BenQ W1060 User Manual
  1. Manuals
  2. Brands
  3. BenQ Manuals
  4. Projector
  5. W1060
  6. User manual

BenQ W1060 User Manual

Benq w1060: user guide
Hide thumbs Also See for W1060:
Table of Contents

Advertisement

Quick Links

W1060
Digital Projector
User Manual
Welcome

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the W1060 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for BenQ W1060

Summary of Contents for BenQ W1060

  • Page 1 W1060 Digital Projector User Manual Welcome...

  • Page 2: Table Of Contents

    Securing the projector ......26 Utilizing the password function ..27 Switching input signal ......29 Adjusting the projected image .... 30 Magnifying and searching for details . 32 Selecting the aspect ratio..... 32 Optimizing the image......35 Hiding the image ......... 40 Setting the Sleep Timer .......

  • Page 3: Important Safety Instructions

    Important safety instructions Your projector is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that you follow the instructions mentioned in this manual and marked on the product.
  • Page 4 Safety Instructions (Continued) The lamp becomes extremely hot Do not place this product on an during operation. Allow the unstable cart, stand, or table. The projector to cool for approximately product may fall, sustaining serious 45 minutes prior to removing the damage.
  • Page 5 Always place the projector on a level, horizontal surface during operation. - Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of more than 15 degrees front to back.
  • Page 6 Safety Instructions (Continued) Do not step on the projector or place Ceiling mounting the projector any objects upon it. Besides probable We want you to have a pleasant physical damage to the projector, doing experience using your BenQ projector, so may result in accidents and possible so we need to bring this safety matter injury.

  • Page 7: Introduction

    The apparent brightness of the projected image will vary depending on the ambient lighting conditions, selected input signal contrast/brightness settings, and is directly proportional to projection distance. • The lamp brightness will decline over time and may vary within the lamp manufacturers specifications. This is normal and expected behavior. Introduction...

  • Page 8: Shipping Contents

    Shipping contents Carefully unpack and verify that you have all of the items shown below. If any of these items are missing, please contact your place of purchase. Standard accessories The supplied accessories will be suitable for your region, and may differ from those illustrated.

  • Page 9: Projector Exterior View

    Quick-release button Projection lens External control panel (See "Projector" on page 10 details.) Top IR remote sensor Focus ring and Zoom ring Vent (cool air intake) Front IR remote sensor COMPONENT input jacks S-VIDEO input jack Rear/lower side USB input jack...

  • Page 10: Controls And Functions

    Turns on the On-Screen Display (OSD) When the On-Screen Display (OSD) menu. Goes back to previous OSD menu, menu is activated, the #4, #8 and #11 keys exits and saves menu settings. are used as directional arrows to select the "Using the menus"...

  • Page 11: Remote Control

    Remote control Up cursor/Keystone ( : Navigates and changes settings in the OSD. See "Using the menus" on page for details. : Manually corrects distorted images resulting from an angled projection. "Correcting keystone" on page 31 for details. Left cursor/Decrease volume level ( : Navigates and changes settings in the OSD.
  • Page 12 LIGHT ASPECT Turns on or off the remote control backlight Select the display aspect ratios. See for about 10 seconds. Pressing any other key "Selecting the aspect ratio" on page 32 while the backlight is on keeps the backlight details.

  • Page 13: Remote Control Effective Range

    Remote control effective range Infra-Red (IR) remote control sensor is located on the front and the top of the projector. The remote control must be held at an angle within 30 degrees perpendicular to the projector's IR remote control sensor to function correctly. The distance between the remote control and the sensor should not exceed 7 meters (~ 23 feet).

  • Page 14: Replacing The Remote Control Battery

    Never throw a battery into a fire. There may be danger of an explosion. • If the battery is dead or if you will not be using the remote control for a long time, remove the battery to prevent damage to the remote control from possible battery leakage.

  • Page 15: Positioning Your Projector

    Your room layout or personal preference will dictate which installation location you select. Take into consideration the size and position of your screen, the location of a suitable power outlet, as well as the location and distance between the projector and the rest of your equipment.

  • Page 16: Obtaining A Preferred Projected Image Size

    This is so that they can be readily placed on a table and will project forward and upwards onto a screen positioned so that the bottom edge of the screen is above the level of the table (and everyone in the room can see the screen).

