Table of Contents
Advertisement
Quick Links
TTE GPRS Simple
GSM/GPRS Communication Module
• Installation and Programming Manual
• Operation Instruction
• User Guide
Attention:
This manual contains information on limitations regarding product use and
function and information on the limitations as to liability of the manufacturer.
The entire manual should be carefully read.
The information in this manual is a subject to change without notice!
Rev. 9.5.x
Release 12/2019
Advertisement
Table of Contents
Summary of Contents for Teletek electronics TTE GPRS Simple
- Page 1 TTE GPRS Simple GSM/GPRS Communication Module • Installation and Programming Manual • Operation Instruction • User Guide Attention: This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer.
-
Page 2: Table Of Contents
TTE GPRS Simple Communication Module – Installation and Programming Manual Table of contents 1. INTRODUCTION ........................4 1.1 General Information ........................4 1.1.1 Functional Features ........................ 4 1.1.2 Technical Specifications......................4 1.1.3 Operation Block Diagram ....................... 5 1.2 Before you start ..........................6 1.3 TTE GPRS Simple Models ....................... - Page 3 TTE GPRS Simple Communication Module – Installation and Programming Manual 6.5 Remote Resetting of TTE GPRS Simple ..................43 6.6 Checking the Signal Strength ....................... 43 DOCUMENTATION FEEDBACK If you have any comments or suggestions on our products’ manuals or installation instructions you can email us on: info@teletek-electronics.bg...
-
Page 4: Introduction
(SB-U) suitable for wall mounting according the application. Optional, TTE GPRS Simple provides also voice reporting and voice guiding to the end user when it is additionally equipped with micro SD Card with recorded voice messages. -
Page 5: Operation Block Diagram
1. Serial communication between Eclipse series Burglary Alarm Control Panel and TTE GPRS Simple module. The TTE GPRS Simple communication module is mounted into the panel’s box and is connected via serial interface flat cable to the control panel’s PCB – see item 2.1 Serial Connection. -
Page 6: Before You Start
- at least 100 minutes per month (it depends on the frequency of use). - To be able to use the voice reporting and voice management options, your TTE GPRS Simple must be equipped with SD micro card with recorded messages. -
Page 7: Hardware Installation
Serial terminal of the Eclipse control panel PCB. The TTE GPRS Simple is mounted into the panel’s installation box and is powered on directly from the control panel via the serial interface. The serial connection between the module and control panel is done with a flexible flat cable 300mm long, included in the supplied equipment. -
Page 8: Basic Installation Steps
4. Switch off the PIN protection code of the SIM card and place it into the SIM interface holder of the TTE GPRS Simple module. 5. For TTE GPRS Simple VG (Model: Voice Guide), check the micro SD card to be placed into the card holder. -
Page 9: Restore To Factory Settings
TTE GPRS Simple Communication Module – Installation and Programming Manual The LED Indication has the following meaning: Action Colour Description Green The module is in normal operation mode. • Possible trouble with the SIM card: 1. The SIM card is missing. -
Page 10: Programming With Proste
Run the ProsTE software and choose in sequence using the right mouse button: System – Add – TTE GPRS Simple. The TTE GPRS Simple menus are loaded at the left side as a tree structure. Select the module and using the right mouse button again choose in sequence: TTE GPRS Simple – Read. -
Page 11: General Settings Menu
3.2 General Settings Menu Click on the “+” icon in front of TTE GPRS Simple module to expand the programming main menus. Select General Settings menu. The possible settings are displayed on the right side on the screen: Important Note. - Page 12 “Stand Alone/None” – Not used. o “CA62” – Set this option if the TTE GPRS Simple is connected* to CA62 control panel. o “Eclipse” – Set this option if the TTE GPRS Simple is connected* to Eclipse series control panel.
-
Page 13: Phones Menu
Phone Number”; 2 to “2. Phone Number”, etc. Select the check boxes for those phone numbers, which are going to be used for Reporting. * Note: The Voice messages receiving, requires your TTE GPRS Simple to be equipped with a micro SD card with recorded voice messages from manufacturer. - Page 14 6.3.2 Voice Management Mode – Operation Algorithm. * Note: The Voice management mode, requires your TTE GPRS Simple to be equipped with a micro SD card with recorded voice messages from manufacturer. Example: The Phone numbers 1, 2 and 3 are enabled for Voice Management. The numbers 1, 2 and 3 are selected.
