Summary of Contents for Electron Charger EC-EVC-L2-11 KW-NN-G2
- Page 1 .arger Electric Vehicle AC Charger Installation Manual For model: EC-EVC-L2-11 KW-NN-G2/G3...
-
Page 2: Table Of Contents
/'liJectron' · �harger CONTENTS ..............1. Safety Instructions ... 1 1.1. Warnings & Cautions ................1 1.2. Installation Requirements ..............2 1.3. Daily Maintenance ................2 2. Product Introduction ..............4 2.1. Basic Interface ..................4 2.2. Basic Dimension ................. 5 2.3. -
Page 3: Safety Instructions
/'liJectron' · �harger WARNING EC-EVC-L2-11KW-NN-G2/G3 Safety Instructions 1.1. Warninas & Cautions WARNING To avofd fire, injury or death, read and follow the instructions carefully during installation, operation and maintenance. put fingers into the electric vehicle connector. DO NOT use this product if the power cord or EV cable is frayed, insula1ion DO NOT broken, or any other signs of damage. -
Page 4: Installation Requirements
/'liJectron' · �harger WARNING EC-EVC-L2-11KW-NN-G2/G3 1.2. Installation Requirements WARNING Disconnect electrical power prior to installing the charging station . Be sure to p review the user manual and ensure local building and electrical codes are reviewed before installing the AC charger. The AC charger should be installed by a qualified technician according to the user manual and local safety regulations. - Page 5 /'liJectron' · �harger EC-EVC-L2-11KW-NN-G2/G3 WARNING is damaged, please contact a professional technician. Avoid placing the charger near hot objects and at high temperature locations and away from dangerous substances such as flammable gases and corrosive materials. To avoid any danger, please do not put any heavy objects on the charger. For 48 Amp installations, we recommend not using a NEMA cable.
-
Page 6: Product Introduction
/'liJectron' · �harger INTRODUCTION EC-EVC-L2-11KW-NN-G2/G3 P ' r oduct Introduction Avoid placing the charger near hot objects or high CAUTION: temperature locations and away fmm dangerous substances such as fl ammable gases and corrosive materials . 2.1. I Basic Inte 1 rface 1------- Mounting Hole LAN Cable Inlet-... -
Page 7: Basic Dimension
/'liJectron' · �harger EC-EVC-L2-11 KW-NN-G2/G3 INTRODUCTION 2.2. Basic Dimension ENCLOSURE ;._ 190 --------- 7.48" -------------•---------------- � ---- 12.99" ff��� ll'lm 12.99" Front View Left View 190 m m -------' /1.48" Bottom View www.ElectronCharger.com... -
Page 8: Specifications
/'liJectron' · �harger INTRODUCTION EC-EVC-L2-11 KW-NN-G2/G3 2.3. Specifications Model Name EC-EVC-L2-11KW-NN-G2/G3 Input AC Rating 208-240Vac Max. AC Current Power 8A·48A Specif ication Frequency 60Hz Max. Output Power 11.SkWMAX Display 2.5" Digital Screen User Authentication User Interface RFID(ISO/IEC 14443 A/B), APP &... -
Page 9: Design Standards
/'liJectron' · �harger EC-EVC-L2-11 KW-NN-G2/G3 INTRODUCTION 2.4. Design Standards UL 2594: Electric Vehicle Supply Equipment. UL 2231-1: UL Prersonnel Protection System s for Electric Vehicle (EV) Supply Circuits:General Requirements. UL 2231: Personnel Protection Systems for Electric Vehicle (EV) Supply Circuits: Particular Requirements for Protection Devices for Use in Charging Systems. -
Page 10: Accessories
CNl'Cff Millhlil /'liJectron' · �harger ACCESSORIES EC-EVC-L2-11 KW-NN-G2/G3 Accessories Check the box to ensure you have this installation guide and these parts: Vffltele ELectnc OA.ccharger Manual Template &user 9,crewCover G'v1ounting M6 Expansion &standard RFID Screws*2 Cards*2 Product Name Quantity... -
Page 11: Tools For Mounting
/'liJectron' · �harger EC-EVC-L2-11 KW-NN-G2/G3 MOUNTING Tools for Mounting Tools required before installing the Wall-mounted charger, gather the following tools: ewire stripper Phillips screwdriver Drill 0Level Pencil C,Adjustable or marker wrench NOTE: The above tools are very important, get them ready prior to installation. -
Page 12: Plan For Mounting
/'liJectron' · �harger MOUNTING EC-EVC-L2-11 KW-NN-G2/G3 Plan for Mounting WARNING: In areas with frequent thunderstorms, add surge protection at the service panel for all circuits. Ensure all power and ground connections, especially those at the breaker and bus bar, are clean and tight. - Page 13 /'liJectron' · �harger EC-EVC-L2-11 KW-NN-G2/G3 MOUNTING ►ii!M Nail #5 two expansion rubber sleeves into the holes and nail #5 one screw to the top expansion rubber sleeves. The distance between the cover of the screw and the wall is about 5mm.
