VEIKOUS GARDEN SHED 10'x12' Assembly Manual
  1. Manuals
  2. Brands
  3. VEIKOUS Manuals
  4. Garden Houses
  5. GARDEN SHED 10'x12'
  6. Assembly manual

VEIKOUS GARDEN SHED 10'x12' Assembly Manual

Hide thumbs

Advertisement

Table of Contents

GARDEN SHED 10'x12'
ASSEMBLY MANUAL

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the GARDEN SHED 10'x12' and is the answer not in the manual?

Questions and answers

Chip
February 28, 2025

How do you put a 10x12 Sheldon a 8x12 base

0
1 comments:
Mr. Anderson
February 28, 2025

The VEIKOUS 10'x12' garden shed is designed for a foundation size of 141.7" x 95" (approximately 11.8' x 7.9'). If your base is 8' x 12', it is too small for proper installation. You should ensure that the base matches the required foundation size before proceeding with installation.

This answer is automatically generated

0

Subscribe to Our Youtube Channel

Summary of Contents for VEIKOUS GARDEN SHED 10'x12'

  • Page 1 GARDEN SHED 10’x12’ ASSEMBLY MANUAL...
  • Page 3 TOOlS Required Electric drill Gloves Ladder Tape Measure Pencil Safety Glasses Hammer Paint Tools Optional Nail Gun Hand Saw ORIENT LUMBER AND TRIM FOR BEST APPEARANCE Always install the material leaving the best edge and best surface visible. Please remember that these blemishes in no way negatively affect the strength or integrity of our product.（See Fig A.B.C).
  • Page 4 CONCRETE FOUNDATION If you choose to install your kit on a concrete slab refer to the diagram below. Caulk between sill plate and concrete. Concrete 4”(10.2cm) Concrete Foundation Size 141.7” X95”(360 X 241.2cm) 141.7”(360cm) 86.9”(285cm) 95”(305cm) Foundation material (Not Included) : 2x4x11.8’(5.1x10.2x360cm) Note:Must be treated lumber.
  • Page 5 BUILD YOUR OWN WOOD FLOOR OPTION (Materials not included.) Wood Floor Size 141.7” X95”(360 X 241.2cm) 141.7”(360cm) 86.9”(285cm) 95”(305cm) Foundation material (Not Included) : 2x4x11.8’(5.1x10.2x360cm) Note:Must be treated lumber. 2x4x7.24’(5.1x10.2x285cm) 4x4x11.8’(10.2x10.2x360cm) 5/8”x48”x96”(1.6x121.9x243.8cm) 3" (7.6 cm) Hot Dipped Screws...
  • Page 6 ADDITIONAL MATERIALS (Not Included) After building your shed，you will need the following materials to make your shed waterproof and decorative. PAINT FOR SIDING --------------------------------------------(3 Gallons) Use 100% acrylic latex exterior paint. (2) coats recommended. PAINT FOR TRIM ----------------------------------------------(2 Quarts) Use 100% acrylic latex exterior paint. CAULK ----------------------------------------------------------(2 Tubes) Use acrylic latex exterior caulk that is paintable.

  • Page 7: Parts Identification

    PARTS IDENTIFICATION Part identification letters are stamped on certain parts. Check these locations for part stamp. PARTS LIST AND SIZES √ INVENTORY YOUR PARTS before you begin. 2.36x1.57x59in (6x4x150 CM) 2.36x1.57x75.6in (6x4x192 CM) 2.36x1.57x77.3in (6x4x196.3 CM) 2.36x1.57x58.7in (6x4x149.3 CM) 2.36x1.57x68in (6x4x172.8 CM) 2.36x1.57x30.7in (6x4x78 CM)
  • Page 8 2.36x1.57x23.6in (6x4x60 CM) 1.97x1.97x76.9in (5x5x195.4 CM) 3.31x1.77x0.94in (8.4x4.5x2.4 CM) 2.36x2.36x69.3in (6x6x176 CM) 2.36x2.36x69.3in (6x6x176 CM) 4.72x23.6x1in (12x60x2.5 CM) PANEL PARTS LIST Wall panels are 0.47in(1.2 cm) thick.
  • Page 9 Ix1 DOOR Jx1 DOOR Hx1 WINDOW METAL ROOFING PE4x14 PE5x2 PE6x2 PE7x2...

