1. Manuals
  2. Brands
  3. Mikroe Manuals
  4. Network Hardware
  5. PLANET DEBUG
  6. User manual

Mikroe PLANET DEBUG User Manual

Hide thumbs

Advertisement

Table of Contents

Time-saving embedded tools

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PLANET DEBUG and is the answer not in the manual?

Questions and answers

Summary of Contents for Mikroe PLANET DEBUG

  • Page 1 Time-saving embedded tools...
  • Page 2 PC INDEPENDENT HARDWARE EMBEDDED REMOTE PROGRAMMING / DEBUGGING WITH LIVE STREAMING...

  • Page 3: Table Of Contents

    Table of content Installation requirements Setup Assembly Network Configuration CODEGRIP/Board Configuration Camera Configuration Setup Testing and Configuration P L A N E T D E B U G A s s e m b l y G u i d e...
  • Page 4 This document should give you an insight into what is needed network parameters, and settings that need to be provided/set for one Planet Debug Setup to be installed and connected to the on the hardware, as well as on the MIKROE licensing portal.

  • Page 5: Installation Requirements

    INSTALLATION REQUIREMENTS For Planet Debug to be installed in a specific location, the following conditions must be met on the Client (physical host and connection provider) side: Business requirements: Network requirements: ¬ Setup must be turned ON 24/7 To enable communication with setup devices ¬...

  • Page 6: Setup Assembly

    SETUP ASSEMBLY What's in the package - Planet Debug P L A N E T D E B U G A s s e m b l y G u i d e...
  • Page 7 Step 1: Metal Frame Base Step 2: Mounting necessities The Planet Debug metal frame cell consists of elements that are Connect 12V power adapter to the 12VDC input of the combined in precise order. You will get all the necessities in a development board.
  • Page 8 Position the plate first in the part where the fenders are and then Connect 12V power adapter to the 12VDC input of the development board, but also pay attention to the cable management and place it in gently push it in place and it will be locked to. The fiinal adjustment should be made at the end when you have a video stream.
  • Page 9 Step 3: Lighting Step 4: IP Camera placement An essential element of the video stream is good lightning. Place To fix the Axis M1137 IP camera onto the metal frame, we will the light strips inside the metal frame base, located in front of only use the only screw inside the package box instead of using the board mounting section.
  • Page 10 12VDC adapter, light 12VDC adapter, PoE switch adapter, and WiFi AP to the extension cord before connecting it to the wall. With this setup, MIKROE will provide an extension cord along with a US wall adapter if needed. P L A N E T D E B U G A s s e m b l y G u i d e...
  • Page 11 Fully assembled Planet Debug frame P L A N E T D E B U G A s s e m b l y G u i d e...

  • Page 12: Network Configuration

    NETWORK CONFIGURATION Access point To establish a network connection for development board and IP camera, you will need devices PoE Switch and Access Point connected. They are included in the package, PoE Switch Tenda The development board has a network connection over the WiFi. TEF1106P-4-63W, and Tenda A301 WiFi.
  • Page 13 To use and access the development board from the NECTO Studio IDE through the WiFi, you will need to enable WiFi and SSL licenses. Download the CODEGRIP Suite application from the link https://www.mikroe.com/setup/codegrip and follow installation steps. Check for updates 1.
  • Page 14 Check for CODEGRIP updates 1. Connect the CODEGRIP with a PC using the USB-C cable. If everything was connected properly, POWER, ACTIVE and USB LINK LED indicators on the CODEGRIP device should be ON. 2. Under CODEGRIP tab follow instruction on how to detect CODEGRIP device in a bootloader mode.
  • Page 15 Select CODEGRIP device 1. Open the CODEGRIP menu button and select the newly unfolded Scanning menu item. 2. Click on the SCAN DEVICES button to get a list of available CODEGRIP devices. 3. To connect with your CODEGRIP over a USB cable, click the USB Link button.
  • Page 16 Activate licenses Some features of the CODEGRIP such as the functionality of the WiFi module, and the SSL security, require licensing. If no valid license is found, these options will be unavailable in the CODEGRIP Suite. Open the CODEGRIP menu and select the newly unfolded License menu item (2).
  • Page 17 Once the licensing process is successfully completed, the licenses will be permanently stored within the CODEGRIP device. For WiFi license, please visit www.mikroe.com/codegrip-wifi-license For SSL security license, please visit www.mikroe.com/codegrip-ssl-license P L A N E T D E B U G A s s e m b l y G u i d e...
  • Page 18 Configure WiFi general options 1. Open the CODEGRIP Menu button and select the newly unfolded Configuration Menu item. 2. Open tab WiFi General and set configuration as shown in the image below. P L A N E T D E B U G A s s e m b l y G u i d e...
  • Page 19 Configure WiFi mode options Open tab WiFi Mode and fill in the fields under the Station Mode section: SSID Password: If the WiFi network to which the connection is attempted requires a password, it can be specified in this field. Secure type: The security protocol selected here must match the security protocol used on a WiFi network to which the connection is attempted.

  • Page 20: Camera Configuration

    CAMERA CONFIGURATION Setup Installation Before you access the camera, you will need to install AXIS IP Utility After mount, connect the IP camera to PoE Switch (ports 1-4) if you from this link: haven'd done so already. Greenlight is the sign of a connected and https://www.axis.com/support/downloads/axis-ip-utility Assign the IP address 1.
  • Page 21 Configuration Settings Now you can access the IP camera. You can do it by putting the IP Important - Before you proceed, it’s necessary to allow anonymous address directly in the web browser or by AXIS IP Utility (double-click access to the IP Camera or right-click on a device - View Home Page).
  • Page 22 Camera adjustment 1. Focus ring To make a development board visible, you would need to adjust focus 2. Focus ring lock and zoom. Follow these steps: 3. Zoom puller 1. If you didn’t, place the IP camera into the metal frame field and development board to the magnetic field (opposite of the IP 3.
  • Page 23 From the bottom menu, on the lower right corner, click settings and set the following: IMAGE TAB AUDIO TAB Contrast - 55 Allow audio - turn OFF Sharpness - 60 Orientation (if you didn’t change on initial configuration) - 180 degrees TCP/IP - Skip this step if you set static IP address by AXIS IP Utility Light environment - Fixed - fluorescent 1 1.

  • Page 24: Setup Testing And Configuration

    CODEGRIP and IP camera, and port and IP configuration of the network, the final step is adding all parameters to the NECTO To complete your Planet Debug setup, in this case Studio License Portal and testing them. development board and IP camera, to be accessible from...
  • Page 25 Development board properties Besides adding IP addresses and ports to the license portal, MIKROE will need information about development board configuration such as onboard MCU (with crystal oscillator if it is exchangeable) or MCU card, add-on boards and their exact position, display, LCD.
  • Page 26 (including damages for loss of business profits and business information, business interruption or any other pecuniary loss) arising out of the use of this manual or product, even if MIKROE has been advised of the possibility of such damages. MIKROE reserves the right to change information contained in this manual at any time without prior notice, if necessary.
  • Page 27 If you want to learn more about our products, please visit our website at www.mikroe.com/planet-debug If you are experiencing some problems with any of our products or just need additional information, please place your ticket at www.mikroe.com/support If you have any questions, comments or business proposals, do not hesitate to contact us at office@mikroe.com...

Table of Contents