Table of Contents
Advertisement
Quick Links
IDSL Termination Unit Module
IDSL1 1050/IDSL4 1052
T A I N E T C O M M U N I C A T I O N S Y S T E M C O R P .
Headquarters:
No. 25, Alley 15, Lane 120, Sec. 1. Nei-Hu Rd,
Taipei 114, Taiwan
TEL: 886-2-26583000
FAX: 886-2-26583232
V1.0
TAINET
MARS 9000
Operation Manual
T h e P r o f e s s i o n a l P a r t n e r
007007-0490
Beijing Branch:
Room 409, Everlast Plaza, No.39 Anding Road, Chaoyang
District, Beijing, 100029, China
Tel: 86-10-64449830 ~ 1
Fax: 86-10-64449832
4/20/2000
Advertisement
Table of Contents
Summary of Contents for Tainet MARS 9000
- Page 1 TAINET MARS 9000 IDSL Termination Unit Module IDSL1 1050/IDSL4 1052 Operation Manual T h e P r o f e s s i o n a l P a r t n e r T A I N E T C O M M U N I C A T I O N S Y S T E M C O R P .
-
Page 3: Table Of Contents
Contents CHAPTER 1 INTRODUCTION 1.1 Functional Description ............. 1-2 1.2 Technical Information .............. 1-2 1.3 Technical specifications ............1-3 1.4 Hardware description ............... 1-4 1.4.1 IDSL1................1-4 1.4.2 IDSL4................1-5 CHAPTER 2 INSTALLATION 2.1 Installing IDSL1/4 module............2-2 2.2 Configuring IDSL1/4 parameters..........2-3 2.3 Supervisory Interface: LCD front panel........ - Page 4 Figure Figure 1-1 IDSL1 1050 Faceplate................1-4 Figure 1-2 IDSL4 1052 Faceplate................1-5 Figure 2-1 Module insertion..................2-2 Figure 2-2 Organization of 1050’s front panel menu tree.......... 2-6 Figure 2-3 Organization of 1052’s front panel menu tree.......... 2-7 Figure 2-4 Local Analog Loopback path..............2-10 Figure 2-5 1050 Local Digital Loopback path............
-
Page 5: Chapter 1 Introduction
Chapter 1 INTRODUCTION Overview 1.1 Functional Description 1.2 Technical Information 1.3 Technical specifications 1.4 Hardware description 1.4.1 IDSL1 1.4.2 IDSL4... -
Page 6: Functional Description
2.4K/4.8K/9.6K/19.2K/38.4K/64Kbps/128Kbps, and ASYNC rates supported are 0.3K/0.6K/1.2K/2.4K/4.8K/9.6K/19.2K/38.4Kbps (ASYNC mode is only available while both end of data path is terminated by Tainet NTUs). Data rates at 64Kbps and below (SYNC & ASYNC) occupy one time slot of MARS 9000 TDM buses, and 128Kbps requires two time-slot to transport payload between tributaries and aggregate links. -
Page 7: Technical Specifications
INTRODUCTION Technical specifications • Data rate Synchronous 2.4K/4.8K/9.6K/19.2K/38.4K/64K/128K bps Asynchronous 0.3K/0.6K/1.2K/2.4K/4.8K/9.6K/19.2K/38.4K bps • Line requirement Single or dual pair of unconditioned unloaded twisted copper wire • Loop reach Up to 6.0Km over 26 gauge pair Up to 7.8Km over 24 gauge pair •... -
Page 8: Hardware Description
INTRODUCTION Hardware description 1.4.1 IDSL1 The IDSL1 can be installed in any slot of TRS-32M. The outlook and description of faceplate are shown below: LED indicators Selection indicator RED = Selected selected by LCD OFF = Not selected IDSL1 front panel GREEN = Active state Link state OFF = Link unavailable... -
Page 9: Idsl4
INTRODUCTION 1.4.2 IDSL4 The IDSL4 can be installed in any slot of TRS-32M. The outlook and description of faceplate are shown below: LED indicators Selection indicator RED = Selected Selected by NMC OFF = Not selected Indicator of polling Blinking if polled SCAN activity by NMC... - Page 10 INTRODUCTION...
