Steinigke eurolite LED TRIPLE FX LASER BOX User Manual

3in1 lighting effect with led derby, rg laser and stroboscope

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

Table of Contents

Need help?

Do you have a question about the eurolite LED TRIPLE FX LASER BOX and is the answer not in the manual?

Questions and answers

Summary of Contents for Steinigke eurolite LED TRIPLE FX LASER BOX

Page 2 USER MANUAL LED Triple FX Laser Box DANGER! Electric shock caused by short-circuit Be careful with your operations. With a dangerous voltage you can suffer a dangerous electric shock when touching the wires. Never open the housing. Keep the device away from rain and moisture.
Page 3: Safety Instructions
SAFETY INSTRUCTIONS WARNING! Please read the safety warnings carefully and only use the product as describe in this manual to avoid accidental injury or damage. Intended use • This device is a laser projector for creating decorative lighting effects. This device is designed for professional use in the field of event technology, e.g.
Page 4 Warning – risk of burns and fire • The admissible ambient temperature range (Ta) is -5 to +45°C. Do not operate the device outside of this temperature range. • The housing temperature (Tc) can be up to 50°C during use. Avoid contact by persons and materials. •...
Page 5: Protecting The Environment
Important information for laser products DANGER! Avoid direct eye exposure. Never view directly with optical instruments (e.g. magnifying lens or telescope). Laser radiation can cause eye damage and/or skin damage. All protective measures for a safe operation of this laser must be applied. Safety measures which must be observed •...
Page 6: Description Of The Device
DESCRIPTION OF THE DEVICE RGB LEDs for strobe/wash effects (8) Power on/off Laser output aperture (9) Power feed-through output RGBW LEDs for derby effects (10) Power input Infrared receiver for the remote control (11) Fuse holder Fixation screw (12) DMX output Mounting bracket (13) DMX input Display and operating buttons...
Page 7: Installation
INSTALLATION WARNING! Risk of injury caused by falling objects Devices in overhead installations may cause severe injuries when crashing down. Make sure that the device is installed securely and cannot fall down. The installation must be carried out by a specialist who is familiar with the hazards and the relevant regulations. DANGER! Damage caused by laser radiation Observe the chapter safety instructions when installing the device.
Page 8: Dmx512 Control
CONNECTIONS DMX512 control A DMX512 data link is required in order to control the device via DMX. The device provides 3-pin XLR connectors for DMX connection. Connect the output of your DMX controller to the DMX input DMX IN of the light set with a DMX cable. Connect the DMX output DMX OUT of the light set to the DMX input of the next unit in the chain.
Page 9: Operation
OPERATION Switch on the device. The display indicates the last operating mode. The operating modes can be selected by means of the display and the control buttons. All settings remain stored even if the device is disconnected from the mains. The device can be operated in stand-alone mode via the control board and the EUROLITE IR-26 remote control or in DMX-controlled mode via any commercial DMX controller.
Page 10 Interconnecting several devices (master/slave operation) Several devices may be interconnected (max. 32). Then all slave units can be synchronized and controlled with the master unit without the need for a DMX controller. The devices must be set to the corresponding operating modes.
Page 11: Dmx Operation
DMX operation Setting the number of DMX channels and the DMX starting address For operation with a controller with DMX512 protocol, the device is equipped with 14 control channels. However, it can also be switched to a mode with 2 channels if different functions are required. To be able to operate the device with a DMX controller, the DMX starting address must be set for the first DMX channel.
Page 12 Strobe LEDs 000 – 009 No function 010 – 244 Strobe effects slow > fast 245 – 255 Strobe effects sound controlled 000 – 127 Rotation angle 128 – 255 Rotation speed slow > fast 000 – 009 Strobe effect off 010 –...
Page 13: Cleaning And Maintenance
CLEANING AND MAINTENANCE The outside of the device should be cleaned periodically to remove contaminants such as dust etc. The lenses, in particular, should be clean to ensure that light will be emitted at maximum brightness. Disconnect the device from power and allow it to cool before cleaning. Clean the surface with a soft lint-free and moistened cloth.
Page 15 Eurolite is a brand of Steinigke Showtechnic GmbH Andreas-Bauer-Str. 5 97297 Waldbüttelbrunn Germany D00112264 Version 1.1 Publ. 06/09/2018...

This manual is also suitable for:

51741077