Carousel USA 12LD Manual
  1. Manuals
  2. Brands
  3. Carousel USA Manuals
  4. Controller
  5. 12LD
  6. Manual

Carousel USA 12LD Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Carousel USA
15206 Ceres Ave.
Fontana, CA 92335
626-334-7190
12LD Controller Outline
Contents
1.
Introduction .......................................................................................................................................... 2
a.
Content of Carousel USA Agreement ................................................................................................ 2
b.
Components ...................................................................................................................................... 2
2.
Control Panel ......................................................................................................................................... 2
a.
Enclosure Specifications .................................................................................................................... 2
b.
Connections ...................................................................................................................................... 2
c.
Electrical Schematic .......................................................................................................................... 2
d.
Front Panel Layout ............................................................................................................................ 3
3.
Standard Operating Procedure ............................................................................................................. 3
12LD Outline Rev 1
6/25/2024
Page 1 of 3

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 12LD and is the answer not in the manual?

Questions and answers

Related Manuals for Carousel USA 12LD

Summary of Contents for Carousel USA 12LD

  • Page 1 15206 Ceres Ave. Fontana, CA 92335 626-334-7190 12LD Controller Outline Contents Introduction ............................2 Content of Carousel USA Agreement ....................2 Components ............................2 Control Panel ............................2 Enclosure Specifications ........................2 Connections ............................2 Electrical Schematic .......................... 2 Front Panel Layout ..........................3 Standard Operating Procedure ......................
  • Page 2 This document is intended to further detail the standard turntable controller equipment described in the contractual agreement. It will cover functionality and provides step-by-step standard operating procedures. a. Content of Carousel USA Agreement CUSA Standard Controls, with one (1) remote transmitter. b. Components...
  • Page 3 3. Turntable can now be rotated clockwise or counterclockwise using the buttons on the remote control. 4. Turntable rotation speed can be adjusted using the dial on the front of the drive. 12LD Outline Rev 1 6/25/2024 Page 3 of 3...
  • Page 4 Proprietary InformationCarousel USA has proprietary rights on the information in this document. It is forbidden to copy, duplicate or disclose the information herein, in whole or in part, or make use of the information, unless permission has been previously obtained, in writing, from Carousel USA.

  • Page 5: Table Of Contents

    ONTROLS ESTING 12LD-A ..............................11 12LD-O ..............................11 SONOFF WIRELESS RECEIVER (12LD-O MODEL ONLY) ............... 12 PAIRING THE REMOTE ......................... 13 PHONE APP CONFIGURATION ....................... 13 P a g e 2 o f 1 3 w w w . c a r o u s e l - u s a . c o m...

  • Page 6: External Panel Layout

    If it is in the “on” position and the light is not on, this indicates a problem with either the power cable, or incoming power from the wall outlet. B. Front Panel Layout (12LD-O) Motor Driver with Cover On Motor Driver with Cover Off Once power is on, check the Red LED Display on the motor driver shown above.

  • Page 7: Front Panel Layout (12Ld-A)

    Unlike the 12LD-O, the motor driver for the 12LD-A model does not include alarms or navigation to change parameters, meaning it does not give troubleshooting information aside from a confirmation that incoming power is ok via the LED speed display. If you have a 12LD-O model, skip ahead to Section 7, General Troubleshooting.

  • Page 8: Motor Driver Alarms Table (12Ld-O)

    -USA T AROUSEL ROUBLESHOOTING GUIDE 4. Motor Driver Alarms Table (12LD-O) ***NOTE: Driver alarms, navigation, and parameters only available for model 12LD-O*** Alarm Alarm Type Cause Next Steps Code AL20 Overcurrent Excessive current Check the Motor Cable coming has flown through...
  • Page 9 -USA T AROUSEL ROUBLESHOOTING GUIDE AL30 Overload A load exceeding Reduce load on the turntable, or the continuous increase duty region was acceleration/deceleration time applied to the using the knob on the front of the motor driver AL31 Overspeed The rotation speed Reduce load on the turntable, or of the motor increase...

  • Page 10: Motor Driver Navigation (12Ld-O)

    AROUSEL ROUBLESHOOTING GUIDE 5. Motor Driver Navigation (12LD-O) ***NOTE: Driver alarms, navigation, and parameters only available for model 12LD-O*** Motor Driver with Cover Off Motor Driver with Cover On 1. Upon initial power up, the motor driver will display zero, indicating that the motor is not in motion.

  • Page 11: Motor Driver Parameters (12Ld-O)

    -USA T AROUSEL ROUBLESHOOTING GUIDE 6. Motor Driver Parameters (12LD-O) ***NOTE: Driver alarms, navigation, and parameters only available for model 12LD-O*** Item Display Description Factory Setting Speed Reduction Ratio Gr-r Sets ratio of rotational 1.00 speed of the turntable vs...
  • Page 12 -USA T AROUSEL ROUBLESHOOTING GUIDE External Operation Signal ioEn Sets whether external rE (Allows Input inputs can be used to start external or stop the motor operation)*** X0 Input Function in-0 Assigns input signals to FYD (Forward) Selection each of the external input terminals X1 Input Function in-1...

  • Page 13: General Troubleshooting

    Carousel-USA Logo plate and lifting it apart from the rest of the control box. 12LD Internal Layout (Wireless Receiver Only in 12LD-O Model) ***DISCLAIMER*** Before performing any work involving removing wire from terminals, ensure that power is turned off and proper precautions are taken to avoid electrical shock.

  • Page 14: Check Circuit Breaker

    D. Controls Testing If the motor driver has power, begin by testing each control method available to you. 12LD-A Using the motor driver, attempt to run the table in both directions and using different speeds. Record which of these moves the table, as well as if there are any concerning mechanical sounds while running or attempting to run the table.

  • Page 15: Sonoff Wireless Receiver (12Ld-O Model Only)

    AROUSEL ROUBLESHOOTING GUIDE 8. Sonoff Wireless Receiver (12LD-O Model Only) If the motor driver runs the table, but the wireless remotes and/or phone app do not, inspect the Sonoff Wireless Receiver inside the control box for loose connections and/or obviously damaged wiring.

  • Page 16: Pairing The Remote

    -USA T AROUSEL ROUBLESHOOTING GUIDE 9. Pairing the Remote 1. To pair the remote to the receiver, press and hold the R1 pairing button on the receiver for about 3 seconds, until the Wi-Fi LED indicator turns red and quickly flashes once, then release R1 and briefly press the A button on the remote.

Table of Contents