Advertisement
Quick Links
Pardo European Adjustable Fold Away Bed Systems For Casework
XSMVO WALL BED KIT
1. XWRENCH
*SOLD SEPARATELY
2. ADJUSTABLE COUNTER
BALANCE MECHANISMS
3. PIVOT MOUNTING
MECHANISM PLATES
4. PIVOTING LEGS
5. HARDWARE FASTENERS
1
www.rokhardware.com | support@rokhardware.com | 1-800-763-8390
WALL BED ASSEMBLY
INSTRUCTIONS
The SM Series Bed Mechanisms
2
• VERTICAL DESCENDING
• HORIZONTAL DESCENDING
• CONCEALED HARDWARE
• EXPOSED HARDWARE
• END OPENING
• SIDE OPENING
• SHALLOW WALL CABINETS
• THICK MATTRESS CABINETS
• NATIONWIDE DISTRIBUTION
3
4
5
3
4
Advertisement
Summary of Contents for Rok XSMVO
- Page 1 • CONCEALED HARDWARE • EXPOSED HARDWARE • END OPENING • SIDE OPENING • SHALLOW WALL CABINETS • THICK MATTRESS CABINETS • NATIONWIDE DISTRIBUTION XSMVO WALL BED KIT 1. XWRENCH *SOLD SEPARATELY 2. ADJUSTABLE COUNTER BALANCE MECHANISMS 3. PIVOT MOUNTING MECHANISM PLATES 4.
- Page 2 Foot Concealed Hardware 24mm Hex Adjustment Handle Exposed Hardware Install bed platform in a wall cabinet or between pier cabinets with a bridge. Wall Cabinetry Must be Securely Fastened to a Structural Wall! BEFORE YOU START YOUR PROJECT: • Mattress size will determine the size of the bed frame and the weight capacity of the Pardo counter balance.
- Page 3 HOLE LOCATIONS FOR HARDWARE MOUNTING All measurements are in milimeters Screws DIN 912 M6 x 25 35mm diameter Countersinks x 11mm deep Hole for Hex Nuts DIN 934 M6 Square Axel Holes for Mounting Plate Countersink 35x11 Components are produced in Europe using metric dimensions. 350+ SUPPLIED COUNTERSINK...
- Page 4 CABINETRY DIMENSIONS FOR END OR VERTICAL OPENING WALL BED CONSTRUCTION INSIDE BED FRAME MECHANISM OUTSIDE BED FRAME MECHANISM Twin Double Queen King¹ Twin Double Queen King¹ Part Number XSMVO- 3950I 5475I 54110I 54110I 1235678 1234678 1234678 1234678 Design Weight 110# 165# 243# 260#...
- Page 5 BED FRAME DETAIL 1” x 2” cleat Bull nose top of head board on support bed frame flush to mattress slats or platform, if used Head Board end only mattress retainer when closed 4” 3/4” 2-3/4” www.rokhardware.com Wall Bed Assembly Instructions...
- Page 6 A 3/4” HARDWOOD PLYWOOD CABINET BACK MUST BE PROVIDED FOR CABINET INTEGRITY AND ATTATCHMENT OF THE CABINET TO A STRUCTURAL WALL. THE PLATFORM CAN WEIGH SEVERAL HUNDED LBS, AND WILL BE IN MOTION WHEN OPENING OR CLOSING. Lift door platform and bed frame on a 45º angle Close and open the door panel to insure against to clear all obstructions and lower the assembly obstruction of movement.
-
Page 7: Adjustment Procedure
WALL BED INSTALLATION AND ADJUSTMENT Adjusting the gap 30mm around door. Leveling Screw Square Axel Socket head screw in During Installation square axel is used end of “C” to be flush for adjusting the door reveal. Adjust tension and balance the bed platform. -
Page 8: Important Safety Information
COUNTERSINK BUSHINGS REQUIRED Countersink busings are supplied with the wall bed system hardware and MUST be inserted in counter bores to attach the pivot mounting mechanislm plate to the side wall of the cabinet or piers and to attach the counter balance mechanisms to the bed frame with appropriate machine screws and washers.
Need help?
Do you have a question about the XSMVO and is the answer not in the manual?
Questions and answers