Table of Contents
Advertisement
Quick Links
Hover Blades® Owner's Manual
Unlock the secret power of your shop vacuum
NOTICE
Hover Blades must
only be used with
corded wet/dry
shop vacuums.
Cordless/battery
powered wet/dry
shop vacuums may
not deliver sufficient
airflow to power your
Hover Blades and
are therefore not
recommended.
IMPORTANT: PLEASE READ THIS FIRST
Airsled's comprehensive Hover Blades HOW-TO video
library demonstrates Hover Blades moving different
items, such as appliances and furniture. These videos
are purposely designed to answer the most frequent and
typical questions people have about Airsled's air-powered
products and technology. We recommend scanning the
QR code to access these videos for helpful information to
achieve optimal Airsled Hover Blades performance.
Patent Pending
Advertisement
Table of Contents
Summary of Contents for AIRSLED Hover Blades
- Page 1 Patent Pending IMPORTANT: PLEASE READ THIS FIRST Airsled’s comprehensive Hover Blades HOW-TO video library demonstrates Hover Blades moving different items, such as appliances and furniture. These videos are purposely designed to answer the most frequent and typical questions people have about Airsled’s air-powered...
-
Page 2: Table Of Contents
Connecting the Airsled Hover Blades to a Shop Vacuum with a 21/2”D Exhaust Port . . . . . . . . . . . . . - Page 3 THESE WARNINGS COULD RESULT IN SERIOUS INJURY. WARNING! WARNING! READ ALL MANUALS, WARNINGS, AND LABELS PRIOR TO USING THIS PRODUCT. A irsled Hover Blades have the ability to move a variety of objects provided that l WARNING! WARNING! ELECTRICAL the appropriate conditions exist, and the load’s weight is within the system’s maximum lifting capacity .
-
Page 4: What Is Included
WHAT IS INCLUDED AIRSLED HOVER BLADES COMPONENTS AND PARTS LIST YOUR AIRSLED HOVER BLADES INCLUDE THE FOLLOWING PARTS DEPENDING ON WHICH SIZE YOU PURCHASED. TO CONNECT THE HOVER BLADES TO YOUR SHOP VACUUM SEE PAGE 7. Part No. Description Comments PA0736 7”... -
Page 5: Minor Product Variances That Are Normal
Minor Product Variances Due to the Hand-made Nature of Airsled Systems Airsled Hover Blades are made by hand to exacting specifications . Because each air beam is made by hand, you may see very minor differences in how the rubber fabric is folded and glued around the aluminum at the edges . You may also notice some glue residue on the aluminum and/or rubber fabric . -
Page 6: General Safety And Use Information
Manufacturers offer many types of shop vacuums with different airflow ratings measured in cubic feet per minute (CFM). Based on Airsled’s research and testing, the CFM rating of a shop vacuum is the key specification for determining how much lift can be achieved when connecting the shop vacuum to the Airsled Hover Blades. -
Page 7: Positioning The Hover Blades Air Beams
Load Center the Air Beams for Optimal Hover Blades Performance (including the impact of weight distribution) O ptimal Hover Blades performance will be achieved by centering the air beams under the load so that the same length of air l beam extends from the front and the back . -
Page 8: Connecting The Airsled Hover Blades To A Shop Vacuum With A 21/2"D Exhaust Port
IMPORTANT NOTE FOR ALL SHOP VACUUMS OPENINGS WILL NOT WORK Take these steps for proper operation of your Hover Blades otherwise they will not work properly and airflow out the exhaust will be significantly reduced: 1) dust bag must be removed before use;... -
Page 9: Less Than 21/2"D
Airsled Universal will help prevent is from inadvertently springing open during use. Iris Adapter 3) Firmly press the Hover Blades hose into the hard plastic end of the universal adapter to complete the connection . Shop vacuum shown with hose... -
Page 10: Special Safety And Use Considerations
. In such cases, it is possible that the weight, especially if at the upper limit of the Hover Blades' lift rating, can impact airflow into the air bladder and therefore prevent air beam inflation . If this happens, you may need to use your body/arm strength to help “nudge”... -
Page 11: Using Your Body And Foot To Control Tilting
Tilting may occur if the load is not optimally positioned over the air beams (e .g ., object is up against a wall and air beams only extend slightly through the rear) . If the load tilts away from you, you can use the Airsled foot brace accessory by laying it across the front of the air beams and applying downward pressure with your foot . -
Page 12: Moving Objects On Very Narrow Feet/Legs
Hover Blades are designed to move appliances and comparably sized loads and include either the standard 7 inch wide x 36 inch long or 9 inch x 36 inch air beams based on the Hover Blades you purchased . The Hover Blades include a set of 16 inch long supply hoses which are recommended for loads with a base that does not exceed 32 inches . -
Page 13: Care And Maintenance
P lease refer to the Aisled One-Year Limited Warranty for information regarding the product warranty . l F or normal wear and tear damage to your Airsled Hover Blades, which is not covered by the One-Year Limited Warranty, the l following information applies: Airsled offers refurbishment services that can restore your aluminum air beams to as-new condition . - Page 14 D amage or failure caused by normal wear and tear; l D amage or failure caused by improper use of the Airsled Hover Blades, which includes a failure to use the Airsled Hover Blades in l accordance with the instructions in the Owner’s Manual;...
-
Page 15: Warranty
Authorization Form and receive a Sales Return Order (SRO) authorization from Airsled in order to ship your Airsled Hover Blades to the Airsled, Inc. at the address shown below within 30 days of receiving your product. All return shipping costs are to be paid by you, the customer, not Airsled. - Page 16 Airsled, Inc. 66 Albe Dr. Newark, DE 19702 800-AIRSLED (800-247-7533) www.airsled.com...
Need help?
Do you have a question about the Hover Blades and is the answer not in the manual?
Questions and answers