Advertisement
Parts List
Parts List
No.
Name
1
Electric Leg A
Main Beam
2
Control Box
3
4
Electric Leg B
Feet
5
Sub-beam
6
7
Bracket
Handset
8
Screw Bag
No.
Name
1
M6*8 Screw
2
M6*10 Screw
3
M6*12 Screw
4
M6*40 Screw
5
Plastic Plug
6
Rubber Cushion
7
ST3.5*19 Screw
8
ST4.8*19 Screw
9
ST4.8*25 Screw
10
4mm Hex Spanner
11
5mm Hex Spanner
Qty
1
1
1
2
3
1
3
1
8
7
Qty
2
8
1
18
12
10
10
2
9
2
10
1
1
1
2
2
3
4
10
11
3
4
5
6
5
6
7
8
Advertisement
Table of Contents
Summary of Contents for Ascend ALPHA
- Page 1 Parts List Parts List Name Electric Leg A Main Beam Control Box Electric Leg B Feet Sub-beam Bracket Handset Screw Bag Name M6*8 Screw M6*10 Screw M6*12 Screw M6*40 Screw Plastic Plug Rubber Cushion ST3.5*19 Screw ST4.8*19 Screw ST4.8*25 Screw 4mm Hex Spanner 5mm Hex Spanner...
- Page 2 Assembly Instructions Loosen the M6*10 screws on the main beam with 4mm hex spanner, then adjust the Attach the electric legs to the beam using 8 of M6*12 screws. length of the beam according to the desktop, and finally secure the beam using 4 of M6*10 screws from the screw pack along with the screws on the beam.
- Page 3 Assembly Instructions Attach the desk frame to below desktop using 10 of ST4.8*25 screws, then attach the control box to below desktop using 2 of ST4.8*19 screws, at last attach the handset to below desktop using 2 of ST3.5*19 screws. ST4.8*25 Screw 2pcs ST4.8*19 Screw 2pcs ST4.8*25 Screw 4pcs...
-
Page 4: Handset Interface
ASCEND ALPHA/OMEGA Handset Operation Manual 1 2 3 4 M 8.8.8 1.Handset Interface ▶ UP ▶ DOWN ▶ Setting Button M ▶ Height Memory Button 1 ▶ Height Memory Button 2 ▶ Height Memory Button 3 ▶ Height Memory Button 4 2.Initialization Operation... -
Page 5: Lock And Unlock
5.Upper and Lower Limit Settings ▶ The system supports the height limit of the desk. The operation method is, press and hold the <↑>&<↓> at the same time for 5 seconds at the corresponding height until hear the buzzer, indicating the limit position is stored successfully. When the desk is in the upper half of the stroke, the limit is the highest position. -
Page 6: Internal Parameters
9.Internal Parameters ▶ Long press <M> for 15 seconds, handset display shows "S-x", and "x" flashes ( "x" is the parameter group). At this time, press <M> to enter the parameter group to set the corresponding parameters, and press <↑> or <↓> to switch the parameter group. - Page 7 Error Code Possible Cause Action Wait for motor to cool. Temperature of motor is high or running Let system rest for at least 18 mins. time exceeds 2 mins within 18 mins. The Motor 1 is not connected. Check power cable of motor. Error in the Motor 1 current sampling channel.
Need help?
Do you have a question about the ALPHA and is the answer not in the manual?
Questions and answers