Advertisement
Advertisement
Table of Contents
Summary of Contents for OPTOKON KSDT-218
- Page 1 KSDT-218 Dome Optic Splice Closure Installation Guide...
- Page 2 NOTES: 1. Please read the user’s guide before installation. 2. Please pay attention while sealing the cable ports, the inappropriate installation would affect the performance.
-
Page 3: Table Of Contents
List of Contents 1. General Introduction …………………………………………………………….. Page 3 2. Basic structure and configuration ……………….………………………… Page 3 3. Necessary tools for installation ………………..……………………..…….. Page 5 4. Installation flow Chart ……………………………………….….………………..Page 6 5. The process of Splice closure installation …….………………………….Page 7 6. -
Page 4: General Introduction
1. General Introduction KSDT-218 is designed as a multi-functional equipment for optical cable splice, distribution and protection. It can be used for access or branch between optical cables with 5 cable entry/outlet including 1 large round port and 4 small round ports, capable for wide application, excellent sealing performance and easy for installation, and can be deployed for direct buried, wall mount and areal environments. - Page 5 2.2.3 Main accessories Name Buffering tube Nylon cable tie Branching clip Fiber splice protection sleeve Abrasive paper Foil paper Insulation tape Hanging hook(optional) Name Quantity Heat shrink tube (small) Heat shrink tube (large)
-
Page 6: Necessary Tools For Installation
3 Necessary tools for installation 3.1 Supplementary materials (to be provided by operator) Name of materials Usage Scotch tape Labeling, temporarily fixing Ethyl alcohol Cleaning Gauze Cleaning 3.2 Special tools (to be provided by operator) Name of tools Usage Fiber cutter Cutting off fiber cable Fiber stripper Strip off protective coat of fiber cable... -
Page 7: Installation Flow Chart
Installation flow chart Loose the hoop and Open the closure Heat shrink sealing Preparation of optical cable and stripping cable sheath Splice fibers and store rest. Take the stripped fiber into the Fix the splice tray and heat shrink tube and then into enlace them with velcro the base of closure Fix and seal the base and... -
Page 8: The Process Of Splice Closure Installation
5. The process of Splice closure installation 5.1 Preparation of Pre-operation 5.1.1 Check the terminal box type, cable item, and all components before installation 5.1.2 Keep all components dry and clean for installation. 5.1.3 Keep working environment clean (dry and no dust) and flat for installation. 5.1.4 Standard instruments and tools should be used during installing. - Page 9 5.3.3 Unfasten the screws on CSM over the oval ports, inlet uncut cable to inside of closure through oval ports and fix it. 5.3.4 Unfasten the screws on CSM over the round ports, inlet cut cable to inside of closure through round ports and fix it.
- Page 10 5.3.6 Wrap cable with foil paper properly to protect optical cable from heat and use the branching clip in the middle of cable and heat shrink tube. 5.3.7 Proceed the heat shrink process for the cable and heat shrink tube, not let the fire close to the bottom of closure and the cable with foil paper.
- Page 11 5.3.9 Inlet the fibers inside the buffering tube by the oval and round ports to the fiber splice trays. 5.3.10 Assembling the closure after installation of cables, put seal fitting on base, then place the dome cover onto the bottom portion. Fasten the dome cover and the bottom portion together with buckle block . Installation completed.
-
Page 12: Splice Closure Inspecting And Testing Items
6. Fiber Optic Splice Closures (Splice closure) inspecting and testing items Inspecting type Routine test Inspecting item Technical Requirements (Before leaving Type test factory) Each small package contains one fiber optic splice Package closure, together with its accessories, tools, installation manual and packing list. Intact in shape, no burrs, bubbles, chaps, pores, Full Appearance... -
Page 13: Service
Injected air pressure of 60KPa±5 KPa, the temperature circle ranging from -40℃~+65℃, 10 times of the circular tests (one circular consists of high temperature for 2 hours + indoor Temperature temperature for 2 hours + low temperature for 2 circle hours + indoor temperature for 2 hours ) when the pressure declines, the amplitude is ≦5Kpa, immerse the swatch in clean water of normal... - Page 14 OPTOKON, a.s. Other names and trademarks mentioned herein may be the trademarks of their respective owners All rights reserved. No parts of this work may be reproduced in any form or by any means - graphic, electronic, or mechanical, including photocopying, recording, taping or information storage and retrieval systems - without the written permission of the publisher.
Need help?
Do you have a question about the KSDT-218 and is the answer not in the manual?
Questions and answers