Advertisement
Advertisement
Table of Contents
Summary of Contents for EL DORADO FURNITURE 8257
- Page 1 GAMING CHAIR Installation Manual www.eldoradofurniture.com...
-
Page 2: Assembly Guide
ASSEMBLY GUIDE Congratulations, you are now the owner of a brand new El Dorado Furniture chair! Before enjoy the comfort chair, you have to put it together.This Assembly Guide will take you through the basic assembly process. To make sure your assembly goes smoothly, please follow the assembly instructions, and especially the important safety information. -
Page 3: Component List
customercare@eldoradofurniture.com COMPONENT LIST Casters Star Base Gas Lift Quantity: 5 Quantity: 1 Quantity: 1 Armrests Seat Plate Steel Plate Quantity: 2 Quantity: 1 Quantity: 1 Pillows Back Cushion Seat Cushion Quantity: 1 Quantity: 1 Quantity: 1 Spacer Bolts M6*20mm Bolts M8*25mm Bolts M8*20mm Bolts M6*45mm Quantity: 8... - Page 4 customercare@eldoradofurniture.com ASSEMBLY INSTRUCTIONS STEP 1 : Turn the Star Base upside down, then press the Casters into the holes at the end of each base leg. STEP 2 : Turn the Star Base upright and insert the Lift into the center hole of the Star Base.
- Page 5 customercare@eldoradofurniture.com ASSEMBLY INSTRUCTIONS STEP 3 : Align the seat plate to the bottom of the seat cushion, make sure that the front of the seat plate is facing the front of the seat cushion. Put the spacer rings between the mechanism and seat plate. Attach the seat plate to the seat cushion using four M6X20mm bolts, tighten all the bolts with the T-wrench.
- Page 6 customercare@eldoradofurniture.com ASSEMBLY INSTRUCTIONS STEP 5 : Attach the Steel Plate to the back cushion with four M8x25mm Bolts. STEP 6: Attach Seat Cushion and Back Cushion, align the Steel Plate over the pre-drilled holes underneath the back cushion with three M8x20mm Bolts, tighten all the bolts with the T-wrench.
- Page 7 customercare@eldoradofurniture.com ASSEMBLY INSTRUCTIONS STEP 7: Attach the arms to the seat cushion with four M6X45mm bolts, using the T-Wrench. Note: Arm rests are labeled with an “L”(left) or “R”(right) to show which sides they should be placed on. STEP 8: Lay the back cushion on the seat of the chair with the top of the cushion toward the front.
- Page 8 customercare@eldoradofurniture.com ASSEMBLY INSTRUCTIONS Adjust the balance, then fully tighten all the bolts on STEP 9: each side of adjusters. tighten all the bolts with the T-wrench. STEP 10 : (100%) STEP 11: Press the plastic caps into the adjuster holes to cover the bolts.
- Page 9 customercare@eldoradofurniture.com ASSEMBLY INSTRUCTIONS STEP 12: Zipper between the back cushion and the seat pad Congratulations!You’ve assembled your Gaming chair.
- Page 10 customercare@eldoradofurniture.com INSTRUCTIONS FOR USE Seat Height: Paddle-First lever on right side To raise: While taking your weight off chair, lift lever up. To lower: While seated, lift lever up. At the proper height, your feet should rest flat on the floor. Operating the tilt lockout- the second lever on right side Push down to lock the tilt mechanism.
-
Page 11: Safety And Maintenance
customercare@eldoradofurniture.com SAFETY AND MAINTENANCE Do not stand on the chair, Do Not use the chair as stepladder. Use this product for seating one person at a time. red. Avoid contact with sharp objects to prevent puncturing the fabric. Every 6 months, check all bolts and screws to ensure they are tight. To clean, spot clean only using a damp towel and mild cleaner, first test on a small,, obscure area of fabric. - Page 12 www.eldoradofurniture.com customercare@eldoradofurniture.com...
Need help?
Do you have a question about the 8257 and is the answer not in the manual?
Questions and answers