-
Page 15: Phone Number Submenus
Important note: The priority of dialing of the set phone numbers starts with Phone number 1 (set in submenu “1. Phone Number”), Phone number 2 (set in submenu “2. Phone Number”), etc. The TTE GPRS Simple first will send the SMS messages and then will proceed with calls for playing the voice messages for events. -
Page 16: Using "Apply Selected" Button
TTE GPRS Simple Communication Module – Installation and Programming Manual prefix for the country, for example “+359”, no blank spaces or special symbols between numbers are allowed. • “Messaging” – Set the type of Reporting: SMS or Voice. o “SMS” – To the set phone number will be sent SMS messages for event. -
Page 17: Mobile Operators Menu
In the fields must be set some specific information for the mobile service provider. These fields will be filled in automatically after the registration of Eclipse panel with TTE GPRS Simple module to a User account at AJAX WEB – the user sets the mobile service provider according the selected country. -
Page 18: Receiver Settings Menu
“Main Receiver Port” – The Port of the Main Receiver server for monitoring. o “Encryption Key 1” – A special security encrypted key for the connection. The key is 32-symbols long and must be set one and the same at the TTE GPRS Simple and the server for monitoring for proper operation. -
Page 19: Saving A Tdf File
TTE GPRS Simple module configuration. 3.7 Writing a Configuration To upload the settings from ProsTE to the TTE GPRS Simple module you have to write them to the currently connected module. Select TTE GPRS Simple main menu and choose in sequence using the right mouse button: TTE GPRS Simple –... -
Page 20: Ajax Web User Interface
* Note: All previewed examples and screens below are based on this web application. 4.1 Creating an Account To be able to control your Eclipse burglary alarm system via TTE GPRS Simple communication module, first you must have a User account registered to AJAX WEB User Interface (hereafter referred to as AJAX WEB). -
Page 21: Adding A System To Account
TTE GPRS Simple Communication Module – Installation and Programming Manual Attention: It is important to enter a valid e-mail address, so to be able to complete the registration and to receive in the future the information for the registered systems to your account at AJAX WEB. - Page 22 TTE GPRS Simple Communication Module – Installation and Programming Manual In case of serial connection between Eclipse panel and TTE GPRS Simple module you have to make the following settings: - “System Name” – Enter a name describing the protected site. The name can be edited or changed later.
-
Page 23: Online Connection With Ajax Sp Pro Server
Receiver Settings menus. There will be available the automatically set parameters from the server. You can edit some of them if necessary. Select in sequence using the right mouse button TTE GPRS Simple – Write to upload the settings into the module. Follow the steps as described in item 3.7 Writing a... -
Page 24: Operation With System
TTE GPRS Simple Communication Module – Installation and Programming Manual 4.4 Operation with System The User can perform some operation with the systems added to his account. “Search Filter” – On the top of the System List section, the User can search among the •... - Page 25 TTE GPRS Simple Communication Module – Installation and Programming Manual o “Red Dot Notifications” – A special mark (a red dot) alerts the User in case of occurring of an event (in the system list of MobileTTE). Check the boxes of those events for which you want to be alerted.
-
Page 26: Tte Gprs Simple - Installation Summary
• Disable the PIN protection code of the SIM card for the module and place it in the holder. For TTE GPRS Simple VG (Model: Voice Guide) check the micro SD card to be placed into the SD card holder. -
Page 27: User Guide
TTE GPRS Simple Communication Module – Installation and Programming Manual 6. USER GUIDE 6.1 AJAX WEB User Interface Using AJAX WEB interface, the user can perform remotely the following activities with his security system via the TTE GPRS Simple module: - review the current status of the areas, troubles and the memory log of the control panel connected to TTE GPRS Simple module;... -
Page 28: System Status
Not available Available Menus* * Note: The “Communication module” menu for TTE GPRS Simple is available for selection but it will be empty, because no PGMs outputs are present in this module. To exit from the system press “Disconnect” button. - Page 29 TTE GPRS Simple Communication Module – Installation and Programming Manual In Section 1, the user can review the technical troubles: Trouble Description AC Loss The mains power supply is lost. Battery Low The accumulator battery is discharged or missing. Blown Fuse Blown out fuse on the control panel.
