Do you have a question about the AE018 Series and is the answer not in the manual?
Questions and answers
Karl Krupp
February 4, 2025
How can i run the construction up after i restarted the engine.
1 comments:
Mr. Anderson
February 10, 2025
The context does not provide specific instructions on running the construction on the SMS AE018 Series after restarting the engine. However, it mentions setting motors to zero, which may be necessary after restarting. Try setting the motors to zero by following the instructions related to "Set motors to zero" and "UP DOWN" sequences in the manual. If further details are required, refer to the complete manual.
SMS Projector Short Throw Mobile Motorized How to read this manual Symbols: Simboli: 1. Important symbol denotes measures/information that it is important 1. Simbolo importante che indica misure/informazioni importanti da seguire. to follow. 2. Simbolo del triangolo indica una situazione che richiede attenzione.
SMS Projector Short Throw Mobile Motorized Instructions for use Caution Caution! Risk of crushing Attenzione! Rischio di schiacciamento ¡Precaución! Riesgo de aprisionamiento Caution Caution Attention ! Risque d'écrasement Achtung! Risiko des Zerquetschens Varoitus! Puristumisvaara Voorzichtig! Beknellingsgevaar Uwaga! Ryzyko przygniecenia DOWN DOWN Внимание! Возможный...
Page 4
Advertencia Avertissement El montaje del producto no es responsabilidad de SMS Smart Media Solutions AB y es muy Le montage doit impérativement être effectué de façon correcte et ne relève pas de la importante que el producto sea montado correctamente. El montaje incorrecto puede responsabilité...
Page 5
Sulla ricevuta devono essere chiaramente leggibili nome be clearly legible on the receipt. The owner is to pay the cost of returning the product to SMS, while del fornitore e data d’acquisto. Le spese di spedizione a SMS sono a carico dell’acquirente;...
SE-131 30 Nacka SE-131 30 Nacka Suède Sweden Sweden atteste par la présente que le produit : SMS Projector versichert hiermit, dass:SMS Projector Short Throw Vakuuttaa täten, että: SMS Projector Short Throw Short Throw Wall Motorized Wall Motorized Wall Motorized, modèle AE019...
Page 7
SMS Projector Short Throw Mobile Motorized (x4) (x4) (x2) (x2) not used (x4) M6x30, not used (x4) (x2) M8x16, not used (x4) (x4) (X2) (X2) (x2) (x4) 1390 (x2) (x2) (x8) (x4) (x2) Alternative (x8) (x4) (x4) not used (x3-4)
Page 8
SMS Touch Wall-Floor Motorized 13 mm (x2) Max 8 kg Dimension Tightening torque Tightening torque 3.3 Nm 6.5 Nm Max 50 kg 11.1 Nm Set motors to zero...
Page 9
SMS Projector Short Throw Mobile Motorized Caution Caution Caution DOWN DOWN DOWN 5 sec 5 sec 2 sec Caution Caution Caution DOWN DOWN DOWN =Set to zero 5 sec 5 sec 2 sec (13 mm) (x4) Not used Not used...
Page 10
SMS Projector Short Throw Mobile Motorized (x4) (x8) 11.1 Nm 11.1 Nm Front OPTIONAL Lock 11.1 Nm (x8) 11.1 Nm 6.5 Nm...
Page 11
SMS Projector Short Throw Mobile Motorized (x2) (x2) (x4) (x4) (x4) y (mm) 13 mm...
Page 12
SMS Projector Short Throw Mobile Motorized OPTIONAL No. 3...
Page 13
SMS Projector Short Throw Mobile Motorized...
Page 14
SMS Projector Short Throw Mobile Motorized (x4)
Page 15
SMS Projector Short Throw Mobile Motorized...
Page 16
SMS Projector Short Throw Mobile Motorized (x4)
Page 17
SMS Projector Short Throw Mobile Motorized SMS Projector Short Throw Mobile Motorized Dimensions (in mm) A = Board height B =Vertical projection distance C = A + B Min C: 1150 Max C: 1650 Max board width: - 1100 Max board depth: 100...
Page 18
6.5 Nm 11.1 Nm (x2) Alternative (x4) not used Disclaimer: We reserve the right to change the design and technical data without prior notice. www.SmartMediaSolutions.se SMS Smart Media Solutions AB, Hästholmsvägen 32, SE-131 30 Nacka, +46 (0)8 448 26 60...
Need help?
Do you have a question about the AE018 Series and is the answer not in the manual?
Questions and answers
How can i run the construction up after i restarted the engine.
The context does not provide specific instructions on running the construction on the SMS AE018 Series after restarting the engine. However, it mentions setting motors to zero, which may be necessary after restarting. Try setting the motors to zero by following the instructions related to "Set motors to zero" and "UP DOWN" sequences in the manual. If further details are required, refer to the complete manual.
This answer is automatically generated