- Page 14 /'liJectron' · �harger MOUNTING EC-EVC-L2-11 KW-N N-G2/G3 ►ii ➔ Wire the Circuit WARNING This device must be grounded. Disconnect electrical power prior to installing the charging station. Improper connection of the equipment-grounding conductor would result in a risk of electric shock. Check with a qualified electrician or service man you are not sure whether the product is properly grounded.
- Page 15 /'liJectron' · �harger EC-EVC-L2-11 KW-NN-G2/G3 MOUNTING ►iHII Overall outlook after installation www.ElectronCharger.com...
-
Page 16: Perate Your Device
/'liJectron' · �harger OPERATE EC-EVC-L2-11 KW-NN-G2/G3 6. Operate Your Device WARNING This device should be supervised when used around children. CAUTION Please use the charger properly. Do not hit or press hard on the enclosure. If the case is damaged, please contact a professional technician. - Page 17 /'liJectron' · �harger EC-EVC-L2-11 KW-NN-G2/G3 OPERATE ►ihiii Plug the Charging Connect or: Please plug the charging connector into the vehicle charging inlet. ►iHM CHARGING: When the charging is going on, "Charging, circularly voltage, You can see currents and kWh." in the LED Screen.
-
Page 18: Operating Steps With Rfid Card
/'liJectron' · �harger OPERATE EC-EVC-L2-11 KW-NN -G2/G3 6.2. Operating Steps with RFID Card ..CAUTION: Avoid placing the charger near hot objects and at high temperature locations and away from dangerous substances such as flammable gases and corrosive materials . ►iHII Standby Mode: After the power has been turned Plc:uc... - Page 19 /'liJectron' · �harger EC-EVC-L2-11 KW-NN-G2/G3 OPERATE ►ii!M Tap the standard RFID to start/stop charging. •Figures are for reference only ►iiill CHARGING: When the charging is going on, You can see "Charging, circularly voltage, , , ., currents and kWh." in the LED Screen.
-
Page 20: Light Codes
/'liJectron' · �harger EC-EVC-L2-11 KW-NN -G2/G3 WARNING Light Codes 7.1. The Details of Screen Charging Charging Message Scan QR Code Or Tag Card 7.2. Error and Warning Messages Status Screen Display Remark Off Ground Auto Recover 0001 RCD Abnormal Auto Recover 0002 Over Current Protection Auto Recover... -
Page 21: Fcc Statement
/'liJectron' · �harger WARNING EC-EVC-L2-11KW-NN-G2/G3 FCC STATEMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation. -
Page 22: Warranty And Maintenance
/'liJectron' · �harger EC-EVC-L2-11KW-NN-G2/G3 WARNING 9. Warranty and Maintenance The warranty period for this charger is two years. During the warranty period for any malfunction under normal use according to the User Manual and Service Instructions (to be determined by certified maintenance technicians of sellers), the product shall be repaired free of charge.
Need help?
Do you have a question about the EC-EVC-L2-11 KW-NN-G2 and is the answer not in the manual?
Questions and answers