Summary of Contents for ETC echoflex Elaho
- Page 1 Elaho Astronomical TimeClock Configuration Manual Version 3.3 Part Number: 8186M1230-3.3.4 Rev A Released: 2021-04...
- Page 2 To view a list of Echoflex Solutions trademarks and patents, go to echoflexsolutions.com/ip. All other trademarks, both marked and not marked, are the property of their respective owners. Echoflex Solutions intends this document, whether printed or electronic, to be provided in its entirety.
-
Page 3: Table Of Contents
Table of Contents Overview Features Warnings and Notice Conventions Help from Technical Services Specification Ambient Environment Compliance Electrical Requirements Mounting Requirements Elaho Control System Installation and Setup Connect Wiring Install the E-ATC into the Back Box Install the Faceplate User Interface Overview Keypad Display Status Display... - Page 4 Timed Hold Indefinite Hold Recall Preset Main Menu Schedule Events Auto Timed Hold Schedule an Event Open/Close Settings Timeclock Settings Change Current Time Change Time Style Change Current Date Configure Hold Time Set Flick Warn Set Warn Time Set Time Zone Set Latitude and Longitude Set Daylight Saving Time Set Manual DST Dates...
-
Page 5: Overview
Overview Welcome to the Elaho Astronomical TimeClock (E-ATC) Installation and Configuration Manual. This guide contains the procedures for successful programming of the E-ATC when used as part of an Elaho control system. The E-ATC provides Elaho power control systems with low-cost, easy-to- use, and easy-to-program time-based control. -
Page 6: Warnings And Notice Conventions
Warnings and Notice Conventions These symbols are used throughout Echoflex Solutions documentation to alert you to danger or important information. Note: Notes are helpful hints and information that are supplemental to the main text. CAUTION: A Caution statement indicates situations where there may be undefined or unwanted consequences of an action, potential for data loss or an equipment problem. -
Page 7: Help From Technical Services
Help from Technical Services If you are having difficulties and your problem is not addressed by this document, try the Echoflex website at echoflexsolutions.com. If none of these resources are sufficient, contact Echoflex Technical Services directly at the office identified below. When calling for help, take these steps first: Prepare a detailed description of the problem •... -
Page 8: Specification
Specification Note: Installation must follow all national and local codes for electrical equipment. Ambient Environment For indoor, commercial controls use only. Operating temperature 0°C– 40°C, 5–95% non-condensing humidity. Compliance UL and cUL LISTED • CE marked • Meets California Title 24 •... - Page 9 EchoConnect The E-ATC requires EchoConnect. EchoConnect is a bi-directional protocol that uses one pair of wires (data + and data -) for both data and power. Echoflex Solutions recommends using Belden 8471 Class 2 wire (or approved equal - see the Echoflex Solutions cable cross database echoflexsolutions.com/files/Elaho_Data_Cable_Wire_Specs for equal alternatives).
-
Page 10: Mounting Requirements
Mounting Requirements The E-ATC is capable of flush or surface mounting for installation in any location with conditions meeting the ambient environment requirements listed in Ambient Environment on page 4 Alternatively, the E-ATC can be integrated into an Elaho Room Controller. Flush Flush mount the E-ATC to an industry standard two-gang back box, not provided. -
Page 11: Elaho Control System
Elaho Control System Elaho control system utilizes the EchoConnect bus for communication, allowing Elaho enabled products to interact. An Elaho control system is limited to 16 Elaho control products and 16 Elaho output products. If more Elaho products are required in a system, an Elaho Expansion Bridge may be added to the system. - Page 12 E-ATC with Elaho Station Power Module with Aux Power Station Power Supply with Aux Power a variety of form factors and mounting options are available (not included) TimeClock Recall Preset Back Enter Down Hold EchoConnect (Belden 8471 + (1) 14 AWG ESD ground wire) Astronomical TimeClock Configuration Manual...
-
Page 13: Installation And Setup
Installation and Setup The Elaho Astronomical Timeclock (E-ATC) is designed to install into a flush mounted, industry standard, two gang back box (provided by others). Installation should follow local codes and standard practices. Install the back box flush and square for best installation results. Alternatively, a surface mounted back box may be used (sold separately and available from Echoflex Solutions.) Connect Wiring... - Page 14 2. Connect station ESD ground wire pigtail. a. Strip 11 mm (7/16”) of insulation from the ends of the station ground wire pigtail, provided in the termination kit, and the incoming ground wire. ® b. Use one WAGO 221 Series LEVER-NUTS provided in the termination kit to connect the station ESD ground pigtail and the incoming ground.