  • Page 17: Screen Size

    How to determine the position of the projector for a given screen size Select your screen size. Refer to the table and find the closest match to your screen size in the left columns labelled "16:9 screen". Using this value, look across this row to the right to find the corresponding average distance from screen value in the column labelled "Average".

  • Page 18: Dimensions

    There is 5% tolerance among these numbers due to optical component variations. BenQ recommends that if you intend to permanently install the projector, you should physically test the projection size and distance using the actual projector before you permanently install it, so as to make allowance for this projector's optical characteristics.

  • Page 19: Connections

    If you wish to make use of the projector (mixed mono) speakers in your presentations, take a suitable audio cable and connect one end of the cable to the audio output jack of the computer, and the other end to the AUDIO jack of the projector. Once connected, the audio can be controlled by the projector On-Screen Display (OSD) menus.

  • Page 20: Connecting Video Source Devices

    • Video (composite) You need only connect the projector to a Video source device using just one of the above connecting methods, however each provides a different level of video quality. The method you choose will most likely depend upon the availability of matching terminals on both the...

  • Page 21: Connecting Hdmi Source Devices

    Connecting HDMI source devices The projector provides a HDMI input jack that allows you to connect it to a HDMI source device like a DVD player, a DTV tuner or a display. HDMI (High-Definition Multimedia Interface) supports uncompressed video data transmission between compatible devices like DTV tuners, DVD players and displays over a single cable.

  • Page 22: Connecting Component Video Source Devices

    If so, you can continue with this procedure. • If not, you will need to reassess which method you can use to connect to the device. To connect the projector to a Component Video source device: Take a Component Video cable and connect the end with 3 RCA type connectors to the Component Video output jacks of the Video source device.
  • Page 23 If so, you can continue with this procedure. • If not, you will need to reassess which method you can use to connect to the device. To connect the projector to an S-Video source device: Take an S-Video cable and connect one end to the S-Video output socket of the Video source device.

  • Page 24: Connecting Composite Video Source Devices

    If so, you can continue with this procedure. • If not, you will need to reassess which method you can use to connect to the device. To connect the projector to a composite Video source device: Take a Video cable and connect one end to the composite Video output socket of the Video source device.

  • Page 25: Operation

    "Turning off the Power on/off Ring Tone" on page 42 details. If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 seconds before energizing the lamp. To use the OSD menus, please set them to your familiar Please select language language first.

  • Page 26: Using The Menus

    Securing the projector Using a security cable lock The projector has to be installed in a safe place to prevent theft. Otherwise, purchase a lock, such as a Kensington lock, to secure the projector. You can locate a Kensington lock slot on the left side of the projector.

  • Page 27: Utilizing The Password Function

    On. The digits being input will display as asterisks on-screen. Write your selected password down here in this manual in advance or right after the password is entered so that it is available to you should you ever forget it.

  • Page 28: Entering The Password Recall Procedure

    Enter a new password. The digits being input will display as asterisks on-screen. Write your selected password down here in this manual in advance or right after the password is entered so that it is available to you should you ever forget it.

  • Page 29: Switching Input Signal

    Switching input signal The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time. You can also manually cycle through the available input signals. Press SOURCE on the projector or remote control.

  • Page 30: Adjusting The Projected Image

    "Correcting keystone" on page 31 for details. • Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes. • Be careful when you press the adjuster button as it is close to the exhaust vent where hot air comes from.

  • Page 31: Correcting Keystone

    Z O O M Correcting keystone Keystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs when the projector is not perpendicular to the screen. To correct this, besides adjusting the height of the projector, and use Auto Keystone or Keystone to manually correct it following one of these steps.

  • Page 32: Magnifying And Searching For Details

    This function is only available with HDMI input source. Selecting the aspect ratio The 'aspect ratio' is the ratio of the image width to the image height. For W1060, the default aspect ration is 16:9. Most analog TV and computers are in 4:3 ratio, and digital TV and DVDs are usually in 16:9 ratio.
  • Page 33 About the aspect ratio In the pictures below, the black portions are inactive areas and the white portions are active areas. OSD menus can be displayed on those unused black areas. Auto: Scales an image proportionally to fit the projector’s native resolution in its 4:3 picture horizontal width and vertical height.
  • Page 34 You could adjust the zoom setting or move the projector away from the screen to increase the image size if necessary. You may also need to refocus the projector after making these adjustments.

