Subscribe to Our Youtube Channel
Related Manuals for THORENS TD202
Summary of Contents for THORENS TD202
- Page 1 TD202 BEDIENUNGSANLEITUNG USER GUIDE MANUEL D’UTILISATION РУКОВОДСТВО ПОЛЬЗОВАТЕЛЯ 使用手册 16 USER GUIDE...
- Page 2 FEATURES / TOP PANEL...
- Page 3 01. Counterweight The counterweight is used for precise adjustment of the stylus pressure on the vinyl, to properly balance the tonearm. 02. Anti-Skating Control To set the anti-skating force of the tonearm. 03. Tone arm Lever Use this lever to lower and raise the tonearm. 04.
-
Page 4: Grounding Terminal
10. Grounding terminal A direct electrical connection to the earth 11. RCA JACKS selector Plug in the RCA cable, and connect the cable to the audio amplifier 12. Pre Amp ON/OFF selector ON: Connect the RCA cable to the LINE-IN terminal of the amplifier. OFF: to stop the LINE-IN terminal of the amplifier. -
Page 5: Power Supply Jack
13. USB Port Use the USB cable to connect from your turntable to your computer. 14. Power Supply Jack To connect the power cable for power supply 15. Power Switch To turn the unit On/Off 20 REAR PANEL... -
Page 6: Dust Cover Installation
DUST COVER INSTALLATION 01. Unwrap the two hinges and the dustcover. 02. Note that the hinges have a clamp side and a tab side. 03. Note that the dustcover has two spots on its rear edge shaped to accept the clamps. 04. -
Page 7: Mains Connection
10. The scale indicates the stylus pressure in grams. The pressure of the cartridge supplied with this turntable is 2.0g, turn the entire counterweight counter-clockwise to “2” and the anti-skating to “2“. If a different cartridge is used, adjust the stylus pressure and the antiskating indicated to the corresponding specifications. MAINS CONNECTION An external switching power adaptor is supplied with this turntable. -
Page 8: To Replace The Stylus
TO REPLACE THE STYLUS • Put the rest clip on the pick-up arm. • Remove the protective cap from the stylus. • Pull the stylus to the lower front and remove it. • Put in the new stylus following the reverse procedure. •... - Page 9 We would also point out that for the same reason your stylus should be replaced periodically (approximately every 250 hours). Dust the stylus from time to time using a very soft brush dipped in alcohol (brushing from back to front of the cartridge). WHEN TRANSPORTING YOUR RECORD PLAYER DO NOT FORGET TO: Replace the protective cap on the stylus.
- Page 10 Turntable section Drive System Belt Drive Motor DC Motor Speed 33 1/3 RPM, 45 RPM Rotation Speed Variation +/–2% Wow and Flutter 0.2% 67dB or higher (A-weighted, 20kHz LPF) Signal-to-Noise Ratio 60dB or higher (unweighted, 20kHz LPF) Platter Aluminum Die-cast Diameter of Platter 12“, 300mm Specification...
-
Page 11: Tonearm Section
Tonearm section Alumi tube Type Static Balance, Straight Effective Arm Length 8.8“, 223.6mm Stylus Pressure Range 0 to 4g Supported Cartridge Weight 3.5 bis 6.0g Overhang 18.6mm Anti-skating Adjustment Supported Specification... -
Page 12: Cartridge Section
Cartridge section Type MM type (Audio-Technica AT-95E) Stylus Construction Bonded Diamond Frequency Response 20Hz to 20kHz Channel Separation >18dB Channel Balance 2.5dB Vertical Tracking Angle 20 degrees Supported Load Impedance 47k ohms Output Voltage 2.5mV (1kHz, 3.54cm/sec.) Stylus Pressure 2.0g +/–0.5g Cartridge Weight 5.7g +/–0.5g Head-shell Weight... -
Page 13: Analog Output
Analog Output Connector RCA Pin jack (Gold-plated) Power AC 100 to 240V, 50/60Hz Power Consumption 1.5W (less than 0.5W at Standby) Overall Dimensions (W x D x H) 420 x 355x 141mm Weight Approx. 3.9 kg Specification... - Page 14 Thorens GmbH Lustheide 85 · 51427 Bergisch Gladbach · Deutschland www.thorens.com · info@thorens.com www.thorens.com...
Need help?
Do you have a question about the TD202 and is the answer not in the manual?
Questions and answers