Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Enreach DECT 600 S
- Page 1 Enreach DECT 600 S User Documentation As of: December 2023...
- Page 2 Enreach GmbH assumes no responsibility for printing and writing errors. Despite careful control of the content, Enreach GmbH accepts no liability for the content of external links and does not adopt it as its own. The operators of the linked sites are solely responsible for the content of their sites.
-
Page 3: Table Of Contents
1.6.3.8 Logout ................21 Register handset to Enreach DECT 600 ..........21 Compatibility of SwyxDECT 500 and Enreach DECT 600 S ...... 21 1.8.1 Upgrade for SwyxPhones D510 and D565 ........21 Resetting the base station and handsets to factory settings... -
Page 4: Operating An Enreach Dect 600 System With Swyxware
2 (Dual Cell) Parallel conversations 10 resp. 16 with 2 base stations The DECT 600 L and DECT 600 S base stations cannot be combined with each other. Expandable with number of 6 per base, up to 3 in a chain... -
Page 5: Installation
State signaling by LEDs stand must first be removed. The Enreach DECT 600 S has an LED that signals the states of the system. To mount the Enreach DECT 600 base station on the wall As of v. 5.11, the LEDs also display the RSSI values of the Air Sync func- tion. -
Page 6: Start The Base Station
Start the base station Start the base station Enreach DECT 600 S can be used to operate in a 2-cell system or as a sin- gle cell. The Enreach DECT 600 is preset to use a DHCP server. When first switched on, it automatically obtains an IP address of a DHCP server. -
Page 7: Configuring A Dual Cell System
A Dual Cell system is a coordinated, synchronized system of two base sta- tions to cover a slightly larger radio area. With the Enreach DECT 600 S, only 2 base stations can be set up in a chain. Before installing a Dual Cell system, check the requirements regarding... - Page 8 Operating an Enreach DECT 600 system with SwyxWare Configure base station The start page of the web interface for configuring the Enreach DECT 600 base station opens. Select Management | Country and then select the country and the Save and Reboot.
-
Page 9: Settings At The Webinterface
Operating an Enreach DECT 600 system with SwyxWare Configure base station Configure a second base station by repeating steps and then Function Description steps (20) to (23). Network IP Settings The configured base stations appear after a few minutes in the table... -
Page 10: User
Operating an Enreach DECT 600 system with SwyxWare Configure base station Function Description Global Phonebook Option to load a global telephone book saved on the server. See Central Directory, page 18. Alarm Specify what happens when a user presses the emergency button on their handset. - Page 11 To add a new user can set this himself on his handset if required. To add an extension to the Enreach DECT 600 S, you must first add a handset, see To add a handset, page 11. In the menu bar, select Extensions.
- Page 12 Operating an Enreach DECT 600 system with SwyxWare Configure base station In the field Extension enter the call number and in the field Server Authentication User Name enter the SIP user name that you assigned in SwyxServer within the SIP registration. See also SwyxWare documentation for administrators, Keyword 'SIP Registration' .
- Page 13 DECT 600 S base station. Up to five (for G.711 five, for G.729 five, for to the outside (this option is only useful if the G.722 two) simultaneous calls per repeater are possible.
-
Page 14: Network
Operating an Enreach DECT 600 system with SwyxWare Configure base station IP Settings Avoid registering repeaters and handsets at the same time, as this may Function Description result in undesired cross effects. DHCP/Static IP If the DHCP server is active, the base station obtains the TCP/IP parameters automatically. -
Page 15: Management
Operating an Enreach DECT 600 system with SwyxWare Configure base station 1.6.3.3 Management Firmware Update Country Settings Configuration Syslog/SIP Log... - Page 16 Operating an Enreach DECT 600 system with SwyxWare Configure base station Settings Function Description Syslog level Selection of the different levels of logging. Function Description Base Station Name Enter a name for the base station. Firmware Update Management Transfer The protocol to be used for upload/ In this section you can configure updates of base stations.
- Page 17 Operating an Enreach DECT 600 system with SwyxWare Configure base station Repeater DECT 600: Directory DECT4027("\rtx\DECT600\4027\") Enter the version number of the software to be used to update the handset. All handset types are listed. The 'update over the air' takes some time. All handsets must be in the charging station during the update! Save the handset update data by clicking on Save.
-
Page 18: Security
Operating an Enreach DECT 600 system with SwyxWare Configure base station If you cannot reach a time server in the network, you can take over the 1.6.3.4 Security time from your PC once by clicking on Time PC. However, when the base... -
Page 19: Alarm
Operating an Enreach DECT 600 system with SwyxWare Configure base station To import contacts via a phonebook file from an LDAP server .txt .csv Name and phone number must Name and phone number must Select Central Directory. have the following format:... -
Page 20: Dual Cell
Operating an Enreach DECT 600 system with SwyxWare Configure base station See To add a handset, page 11. Function Description In order to use the alarm function, you must have defined these settings Pre-Alarm Delay Specify an interval in seconds during which an for the user (for each one individually). -
Page 21: Logout
Enreach DECT 600 S timeout. Enreach DECT 600 S is not compatible with DECT 500 systems or Swyx DECT 600 L. 1.6.3.8 Logout By clicking on Logout you log out from the web interface. -
Page 22: Resetting The Base Station And Handsets To Factory Settings
How to reset the Enreach DECT 600 S via the base station Press and hold the reset switch on the base station, see 1.4 General information about the Enreach DECT 600 S , page 5, with a pointed object for at least 10 seconds until the LED lights up solid red.
Need help?
Do you have a question about the DECT 600 S and is the answer not in the manual?
Questions and answers