  • Page 10: Door Hardware

    M11Ax4 M11Bx2 M13Bx1 M13Ax2 DOOR HARDWARE x2 Door Latch x1 Lock with Screws x2 Long Hinge...

  • Page 11: Hardware Accessories

    HARDWARE ACCESSORIES NOTE: F1x260 M4x10 If a nail gun is used, nails may be used at the screws locations shown to speed up F2x80 M4x30 assembly. Nails must be the same length as the screws. F3x480 M5x35 F4x60 M5x50 F5x320 M5x60 Washer Sheet Vx260...
  • Page 12 WALL INDEX Create your own style of shed. Choose your door location.Use this guide to find the corresponding wall construction and installlation pages. 10' x 12' Door on eave wall 10' x 12' Door on gable wall GABLE WALL 01 BACK EAVE WALL 02 GABLE WALL 01 BACK EAVE WALL 02...
  • Page 13 GABLE WAll 01 PARTS REQUIRED: F5x32 2.36x1.57x59in(6x4x150 CM) 2.36x1.57x75.6in(6x4x192 CM) Arrange the parts edge to edge on the floor as shown. Measure and mark from the end of the boards.Secure with (2) F5 Screws at each connection and (4) F5 Screws at the seams. 118.1in (300cm) 106.3in...
  • Page 14 GABLE WAll 01 PARTS REQUIRED: F3x68 Install wall panels with primer side up as shown. Secure wall panels with F3 Screws spaced 11.4 in (29 cm) horizontally and 15.4 in (39 cm) vertically. Mark the wall panels with a pencil before Flush screwing in the screws as shown.
  • Page 15 BACK EAVE WAll 02 PARTS REQUIRED: F5x68 2.36x1.57x68in(6x4x172.8 CM) 2.36x1.57x75.6in(6x4x192 CM) Arrange the parts edge to edge on the floor as shown. Measure and mark from the end of the boards.Secure with (2) F5 Screws at each connection and (4) F5 Screws at the seams. 136.1in （345.6cm）...
  • Page 16 BACK EAVE WAll 02 PARTS REQUIRED: F3x66 Install wall panels with primer side up as shown. Secure wall panels with F3 Screws spaced 11.4 in (29 cm) horizontally and 15.4 in (39 cm) vertically. Mark the wall panels with a pencil before 2.83in （7.2cm）...
  • Page 17 FRONT EAVE WAll 03 PARTS REQUIRED: 2.36x1.57x75.6in(6x4x192 CM) 2.36x1.57x68in(6x4x172.8 CM) 2.36x1.57x6.7in(6x4x17 CM) 2.36x1.57x77.3in(6x4x196.3 CM) 2.36x1.57x64.4in(6x4x163.6 CM) 2.36x1.57x58.7in(6x4x149.3 CM) 2.36x1.57x23.6in(6x4x60 CM) F5x56 2.36x1.57x30.7in(6x4x78 CM) Arrange the parts edge to edge on the floor as shown. Measure and mark from the end of the boards.Secure with (2) F5 Screws at each connection and (4) F5 Screws at the seams.
  • Page 18 FRONT EAVE WAll 03 F3x75 PARTS REQUIRED: B1x1 B2x1 Flush Mark the wall panels with a pencil before 2.83in screwing in the screws （7.2cm） as shown. Flush 2.83in 2.83in （7.2cm） （7.2cm）...
  • Page 19 FRONT EAVE WAll 04 (OPTION) PARTS REQUIRED: 2.36x1.57x75.6in(6x4x192 CM) 2.36x1.57x68in(6x4x172.8 CM) 2.36x1.57x77.3in(6x4x196.3 CM) 2.36x1.57x23.6in(6x4x60 CM) F5x42 2.36x1.57x58.7in(6x4x149.3 CM) 2.36x1.57x30.7in(6x4x78 CM) Arrange the parts edge to edge on the floor as shown. Measure and mark from the end of the boards.Secure with (2) F5 Screws at each connection and (4) F5 Screws at the seams. 136.1in （345.6cm）...