-
Page 15: Install The E-Atc Into The Back Box
Install the E-ATC into the Back Box Receptacle spacers are provided to help align the station and cover flush against the wall in flush mount applications. The spacers are not required when installing the station into a surface mount back box. 1. -
Page 16: Install The Faceplate
Install the Faceplate The faceplate is secured to the station with built-in magnets. 1. Align the top of the faceplate to the station and angle the bottom approximately 20 degrees. 2. Hook the top of the faceplate to the tabs located on the electronics assembly. -
Page 17: User Interface Overview
User Interface Overview Keypad The user interface has an easy to use menu- navigation keypad that includes [UP], [DOWN], [BACK], and [ENTER] buttons. The [RECALL PRESET] and [HOLD] buttons are provided for everyday time clock operation. Pressing [UP], [DOWN], or [ENTER] will activate the main menu. Pressing the [RECALL PRESET] or [HOLD] buttons wakes the display and invokes the respective timeclock function. -
Page 18: Hold
Hold A Hold triggers an override to one or more scheduled events, allowing manual lighting control to persist. When a hold is active, regularly scheduled events are ignored and “-Schedule on Hold -” is displayed for the affected space. When an active hold is cleared, the originally scheduled event is restored. Without an active hold condition any manual lighting control will be replaced by the next scheduled event that occurs. -
Page 19: Recall Preset
The display indicates the affected space with a Timed Hold enabled. Both the space number and the time remaining are shown. If additional spaces have a Timed Hold enabled, the display will cycle through all spaces at two second intervals. Lighting Timeclock Lighting Timeclock Lighting Timeclock... -
Page 20: Main Menu
Main Menu The Main Menu provides access to set up and configure events, timeclock settings, Preset and Sequence controls, and Holiday Shut-Off settings. Main Menu Schedule Events Open/Close Settings Timeclock Settings Presets Holiday Shut-Off April 03, 2021 09:51am Schedule Events Main Menu Schedule Events Schedule Events... -
Page 21: Schedule An Event
interrupting action has completed and the hold timer lapses (hold timer is default is 120 minutes), or in the case of the While Closed setting, the Open event occurs. When the hold timer expires, the currently scheduled event executes. When a manual lighting control event occurs during an event, and Auto Timed Hold set to No, the events schedule is not placed on hold. -
Page 22: Open/Close Settings
10. Scroll to select When from the menu list and press [ENTER]. A list displays for selection of either a time of day or astronomical time settings. a. Scroll the listing and select the desired option. b. Press [ENTER] to accept the selection. 11. -
Page 23: Timeclock Settings
Timeclock Settings Timeclock Settings Time: 1:05 am Time Style: 12 hour Date: Apr / 3 / 2021 Hold Time: 120 min Flick Warn: Warn Time: 2 min Time Zone: GMT -6 Latitude: Longitude: 89 20 W DST: Manual DST Dates Restore Defaults The Timeclock Settings menu provides access to display preferences such as current Time and Time Style (12 hour or 24 hour clock), current Date,... -
Page 24: Change Current Date
Change Current Date 1. Select Date from the Timeclock Settings menu. 2. Press [ENTER] to modify the current selection. The Month field will display selected. 3. Use the [UP] or [DOWN] buttons to scroll to the current month and press [ENTER]. The Day field will display selected. 4. -
Page 25: Set Warn Time
Set Warn Time Warn Time is the amount of time before the TimeClock issues a scheduled Off action, preceding a Flick Warn. Factory default Warn Time is two minutes, but can be set to any value from 1-60 minutes. 1. Select Warn Time from the Timeclock Settings menu. 2. -
Page 26: Set Daylight Saving Time
Set Daylight Saving Time Set the current Daylight Saving Time (DST) location. Selecting an option from this menu list utilizes default Daylight Saving Time dates for the selected location. 1. Select DST from the Timeclock Settings menu. 2. Press [ENTER] to modify the current selection. 3. -
Page 27: Presets
The Presets menu provides access to manually activate, record, and deactivate host presets. The number of presets available is dependent on the product type. Elaho Relay Panel and the ETC Sensor IQ - up to 64 presets • ETC Unison DRd rack with E-ACP - up to 64 presets •... -
Page 28: Record A Preset
Record a Preset Before recording a new preset or recording over an existing preset, set the desired lighting look using Elaho Inspire or Preset stations, the product user interface, or an external DMX control source. Note: Recording a preset will affect the function of the button stations and other products in the system. -
Page 29: Holiday Shut-Off
Holiday Shut-Off The Holiday Shut-Off feature enables override of scheduled events (per individual space) for a specified period of time (1–7 days). The default override is set to 1 day. The Holiday Shut-Off feature is compliant with California Title 24. H o l i d a y S h u t - O f f Holiday Shut-Off H o l i d a y S h u t - O f f b e g i n s i n 5 : 0 0... -
Page 30: Change Default Shut-Off Time Duration
4. Press [DOWN] to cycle through the option of Unaffected or Shut- Off. 5. Press [ENTER] to commit the current selection. 6. Repeat steps 3 through 5 for all spaces you want to configure. Change Default Shut-Off Time Duration 1. Select Start Holiday Shut-Off from the Holiday Shut-Off menu and press [ENTER]. -
Page 31: Menu Flow Chart
Menu Flow Chart Lighting Timeclock Status Screen Saturday, Apr 03, 2021 9:51AM v3.3.4 Hold Screen Lighting Timeclock Variants Saturday, Apr 03, 2021 9:51AM -Schedule on Hold - Time remaining 1:31 Lighting Timeclock Saturday, Apr 03, 2021 9:51AM -Schedule on Hold - -in Space 1- Time remaining 1:31 Timed Hold... - Page 32 Astronomical TimeClock Configuration Manual...
- Page 33 Astronomical TimeClock Configuration Manual...
- Page 34 Astronomical TimeClock Configuration Manual...
- Page 35 Astronomical TimeClock Configuration Manual...
- Page 36 Corpora te He a dqua rte rs n Middleton, WI, USA | +1 608 831 4116 We b echoflexsolutions.com | E ma il info@echoflexsolutions.com | Support service@echoflexsolutions.com ©2021 Echoflex Solutions, Inc. Trademark and patent info: echoflexsolutions.com/ip Product information and specifications subject to change. Echoflex intends this document to be provided in its entirety. 8 1 8 6 M 1 2 3 0 -3 .3 .4 Rev A Released 2021-04...
Need help?
Do you have a question about the echoflex Elaho and is the answer not in the manual?
Questions and answers