-
Page 30: Zones Control Panel Submenu
TTE GPRS Simple Communication Module – Installation and Programming Manual In Section 3, at the bottom of the page, the User can update the time and date of the control panel. To set the Date, press on the calendar icon and choose the “Today:…” option. To set the time [HH:MM], enter the current time into the next field. -
Page 31: Control Panel Pgms Submenu
TTE GPRS Simple Communication Module – Installation and Programming Manual Control Panel PGMs Submenu To review the available PGMs in your Eclipse panel, press “Control Panel PGMs” tab in System Status menu. The available PGMs for control depend on the settings programmed in your Eclipse security system. -
Page 32: Ip Cameras Submenu
TTE GPRS Simple Communication Module – Installation and Programming Manual IP Cameras Submenu This a special menu for attaching IP cameras for video surveillance to security zones in the protected site. The IP cameras must support operation via RTSP communication protocol. This is an opportunity for the user to watch a live video from the site directly via AJAX WEB without using other video application software for monitoring. -
Page 33: View Events
TTE GPRS Simple Communication Module – Installation and Programming Manual All added video devices are presented in a list in IP Cams menu with their online status: Icon Description The IP camera is offline. No video streaming is available. The IP camera is online. The User can watch the live video streaming in “Zones” menu. -
Page 34: Mobile Tte Smartphone Application
Mobile TTE is a smart phone application suitable for remote management of burglary control panels and modules produced by Teletek Electronics JSC. The application is compatible with Android and iOS platforms and can be downloaded directly from Google Play and App Store, or you can use the QR... -
Page 35: Connection To A System
TTE GPRS Simple Communication Module – Installation and Programming Manual 6.2.2 Connection to a System To connect with the system, press the button and wait until the connection is established. When you are connecting to a system for the first time you will be asked to enter your valid user code for operation with Eclipse panel. -
Page 36: Controlling Of Control Panel
TTE GPRS Simple Communication Module – Installation and Programming Manual 6.2.4 Controlling of Control Panel PGMs Press Outputs menu. Via MobileTTE the user can review and control only the enabled for remote control PGM outputs for the Eclipse panel. The outputs are presented with their names set in AJAX WEB with description “Panel”. - Page 37 TTE GPRS Simple Communication Module – Installation and Programming Manual The general functions of MobileTTE is to provide to the user remote control of his Eclipse control panel and to receive notification messages in case of alarm or trouble events and the arming status of the system.
- Page 38 TTE GPRS Simple Communication Module – Installation and Programming Manual The notifications have the following description: Event Description Sound type ALARM Notification in case of burglary alarm in the system. Special alarm tone* Notification in case of arming (Full, Stay, Sleep) and disarming.
- Page 39 TTE GPRS Simple Communication Module – Installation and Programming Manual Move down to the bottom of Settings menu. There are options for setting the date and time of your control panel and to select different language of your MobileTTE smartphone application.
-
Page 40: Voice Management
The micro SD card is included in the kit of TTE GPRS Simple VG (Model: Voice Guide). 6.3.1 Receiving of Voice messages for Events In case of alarm or trouble event in the system, the TTE GPRS Simple will dial the entered phone numbers with set Messaging option “Voice” (see 3.3.1 Phone Number... -
Page 41: Voice Management Mode - Operation Algorithm
TTE GPRS Simple Communication Module – Installation and Programming Manual 6.3.2 Voice Management Mode – Operation Algorithm... -
Page 42: Sms Messages For Events
Area 3 (C). 6.4 SMS Messages for Events In case of alarm or trouble event in the system, the TTE GPRS Simple will send SMS messages to those phone numbers with set Messaging option “SMS” (see 3.3.1 Phone Number Submenus). - Page 43 TTE GPRS Simple Communication Module – Installation and Programming Manual 6.5 Remote Resetting of TTE GPRS Simple This is an option for remote resetting of the module via SMS command. To perform Restart of the module, send an SMS to it with text “Reset” or “Restart”. The module will confirm the received command with message “Module will restart after 10 seconds”.
- Page 44 TTE GPRS Simple Communication Module – Installation and Programming Manual www.teletek-electronics.com Address: Bulgaria, 1407 Sofia, 14А Srebarna Str. Tel.: +359 2 9694 800, Fax: +359 2 962 52 13 e-mail: info@teletek-electronics.bg...
Need help?
Do you have a question about the TTE GPRS Simple and is the answer not in the manual?
Questions and answers