golmar EASYGATE-RF Installation Manual
  1. Manuals
  2. Brands
  3. golmar Manuals
  4. Controller
  5. EASYGATE-RF
  6. Installation manual

golmar EASYGATE-RF Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
easygate
EASYGATE-RF
IM_ENG_REV0123_EASYGATE-RF

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EASYGATE-RF and is the answer not in the manual?

Questions and answers

Summary of Contents for golmar EASYGATE-RF

  • Page 1 EASYGATE-RF IM_ENG_REV0123_EASYGATE-RF...

  • Page 2: Table Of Contents

    10.Annex ..................................10.3.APB 2.INTRODUCTION EASYGATE-RF controller manual. This version of the EASYGATE controller provides the possibility to manage two relays, the first one via proximity and/or RF, the second one via RF. 3.TECHNICAL SPECIFICATIONS Power supply 12 to 24Vdc or 12 a 24Vac Consumption Up to 300mA (in card reading/relay activation).

  • Page 3: Wiring Diagram

    (interference or other radio installations within a close distance). 5.STATUS LEDs MEANING PROG. LED EASYGATE-RF CONTROLLER RED LED FLASHING FAST (3 times per second) Communication problems between reader and controller (check cable connection). RED LED SLOW FLASHING (1 time every 3 seconds) Successful communication between reader and controller.

  • Page 4: Dipswitch

    EASYGATE-RF 6.DIPSWITCH To perform local programming or specific configurations on the controller, it is necessary to manipulate the position of the DIPSWITCHES, the meaning of which is indicated below: Normal use Programming mode Not used Not used APB deactivated APB activated...

  • Page 5: Delete All Master Transmitter Controls

    EASYGATE-RF 7.4.DELETE ALL MASTER TRANSMITTER CONTROLS 1) Remove the power supply to the equipment. 2) Set DIP nº 1 to ON. 1 2 3 4 5 6 3) Connect the equipment to the power supply. *1 beep will be heard.

  • Page 6: Remote Mode Programming (Cloud)

    In case of not being aware of the cloud management environment, please refer to the EASYGATE controller user manual. The following describes the different steps to program an EASYGATE-RF controller in the Cloud (www.easygatecontroller.com) using the two relays. 1) Create a residence, then activate the use of access profiles and set the value 2 in the field “HF”, select the other values (apartments, keys, remote controls,...) according to the needs of the installation.
  • Page 7 EASYGATE-RF 3) Register the controller twice, once to indicate that gate 1 RF will be used and a second time to indicate that gate 2 RF will also be used. 4) Generate access profiles as required, indicating which button on the transmitter control can operate which door.
  • Page 8 EASYGATE-RF 5) Access to apartments (users). 6) Register the transmitters to the apartments (users). www.golmar.es...

  • Page 9: Annex

    EASYGATE-RF 10.ANNEX 10.1.APB (anti-passback up to 500 users) Anti-pass back is a feature which prevents a user from entering into a zone for the second time or to loan his remote to someone else so this second person could enter with the same key. Two consecutive entries w/o exit in between are therefore not possible.
  • Page 10 Sistemas de comunicación S.A. C/ Silici 13. Poligon Industrial Famadas 08940 – Cornellà del llobregat – Spain golmar@golmar.es Tel: 93 480 06 96 www.golmar-seguridad.es Golmar deserves the right for any modification without prior notice.

Table of Contents