Summary of Contents for Zycoo iSpeaker-C20
- Page 1 VoIPon www.voipon.co.uk sales@voipon.co.uk Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299...
-
Page 2: Table Of Contents
Change Login Password of Web ................. 13 Firmware Upgrade ...................... 13 Restore to Factory Default ..................14 Reboot ......................... 14 Copyright © ZYCOO All Rights Reserved 2 / 14 VoIPon www.voipon.co.uk sales@voipon.co.uk Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299... -
Page 3: Brief Introduction
The device supports POE by default. If the power supply is needed to connect, please use only the power adapter provided by ZYCOO. Other power supplies may damage or even destroy the device, and as such will not be covered by the product warranty. -
Page 4: Device Installation
LAN2 is used to connect other devices for expanding your network. If your IP PBX server doesn’t support PoE then please use the 5V/1A power supply provided by Zycoo to power the iSpeaker. The interface of “SPK+” and “SPK-” are used to connect a loudspeaker. If you plan to use headset then please plug the microphone of headset into “Audio in”... -
Page 5: Configuration
Notice: Please use IE browser(Ver8.0 or higher), Firefox or Chrome. Step3. Input default username (admin) and password(admin). Default URL Address: http://192.168.119.110/ Default Username：admin Copyright © ZYCOO All Rights Reserved 5 / 14 VoIPon www.voipon.co.uk sales@voipon.co.uk Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299... -
Page 6: Network Configuration
Step2. After completing configuration, click 【Submit】 to display the following window. You must choose 【Continue】 to make additional changes, or 【Apply Now】 to apply changes to the device. Copyright © ZYCOO All Rights Reserved 6 / 14 VoIPon www.voipon.co.uk sales@voipon.co.uk Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299... -
Page 7: Sip Registration
The time of Auto answer (by second). Default is 1; if set as 0, there is no auto answer. Audio Output Mode Output mode of audio (Speaker or Handset). Default is Speaker. Copyright © ZYCOO All Rights Reserved 7 / 14 VoIPon www.voipon.co.uk sales@voipon.co.uk Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299... -
Page 8: Sip Advanced Configuration
Set hex value of RTP DSC. Default is 68. 6.3 SIP Voice Codec Click 【Codecs】 to configure the priority order of SIP codecs. After configuration, click 【Submit】 . Copyright © ZYCOO All Rights Reserved 8 / 14 VoIPon www.voipon.co.uk sales@voipon.co.uk Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299... -
Page 9: Sip Auto Provision (Hidden By Default)
Step2. Click 【PnP Settings】 to configure your PnP settings including input URL. Use the default multicasting address: 224.0.1.75 and the default port of 5060. Copyright © ZYCOO All Rights Reserved 9 / 14 VoIPon www.voipon.co.uk sales@voipon.co.uk Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299... - Page 10 Step3. Click 【Phone Settings】 【New Phone】to configure iSpeaker information. New Phone: Item Explanation Enable Enable to make the phone provisioning effective Manufacturer Select the manufacture of iSpeaker: Zycoo Type Select device type: iSpeaker MAC of iSpeaker device Extension Select extension number of iSpeaker Speaker Name If iSpeaker supports LCD, the speaker name will be displayed on the LCD.
- Page 11 Provisioning, e.g.: http://192.168.2.24, input default username and password “admin/admin”, you will then see the device information which confirms iSpeaker is registered. Copyright © ZYCOO All Rights Reserved 11 / 14 VoIPon www.voipon.co.uk sales@voipon.co.uk Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299...
-
Page 12: Volume Settings
Click 【 Pin Active】 to apply the function of Pin2 to Pin 4(Pin 1 is for GND by default). Enable the Pin function by ticking the check box. Copyright © ZYCOO All Rights Reserved 12 / 14 VoIPon www.voipon.co.uk sales@voipon.co.uk Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299... -
Page 13: System Management
9.3 Firmware Upgrade Click 【Administration】 【Firmware Upgrade】 to upgrade the firmware. Download the firmware from Zycoo’s official website. To Ensure a successful upgrade, please modify the Copyright © ZYCOO All Rights Reserved 13 / 14 VoIPon www.voipon.co.uk sales@voipon.co.uk Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299... -
Page 14: Restore To Factory Default
The system will be reset after 3~5 seconds, all settings will be cleared and reset to factory default. 9.5 Reboot Click 【Administration】【Reboot】 and click the button “Reboot”, the system will reboot after 3~5 seconds. Copyright © ZYCOO All Rights Reserved 14 / 14 VoIPon www.voipon.co.uk sales@voipon.co.uk Tel: +44 (0)1245 808195 Fax: +44 (0)1245 808299...
Need help?
Do you have a question about the iSpeaker-C20 and is the answer not in the manual?
Questions and answers