  • Page 20 FRONT EAVE WAll 04 (OPTION) PARTS REQUIRED: F3x75 Flush Mark the wall panels with a pencil before screwing in the screws 2.83in as shown. （7.2cm） Flush 2.83in 2.83in （7.2cm） （7.2cm）...
  • Page 21 GABLE WAll 05 (OPTION) PARTS REQUIRED: F5x32 2.36x1.57x59in(6x4x150 CM) 2.36x1.57x6.7in(6x4x17 CM) 2.36x1.57x75.6in(6x4x192 CM) 2.36x1.57x64.4in(6x4x163.6 CM) Arrange the parts edge to edge on the floor as shown. Measure and mark from the end of the boards.Secure with (2) F5 Screws at each connection and (4) F5 Screws at the seams. 118.1in (300cm) 106.3in...
  • Page 22 GABLE WAll 05 (OPTION) PARTS REQUIRED: B1x1 F3x62 B2x1 Mark the wall panels with a pencil before screwing in the screws as shown.
  • Page 23 GABLE UNITS PARTS REQUIRED: 2.36x1.57x59.5in (4x3x151.2 CM) E1x2 E2x2 2.36x1.57x65.7in (6x4x166.8 CM) 2.36x1.57x20.2in (6x4x51.3 CM) 3x1x67.8in (7.6x2.5x172.3 CM) 3x1x58.9in (7.6x2.5x149.5 CM) Repeat two times F5x20...
  • Page 24 GABLE UNITS Repeat two times F3x58 Repeat two times F3x32 Flush Flush...
  • Page 25 BACK / GABLE WALL INSTALLATION F3x8 BACK EAVE WALL 02 GABLE WALL 01...
  • Page 26 BACK / GABLE WALL INSTALLATION F3x8 F5x10 BACK EAVE WALL 02 GABLE WALL 01 GABLE WALL 01...
  • Page 27 FRONT EAVE WALL INSTALLATION F3x16 GABLE WALL 01 BACK EAVE WALL 02 GABLE WALL 01 FRONT EAVE WALL 01 STANDARD: DOOR LOCATED ON 12'EAVE WALL OPTIONAL: DOOR LOCATED ON 10'GABLE WALL...
  • Page 28 FRONT EAVE WALL INSTALLATION F5x10 GABLE WALL 01 FRONT EAVE WALL 01 BACK EAVE WALL 02 GABLE WALL 01...
  • Page 29 GABLE UNITS INSTALLATION F4x24 F4 F4 F4x6...
  • Page 30 EAVE INSTALLATION 3x1x70.9in F4x16 (7.6x2.5x180 CM) Flush...
  • Page 31 RAFTER INSTALLATION 2.36x1.57x66.2in F3x20 (6x4x168.1 CM) 4.72x23.6x1in (12x60x2.5 CM)
  • Page 32 RAFTER INSTALLATION F5x4 F5x2 F5x2 F5x2 Flush Center...
  • Page 33 ROOF BEAM INSTALLATION 2.36x1.57x70.4in F4x16 (6x4x178.8 CM)
  • Page 34 METAL ROOFING INSTALLATION Vx108 F1x108...
  • Page 35 METAL ROOFING INSTALLATION F1x108 Vx108...
  • Page 36 FASCIA TRIM INSTALLATION 2.36x2.36x69.3in (6x6x176 CM) 2.36x2.36x69.3in (6x6x176 CM) F3x12...
  • Page 37 RIDGE CAP INSTALLATION F1x8 M13A M13B M13A M13B M13A...
  • Page 38 RIDGE CAP INSTALLATION F1x8 M11A M11B M11A M11A M11B M11A M11A M11B...

  • Page 39: Window Installation

    WINDOW INSTALLATION Use silicone sealant to seal the window Seal the window by applying a high quality exterior-grade caulk to the back of the frame near the edge before installation.

  • Page 40: Right Door

    LEFT DOOR F2x18 F2x18 RIGHT DOOR F2x18 F2x18...
  • Page 41 DOOR HARDWARE INSTALLATION F2x17 F2x17...
  • Page 42 DOOR HARDWARE INSTALLATION F2x17 F2x17...
  • Page 43 DOOR HARDWARE INSTALLATION Door Latch X2 Lock with Screws X1 F2x8 F3x2 3.31x1.77x0.94in (8.4x4.5x2.4 CM) Top door beam Mark the location of the top and bottom door beams with a pencil, then punch holes with a suitable drill bit. Bottom door beam Screw...
  • Page 44 CORNER TRIM INSTALLATION 1.97x1.97x76.9in (5x5x195.4 CM) F3x32...
  • Page 45 ENJOY YOUR PRODUCT ！...

Table of Contents

Save PDF