  • Page 35: Optimizing The Image

    Setting the User 1/User 2/User 3 mode There are three user-definable modes if the current available picture modes are not suitable for your need. You can use one of the picture modes (except the User 1/User 2/User 3) as a starting point and customize the settings.

  • Page 36: Adjusting Color

    Fine-tuning the image quality in user modes According to the detected signal type, there are some user-definable functions available when User 1, User 2 or User 3 mode is selected. You can make adjustments to these functions based on your needs.

  • Page 37: Selecting A Color Temperature

    “color temperature”. A white color with a low color temperature appears to be reddish white. A white color with a high color temperature appears to have more blue in it.
  • Page 38 The range is from 1 to 4. If you prefer a stronger enhanced image, adjust toward the maximum setting. For a smoother, more natural image, adjust toward the minimum setting.
  • Page 39 Saturation is the amount of that color in a video picture. Lower settings produce less saturated colors; a setting of “0” removes that color from the image entirely. If the saturation is too high, that color will be overpowering and unrealistic.

  • Page 40: Hiding The Image

    On is the default and recommended selection for this projector. When Off is selected, the 3D Comb Filter function is not available. This function is only available when Video is selected.

  • Page 41: Remote Receiver

    1500 m –3000 m above sea level, and temperature is between 5°C–23°C. Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and temperature is between 5°C and 28°C. The projector will be over cooled, if you turn the mode on under such a condition.

  • Page 42: Adjusting The Sound

    Power on/off ring tone and press to select Off. The only way to change Power on/off ring tone is setting On or Off here. Setting the sound mute or changing the sound level will not affect the Power on/off ring tone.

  • Page 43: Personalizing The Projector Menu Display

    Press POWER again to start the projector after the fans stop and the POWER indicator light turns orange.

  • Page 44: Menu Operation

    Menu operation Menu system Please note that the on-screen display (OSD) menus vary according to the signal type selected. Main menu Sub-menu Options Bright/Living Room/Gaming/Cinema//User 1/User 2/ Picture Mode User 3 Reference Mode Bright/Living Room/Gaming/Cinema Brightness Contrast Color PICTURE: Tint...

  • Page 45: System Setup

    PC & Component position/Vertical position/SOG YPbPr Tuning Level Color Space Auto/RGB/YUV Conversion Language Front Table/Rear Table/ Projector Position Rear Ceiling/Front Ceiling 5 sec/10 sec/15 sec/20 sec/25 sec/ Menu Display Time 30 sec Top-Left/Top-Right/Center/ Menu Settings Menu position Bottom-Left/Bottom-Right Reminder SYSTEM On/Off Message...
  • Page 46 • Equivalent Lamp Hour • Firmware Version Note that the menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.

  • Page 47: Description Of Each Menu

    "Adjusting Flesh Tone" on page 36 for details. Save Settings Saves the settings made for User 1 or User 2 or User 3 mode. Reset Picture Resets the picture settings for User 1 or User 2 or User 3 mode.

  • Page 48: Video Format

    3D Comb Filter This function is only available when Video is selected. There are five options to set the image's aspect ratio depending on your Aspect Ratio input signal source. See "Selecting the aspect ratio" on page 32 for details.
  • Page 49 Sets the language for the On-Screen Display (OSD) menus. Language "Using the menus" on page 26 for details. The projector can be installed on a ceiling or behind a screen, or with Projector one or more mirrors. Position "Choosing a location" on page 15 for details.
  • Page 50 Selecting On enables the function and the projector displays the grid Test Pattern test pattern. It helps you adjust the image size and focus and check that the projected image is free from distortion. Closed Caption Selects the screen to display closed captioning text if available.
  • Page 51 Shows input system format, NTSC, PAL, SECAM, or RGB. Equivalent Lamp Hour Displays the number of hours the lamp has been used. Firmware Version Displays the firmware version of the projector. The INFORMATION menu shows you the current operating status of the projector. Operation...

  • Page 52: Maintenance

    Maintenance Care of the projector Your projector needs little maintenance. The only thing you need to do on a regular basis is to keep the lens clean. Never remove any parts of the projector except the lamp. Contact your dealer if other parts need replacing.

