Do you have a question about the SX-15 and is the answer not in the manual?
Questions and answers
Summary of Contents for Aramsco SX-15
Page 1
Revised: 03/13/2019 LMANAW105 SX-15 HARD SURFACE CLEANING TOOL AW105 Aramsco 4282 South 590 West Salt Lake City, UT 84123 801-268-2673 801-268-3856 FAX...
Page 2
Congratulations on your purchase of the SX-15 hard surface cleaning tool. Years of experience, engineering, and planning have gone into the design and manufacturing of the SX-15. We take a great deal of pride in the SX-15; our goal is no less than your complete satisfaction.
After each use rinse the Inner Shell of the SX-15 to remove accumulated dirt & debris. The Inner Shell can be separated from the Outer Shell to clean the air flow channel between the two shells.
Page 4
To prevent the SX-15 from sticking to the floor and to make the SX-15 easier to move, push the vacuum relief slide to the right to open the vents. Try different slide position settings to get the best movement and recovery for your equipment and the type of floor being cleaned.
Page 5
Solution Hose swivel. Lift the three retainer levers on top of the SX-15 head to release the retainers. Three Retainer Levers Turn the deck over and turn the three rectangular retaining nuts on the retainers to align with the holes in the bottom of the Inner Shell, so they can pass through the holes.
Page 6
Open retaining levers and tighten retaining nuts as needed to assure that the inner shell is properly secured when the latches are pushed down. Reconnect the solution hose to the swivel, and the SX-15 is reassembled.
Page 7
The recommended range of pressure for SX-15 operation is 700 to 1500psi. Set-up Procedure Connect the vacuum hose from your extractor to the vacuum pipe on the SX-15 handle. 2” vacuum hose and cuff is recommended. This will fit over the pipe. 1- 1/2”...
Page 8
The Gekko tool with the Edge & Corner attachment works great for cleaning the tile coving and edges. For heavier soiling not removed by the SX-15, use the Gekko tool with a five inch head straight on, blasting the soil off of the grout.
SX-15 Parts SPRAY GUN SPRAY GUN 100010 100010 SPRAY GUN - BODY ONLY DECAL SX-15 HANDLE NA031B NM5602 DECAL SX-15 HANDLE NM5602 HANDLE SX-15 SS NM5774 SPRAY GUN - BODY ONLY NA031B HANDLE SX-15 SS NM5774 VACUUM HOSE 2” ID NM5726 ( 30”)
Page 10
SX-15 Parts SWIVEL W/ FLANGE HANDLE SX-15 SS DECAL SX-15 HEAD NX105 NM5774 NM5600 OUTER SHELL- TOP VIEW NM5763 SWELL LATCH (QTY 3) SOLUTION HOSE HP 3/16” ID X 50” NM5768 1/8” MPT & ¼” MPT ENDS NM4088 BRUSH RING...
Page 11
BUSHING BRONZE 3/8” ID X 5/8” OD X 2” NM5770 (QTY 2) SX-15 Parts HANDLE SX-15 SS NM5774 NUT 3/8-16 SS NYLOCK NM4085 (QTY 2) SCREW 3/8-16 X2” SS SOC HEAD NM5780 (QTY 2) WASHER FLAT 3/8” SS PA189 (QTY 2)
Page 13
SX-15 Parts VEEJET 1/8” SS MEG0502 (QTY 2) VACUUM RELIEF RING B632 NM5765 SPRAY BAR SS SWIVEL W/ FLANGE NX115 NX105 INNER SHELL TOP VIEW INNER SHELL BOTTOM VIEW NM5761 NM5761 SCREW 1/4-28 X ½” SS PHP SPRAY BAR SS...
Page 14
1/8 MPT & 1/4 MPT ENDS NM4088 NM5778 NM5776 SPRAY GUN - BODY ONLY SPRAY GUN NA031B 100010 NUT 10-32 NYLOCK SPRAY GUN - BODY ONLY NM4028 (QTY 6) NA031B SPRAY GUN 100010 DECAL SX-15 HANDLE NM5602 SCREW 10-32 X 1-5/8 BHSOCSS NM4080 (QTY 6)
Page 15
SX-15 Parts ELBOW 45 1/4Ò STREET BR272 SPRAY GUN 100010 STRAINER BODY NA0802 QC 1/4Male AH102B REPLACEMENT VALVE FOR 100010 SPRAY GUN STRAINER ADAPTER ELBOW 90 1/4 STREET NA033 NA0804 BR282 VALVE REPAIR KIT FOR 100010 SPRAY GUN NA033A QC 1/4Male...
LIMITED WARRANTY Your SX-15 tile cleaning tool is designed to give you years of reliable service. If a problem should arise contact your distributor or Hydro Force for assistance. Hydro-Force warrants the SX-15 tile cleaning tool to be free from defects in material or...
Need help?
Do you have a question about the SX-15 and is the answer not in the manual?
Questions and answers