 CTS+ 12 RTS- 24 CTS- 13 D-19 Hitech Electronics Corp.
- Page 21 Supplement D PLC Workstation D.11.1 Serial Communication Port1 (COM1) COM1 is a serial port which supports RS-232 and RS-422 operation. The PWS-3700 supports RS-485 operation also. The pin assignments of the port are listed below. See section D.9/D.11 for the examples of connections. D-20...
- Page 22 Output D6 - data bit 6 Output D7 - data bit 7 Input Acknowledge Not Input Busy Input Paper Empty Input Printer Selected Output Auto-feed Input Error Not Output Reset Not Output Select 18-25 Signal ground D-21 Hitech Electronics Corp.
- Page 23 Supplement D PLC Workstation D.12 Entering Password After the self-test, if the DIP switch No.6 is on, the Workstation displays a keypad to prompt you to enter a password; if DIP switch No.6 is off, the Workstation doesn't ask you to enter a password and the default user level is 1 after the power-on self-test if the DIP switch SW8 is set to on;...
- Page 24 About PWS3000/3100 To abandon the current change, select another field to exit the current selection. D-23 Hitech Electronics Corp.
- Page 25 Supplement D PLC Workstation To save all changes that you made to the password table, press [Save & Quit]. To abandon all changes, press [Quit]. Figure D-4 Numeric keys for password table Figure D-5 Reentering a password D.12.3 Reentering a Password When the Workstation is running the user application, you can enter a password to change the current user level by pressing an Action button that is assigned the function of...
- Page 26 “Contrast Down”. To save the setting, press an Action button which assigned function “Save Contrast”. user calibrate contrast pressing the "Calibrate" button on System Menu as well. The Workstation displays Select item as shown below. D-25 Hitech Electronics Corp.
- Page 27 Supplement D PLC Workstation D-26...
Need help?
Do you have a question about the PWS Series and is the answer not in the manual?
Questions and answers