Summary of Contents for WTI WTI-POE-I-ALT
- Page 1 Power Over Ethernet Power Injector WTI-POE-I-ALT Installation and Operation Manual REVISION 06/02/23...
-
Page 2: Table Of Contents
AC POWER LED WILL NOT TURN ON.................. 11 AC POWER LED ON – POE LINK OFF – OR POE LINK TURNS ON AND OFF ..11 DIMENSIONS ........................... 15 SPECIFICATIONS ........................... 16 WTI-POE-I -ALT WTI ~ Page 2 of 17... -
Page 3: Fcc Notice
Wireless Technology, Inc. (WTI) It is not to be copied or disclosed in undesired operation. any manner without the consent of READ THIS MANUAL Wireless Technology, Inc. (WTI). The... -
Page 4: Product Warranty And Repair
However, should you experience difficulty; you are protected under the provisions of this warranty. WTI warrants to the original user a product that is free of defects in materials and workmanship in normal use. WTI warrants to the original user that WTI’s products will be free of defects in materials and workmanship in normal use for a period of 12 months from the date of. -
Page 5: Repair Authorization
In no event shall WTI or its Authorized Dealers be liable for special or consequential damage arising from the use of this product, or any delay in the performance of this warranty due to causes beyond its control. - Page 6 Also take precautions to avoid contact between the equipment and other electrical wires or power sources that may be present at the installation site. WTI-POE-I -ALT WTI ~ Page 6 of 17...
-
Page 7: General Description
WTI Viper series VS720-H.264-HD30L-POE-XX and VS265-HD30L-POE- XX IP cameras. The WTI-POE-I-ALT will support up to 90 Watts of output power, which is the maximum power level supported by any device conforming to POE++ or IEEE 802.3bt standards of any CLASS or TYPE level. - Page 8 WTI-POE-I -ALT WTI ~ Page 8 of 17...
-
Page 9: Setup And Operation
STILL HAVE A FUNCTIONING POE POWER LINK. POWER SEQUENCING The DATA + POWER OUTPUT cable may be inserted before or after the WTI- POE-I-ALT power switch is turned on, as the POE controller IC will not apply power to the connected device without first ensuring that a proper POE connection is present. - Page 10 CABLING Between WTI-POE-I-ALT Power Injector and Powered Device 4 PAIR CONNECTIONS The WTI-POE-I-ALT power injector supplies power on all four pairs of the 8 Pin DATA + POWER OUTPUT connector. 56VDC RETURN is applied to pins 1, 2, 4 and 5 -56VDC POWER is applied to pins 3, 6, 7 and 8 100 Mbps Ethernet data transfer uses 2 pairs, normally on pins 1, 2, 3, and 6.
-
Page 11: Troubleshooting
This is the most difficult condition to troubleshoot, as it involves all parts of the system working correctly. The problem can be in the WTI-POE-I-ALT power injector or the camera (or other powered device) or in the cabling. The following troubleshooting list is in the order of most likely to least likely. - Page 12 If it is determined that the Ethernet cable and RJ-45 connectors all appear to be OK, and the Ohmmeter measurements appear good, then the next step is to try swapping out either the WTI-POE-I-ALT power injector or the camera. WTI-POE-I -ALT...
- Page 13 UNUSUAL PROBLEMS One unit that was returned to WTI for repair actually had crazy ants that had crawled into the unit and shorted out the high voltage section of the internal power supply.
- Page 14 WTI-POE-I -ALT WTI ~ Page 14 of 17...
-
Page 15: Dimensions
DIMENSIONS WTI-POE-I -ALT WTI ~ Page 15 of 17... -
Page 16: Specifications
Class 0 through Class 8 - Up to 90W (PD Type 3 and 4) IEEE 802.3at Class 0 through Class 4 – Up to 30W (PD Type 2) IEEE 802.3af Class 0 through Class 3 – Up to 15.4W (PD Type 1) WTI-POE-I -ALT WTI ~ Page 16 of 17... - Page 17 2/02/2021 – Initial Release 2/08/2021 – Changed “field Crimper” to crimper, changed warranty period to 1 year, changed WTI-POE-I to WTI-POE-I-ALT, Updated Table of Contents 6/02/2023 – Added detailed specifications for internal OEM power supply module regarding emissions radiation, emissions immunity, surge protection and various...
Need help?
Do you have a question about the WTI-POE-I-ALT and is the answer not in the manual?
Questions and answers