-
Page 11: Chapter 2 Installation
Chapter 2 INSTALLATION Overview 2.1 Installing IDSL1/4 module 2.2 Configuring IDSL1/4 parameters 2.3 Supervisory Interface: LCD front panel 2.4 IDSL1/4 menu tree 2.4.1 IDSL link parameters - Group name : CONFIG NTU 2.4.2 Factory default profiles - Group name : PROFILE 2.4.3 Loopback and diagnostic functions - Group name : TEST 2.4.4... -
Page 12: Installing Idsl1/4 Module
If the NO SCAN problem can’t be resolved or you have trouble installing the card, please contact with your local dealer for technical support. Or call TAINET post- sale department directly by 886-2-26583000. -
Page 13: Configuring Idsl1/4 Parameters
INSTALLATION Configuring IDSL1/4 parameters The easiest way to set up IDSL1/4 is to load the factory profile. It covers almost all possible configurations when using this module. For loading a profile, read section 2.4.2 for operation on profile. l LCD front panel of MARS9000: Full functional menu tree driven system. -
Page 14: Supervisory Interface: Lcd Front Panel
Control Mode : Tells operator if the local or remote unit is under control by front panel. If the CPE is TAINET DT-128, remote control function can also be accomplished via local LCD panel. When DT-128 is responding for remote-control-request (initiated by operator), this field will show ‘(Remote)’. - Page 15 INSTALLATION • CONNECT Synchronized (connected) with CPE • Handshake Handshaking with CPE • Disconnect Drop current connection • (AL) Analog Loopback test on going • (DL) Digital Loopback test on going • (RDL) Remote Digital Loopback test on going • (RDL+TP) Remote Digital Loopback and Test Pattern test on going Information for operators...
-
Page 16: Idsl1/4 Menu Tree
INSTALLATION 2.4 IDSL1/4 menu tree Higher level NMC options LY SYNC (Local) 128K Handshake STATUS Retries=00000 Clear All AL (2W Only) ON/OFF ON/OFF TEST ON/OFF Test_Pattern ON/OFF Error Count LT-external NT-loopback LT/NT Mode LT-internal CONFIG NTU LINE Type 4W Att16db SYNC-128K SYNC-64K SYNC-38.4K... - Page 17 INSTALLATION V E R S I O N M E N U S E L E C T 0 : A L L 1 2 8 K S T A T U S 1 : A L L 6 4 K L O A D 2 : 1 - 2 1 2 8 K , 3 - 4 6 4 K 3:1-2...
-
Page 18: Idsl Link Parameters - Group Name : Config Ntu2-8
INSTALLATION 2.4.1 IDSL link parameters - Group name : CONFIG NTU Configurable objects: Below are functional descriptions for all configurable objects in ‘CONFIG NTU’ group. Refer to table 2-1 for all available options. LINE Type: Sets the line type of IDSL. Subscriber loop defined in T1.601 is only single loop (two-wire). -
Page 19: Factory Default Profiles - Group Name : Profile
INSTALLATION 2.4.2 Factory default profiles - Group name : PROFILE Available objects: This group contains only one function for loading profile. Load: Reset system with pre-defined factory profiles. Detailed information for each profile is listed in table 2-2. Table 2-2 1050 Load list 0:LT-SYNC- 1:NT-SYNC- 2:LT-SYNC-... -
Page 20: Loopback And Diagnostic Functions - Group Name
INSTALLATION 2.4.3 Loopback and diagnostic functions - Group name : TEST Configurable objects: Below are functional descriptions for all available loopback objects in ‘TEST’ group. Refer to table 2-5 for all available options. AL(2W only): Loopback analog path within transceiver in the direction toward TDM bus. -
Page 21: Test
INSTALLATION RDL: Request NT to loopback digital data path within framer in the direction toward MARS 9000 TDM bus. To LT TDM bus TDM bus To NT TDM interface Line interface Line interface TDM interface Loopback path Loop wire Figure 2-7 Remote Digital Loopback path RDL Grant: Grant RDL request initiated by remote site (NT). -
Page 22: Dte
INSTALLATION 2.4.4 TDM interface parameters - Group name : CONFIG DTE Configurable objects: This group contains all TDM interface parameters. Data Rate/Format: Select IDSL link rate. E1 Sel: Select aggregate link for IDSL link traffic. Both 64Kbps channels will be aggregated to this selected E1. -
Page 23: System Statistics Functions - Group Name : Status
INSTALLATION 2.4.5 System statistics functions - Group name : STATUS System statistics objects: This group contains a counter that counting the numbers of link re-negotiation. Retries : IDSL link re-negotiation count statistics. Table 2-8 1050 Status Available Object name Description Message Retries = Retries=xxxxx Number of re-negotiation count... -
Page 24: The Connections For The Rear Panel (Trs-32 Daughter Board)
INSTALLATION 2.4.6 The connections for the rear panel (TRS-32 Daughter Board) e.g: plug the 1052 to slot 1: 4W/RX 2W/TX PORT1 PORT2 4W/RX 2W/TX CH17 PORT3 PORT4 4W/RX 2W/TX 4W/RX 2W/TX CH18 Figure 2-8 TRS-32 Daughter Board 2-14...
Need help?
Do you have a question about the MARS 9000 and is the answer not in the manual?
Questions and answers