Summary of Contents for GameKeeper HU2284601-GK
- Page 1 This Owner's Manual is provided and hosted by Appliance Factory Parts. Rankam HU2284601-GK Owner's Manual Shop genuine replacement parts for Rankam HU2284601-GK Find Your Rankam Grill Parts - Select From 123 Models -------- Manual continues below --------...
- Page 2 100 LB WILDLIFE FEEDER Assembly and Operating Instructions Model # HU2284601-GK 1 of 21 HU2284601-GK - ENG 20180502-V1.0...
-
Page 3: Pay Attention
Wrench etc….. DANGER Your GameKeeper Feeder is designed, engineered and constructed in a manner that makes it a rugged piece of hunting equipment that will give you years of service. This rugged construction makes your feeder physically heavy. As such, you should never attempt to assemble this feeder alone. YOU MUST HAVE A MINIMUM OF TWO (2) ADULTS FOR THE SAFE ERECTION OF YOUR FEEDER. - Page 4 GENERATORS, SUBSTATIONS, ETC) AND/OR TRANSMISSION EQUIPMENT (POWER LINES). FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR DEATH! DO NOT LOAD FEED WITHOUT ANOTHER ADULT. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR DEATH! 3 of 21 HU2284601-GK - ENG 20180502-V1.0...
- Page 5 PRIOR TO THE FIRST TIME OF OPERATION. ALWAYS REFER TO THE USER GUIDE OF THE BATTERY FOR DIRECTION. THE PROPER SPACING BETWEEN THE SPIN PLATE AND THE FUNNEL IS 3/8 INCH. THIS IS VERY IMPORTANT FOR SERVICE FREE OPERATION. 4 of 21 HU2284601-GK - ENG 20180502-V1.0...
- Page 6 FOR REPLACEMENT OF MISSING OR DEFECTIVE PARTS. Symbol: The following symbols will be shown in assembly procedures for indication of tightening the bolt and nut if necessary. Hand Tighten only at this time Tighten with tools at this time 5 of 21 HU2284601-GK - ENG 20180502-V1.0...
- Page 7 Product Diagram TK11 TK13 TK12 TK14 6 of 21 HU2284601-GK - ENG 20180502-V1.0...
- Page 8 40 pcs (M8x15) Locking Nut (M8) 44 pcs Flat Washer (M8) 84 pcs Hex. Bolt 4 pcs (M6x20) Locking Nut (M6) 4 pcs Camera Mounting 2 pcs Bolt Flat Washer 4 pcs (M6) 7 of 21 HU2284601-GK - ENG 20180502-V1.0...
- Page 9 Hardware List – For Timer Kit Item Item Name Diagram Hex. Bolt 10 pcs (M6x20) Flat Washer 2 pcs (M6) Butterfly Nut 2 pcs (M6) Flange Nut 2 pcs (M6) Wing Bolt 1 pc 8 of 21 HU2284601-GK - ENG 20180502-V1.0...
- Page 10 #D - 32 pcs Step 2. Attach Feet (#6) to leg assemblies in Step #1. Hand tighten bolts only! Hardware required: #B - 8 pcs #C - 8 pcs #D - 16 pcs 9 of 21 HU2284601-GK - ENG 20180502-V1.0...
- Page 11 #3 (front and rear) on this side (4 pcs) Leg #3 Under leg bracket of hopper for assembly Leg #3 On Top of leg bracket of hopper for assembly 10 of 21 HU2284601-GK - ENG 20180502-V1.0...
- Page 12 Step 5. Assembly of Timer Kit. Hand tighten bolts Hardware required: TK13 #M - 2 pcs #N - 2 pcs #P - 2 pcs #Q - 2 pcs #R - 1 pc TK12 11 of 21 HU2284601-GK - ENG 20180502-V1.0...
- Page 13 Step 6. Attach Timer Kit to Hopper. Adjust Spin Plate to funnel distance to 3/8”. Tighten bolts with tool Hardware required: #M - 4 pcs spin plate Door of timer box Notes: Door of Timer Box faces out (side of hopper) Adjust Spin Plate to funnel distance to 3/8” 12 of 21 HU2284601-GK - ENG 20180502-V1.0...
- Page 14 Step 8. Attach a Camera Mounting Bracket (#8) to Hopper. User may attach another Camera Mounting Bracket in the same manner. Hardware required: #B – 4 pcs #C – 4 pcs #D – 4 pcs #G – 2 pcs 13 of 21 HU2284601-GK - ENG 20180502-V1.0...
- Page 15 Step 9. Put the lid on hopper body and lock it. Affix the feeder to the ground with Stakes (#5). … YOUR FEEDER IS COMPLETELY ASSEMBLED, 14 of 21 HU2284601-GK - ENG 20180502-V1.0...
- Page 16 DO NOT LOAD FEEDER UNTIL IT IS STANDING UP AND IN PLACE. THE PROPER SPACING BETWEEN THE SPIN PLATE AND THE FUNNEL IS 3/8 INCH. THIS IS VERY IMPORTANT FOR SERVICE- FREE OPERATION. 15 of 21 HU2284601-GK - ENG 20180502-V1.0...
- Page 17 REGULATIONS. PLEASE ALWAYS KEEP YOUR INFORMATION UP-TO-DATE AND RELIABLE. MANY STATE LAWS CHANGE AND ARE AMENDED WITHOUT NOTICE. ALWAYS DOUBLE CHECK YOUR STATE AND SPECIFIC COUNTY FEEDING LAWS REGARDING THE USE OF FEEDERS. 16 of 21 HU2284601-GK - ENG 20180502-V1.0...
- Page 18 DO NOT LOAD FEEDER UNTIL IT IS COMPLETELY ASSEMBLED AND STANDING UP IN PLACE. DO NOT LOAD THE FEEDER IF YOU FIND ANY OF PART #5 (STAKES) MISSING, DAMAGED AND/OR LOOSE. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR DEATH! 17 of 21 HU2284601-GK - ENG 20180502-V1.0...
-
Page 19: How To Install Battery
CONNECTING THE BATTERY IN ANY OTHER WAY WILL PERMANENTLY DAMAGE YOUR UNIT. TAKE EXTREME CARE TO MAKE THIS CONNECTION PROPERLY. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS INJURY OR DEATH. 18 of 21 HU2284601-GK - ENG 20180502-V1.0... -
Page 20: How To Operate The Timer
INJURY. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: - THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE. - THE DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. 19 of 21 HU2284601-GK - ENG 20180502-V1.0... - Page 21 Please contact Customer Service at Rankam (China) Manufacturing Company Limited 1-888-837-1380 Monday thru Friday 8 A.M. to 5 P.M. Pacific Standard Time or by email customerservice@rankam.com WE CAN HELP. Made in China 20 of 21 HU2284601-GK - ENG 20180502-V1.0...
- Page 22 Follow the Customer Service Representative’s instructions exactly. If a return is necessary, it must be packed carefully and shipped prepaid. Rankam (China) Manufacturing Company Limited 18 F., New Lee Wah Centre 88 Tokwawan Road, Kowloon, Hong Kong 21 of 21 HU2284601-GK - ENG 20180502-V1.0...
Need help?
Do you have a question about the HU2284601-GK and is the answer not in the manual?
Questions and answers