Related Manuals for Intelligent Design X-Scrub 16
Summary of Contents for Intelligent Design X-Scrub 16
- Page 1 User Manual X-Scrub 16 1620S. Friendswood Dr. #143, Friendswood, TX 77546 IntelligentDesignMFG.com • Tel:1-833-554-3628...
-
Page 2: Introduction
Introduction This manual provides necessary machine operation and maintenance instructions. Please read and understand this manual carefully before operating or using this machine. When ordering replacement parts, refer to the spare parts manual that came with this machine. Before selecting parts or accessories, please confirm your machine model and serial number. -
Page 3: Table Of Contents
Terminology Reference - 16” X-Scrub page 9 Troubleshooting page 10 Technical Parameters page 11 Circuit Diagram of X-Scrub 16 Battery Scrubber page 13 Exploded View of Handle page 14 Exploded View of Water Tank page 16 Exploded View of Frame... -
Page 4: Important Safety Instructions
IMPORTANT SAFETY INSTRUCTIONS • Operators must read and fully understand this manual before operating or maintaining this machine. • This machine is suitable for industrial and commercial for cleaning indoor hard surface flooring. • Do not operate this machine in flammable or explosive areas which includes flammable liquids, gases or flammable dust. -
Page 5: Transporting And Unpacking The Machine
TRANSPORTING THE MACHINE • Make sure the machine is stopped on a level surface. • Make sure the machine is turned off. • Wear proper PPE when performing repairs or maintenance. • Wear protective eye wear and gloves when handling batteries, battery wiring or any chemical/water left in the machine. -
Page 6: Brush And Pad Options
BRUSH AND PAD SELECTION OPTIONS To ensure the best cleaning performance, please select the correct brush or pad for your type of fl ooring. Please refer to the fl oor manufacturer to ensure you are using the correct pad or brush. Below are the basic options for daily cleaning: Standard Brush •... -
Page 7: Loading Pads On The Pad Driver
LOADING PADS TO THE PAD HOLDER To load pads to the pad holder, remove the pad holder from the machine and remove the centering device, place the pad on the pad holder and screw on the centering device tight. Make sure the centering device is tightly fastened and cupped into the pad. -
Page 8: Check List - Before Operation
CHECK THE FOLLOWING BEFORE OPERATION: • Dust mop or sweep the floor of dry debris. • Check to make sure the correct cleaning pad or brush is installed and is not worn past its life span. • Check to make sure the machine has been charged. •... -
Page 9: Terminology Reference - 16" X-Scrub
X-Scrub 16 TERMINOLOGY REFERENCE Description Handle Brush/Water activation lever Lever to adjust handle height Dirty water tank cover Dirty water tank Clean water fill inlet Clean water tank Scrub deck Front bumper and support wheel Squeegee assembly Rear wheel Main on/off switch... -
Page 10: Troubleshooting
Troubleshooting Problem Problem Solution The battery is out of power. Charge the battery. Battery failure. Charge the battery. The machine does not work. Loose battery connection. Tighten the battery cables. The main fuse is blown. Replace the fuse. The brush lever is not working. Press the safety lock then lever. -
Page 11: Technical Parameters
Technical Parameters Item Unit X-Scrub ® Brush Inches Estimated cleaning produc- square feet up to 22,000 per hour tivity Squeegee width Inches Estimated run time Hours Pad holder Inches Clean water tank Gallons Recovery tank Gallons Brush motor Watt Vacuum motor Watt Battery Volt... -
Page 13: Circuit Diagram Of X-Scrub 16 Battery Scrubber
Circuit Diagram of X-Scrub 16 Battery Scrubber K1 Circular Switch KM1/KM2 24V Intermediate Relay K2/K3 Rocker switch D1 Brush Plate Motor D2 Water Suction Motor YV Solenoid valve Fu1 60A fuse Fu2 30A fuse Fu3 3A fuse LCElectric quantity display board... -
Page 14: Exploded View Of Handle
Exploded View of Handle... - Page 15 Washer idm X-Scrub 16 handle 12 190000111 190000130 Yoke idm X-Scrub 16 handle adjustment Gear idm X-Scrub 16 handle 13 190000112 Handle idm X-Scrub 16 rear 190000131 adjustment Switch idm X-Scrub 16 brush Screw idm X-Scrub 16 handle 14 190000113...
-
Page 16: Exploded View Of Water Tank
Exploded View of Water Tank... - Page 17 Tube idm X-Scrub 16 silicone 190000152 190000166 for vac motor m6 8x12 Washer idm X-Scrub 16 for 190000153 190000167 Ribbon idm X-Scrub 16 vac motor Shock absorber idm X-Scrub 190000154 16 vac motor 190000155 Clamp idm X-Scrub 16 cable 1...
-
Page 18: Exploded View Of Frame
Exploded View of Frame... - Page 19 FUSE HOLDER IDM X-Scrub NUT IDM X-Scrub 16 FRONT 190000186 190000208 16 60 AMP CASTER BOLT IDM X-Scrub 16 190000187 FUSE IDM X-Scrub 16 30A 190000209 FRONT CASTER SCREW IDM X-Scrub 16 190000188 FUSE IDM X-Scrub 16 60A 190000210 SOLUTION BRACKET SIDE...
-
Page 20: Exploded View Of Brush Plate And Squeegee
Exploded View of Brush Plate and Squeegee... - Page 21 Weldement idm X-Scrub 16 190000290 Motor idm X-Scrub 16 brush 190000256 squeegee lift 1-1 190000230 Spacer idm X-Scrub 16 brush motor 1 190000257 Bracket idm X-Scrub 16 squeegee 2 190000231 Hub idm X-Scrub 16 brush upper 190000258 Bolt idm X-Scrub 16...
- Page 22 Maintenance Record...
- Page 23 Maintenance Record...
- Page 24 rev 0724...
Need help?
Do you have a question about the X-Scrub 16 and is the answer not in the manual?
Questions and answers