  • Page 53: Lamp Information

    You can also get the lamp hour information on the INFORMATION menu. Extending lamp life The projection lamp is a consumable item . To keep the lamp life as long as possible, you can do the following settings via the OSD menu.

  • Page 54: Timing Of Replacing The Lamp

    Timing of replacing the lamp When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode.

  • Page 55: Replacing The Lamp

    To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before changing the lamp. • To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the lamp. •...
  • Page 56 Do not over tighten the screw. Ensure the handle is fully laid flat and locked in place. Replace the lamp compartment cover on the projector and tighten the captive screw. Restart the projector. Do not turn the power on with the lamp cover removed. Maintenance...
  • Page 57 Highlight Reset and press MODE/ENTER. The lamp time will be reset to '0'. Do not reset if the lamp is not new or replaced as this could cause damage. Maintenance...

  • Page 58: Indicators

    Stand-by mode Orange Green Powering up Flashing Normal operation Green The projector needs to cool for 90 seconds after the power is Orange turned off. Flashing Lamp events Orange The lamp ignition retries if the lamp fails during startup. Flashing The projector needs 90 seconds to cool down.

  • Page 59: Troubleshooting

    Troubleshooting The projector does not turn on. Cause Remedy Plug the power cord into the AC inlet on the There is no power from the power projector, and plug the power cord into the cable. power outlet. If the power outlet has a switch, make sure that it is switched on.

  • Page 60: Specifications

    AC100–240V, 50/60 Hz (Automatic) 250W (Max)/ Power consumption <1W (Standby) Mechanical Dimensions 330 mm (W) x 150 mm (H) x 247 mm (D) (Adjust foot max.) Weight 8 lbs (3.63 Kg) Input terminal Computer input RGB input D-Sub 15-pin (female) x 1...

  • Page 61: Dimensions

    Dimensions 330 mm (W) x 119.5 mm (H) x 247 mm (D) 330.0 119.5 58.5 60.0 Ceiling Mount Installation *Ceiling Mount Screws: M4 x L8 (Max. L=12, Min. L=8) 173.7 47.3 121.5 127.0 Unit: mm Specifications...

  • Page 62: Timing Chart

    Timing chart Supported timing for PC input Resolution Horizontal Vertical Pixel Mode Frequency Frequency Frequency (kHz) (Hz) (MHz) 31.469 59.940 25.175 VGA_60 37.861 72.809 31.500 VGA_72 640 x 480 37.500 75.000 31.500 VGA_75 43.269 85.008 36.000 VGA_85 720 x 400 37.927...
  • Page 63 576p(625p)@50Hz 31.25 50.00 720p(750p)@60Hz 45.00 60.00 720p(750p)@50Hz 37.50 50.00 1080i(1125i)@60Hz 33.75 60.00 1080i(1125i)@50Hz 28.13 50.00 1080P@60Hz 67.5 60.00 1080P@50Hz 56.26 50.00 1080P@24Hz 1080P@25Hz 28.12 1080P@30Hz 33.75 • Displaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight image vibration. Specifications...
  • Page 64 Supported timing for Video and S-Video inputs Video mode Horizontal Vertical Color sub-carrier Frequency Frequency Frequency (kHz) (Hz) (MHz) NTSC 15.73 3.58 15.63 4.43 SECAM 15.63 4.25 or 4.41 PAL-M 15.73 3.58 PAL-N 15.63 3.58 PAL-60 15.73 4.43 NTSC4.43 15.73 4.43...
  • Page 65 45.00 74.25 720p_60 VIDEO 28.13 74.25 1080i_50 33.75 74.25 1080i_60 67.5 148.5 1080p 56.26 148.5 1080p 1080P@24Hz 74.25 1080P@24Hz 1080P@25Hz 28.12 74.25 1080P@25Hz 1080P@30Hz 33.75 74.25 1080P@30Hz Displaying a 1080i_50 or 1080i_60 signal may result in slight image vibration. Specifications...

  • Page 66: Warranty And Copyright Information

    BenQ warrants this product against any defects in material and workmanship, under normal usage and storage. Proof of purchase date will be required with any warranty claim. In the event this product is found to be defective within the warranty period, BenQ's only obligation and your exclusive remedy shall be replacement of any defective parts (labor included).

Table of Contents