Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Dynapac REDLINE RF2
- Page 1 INSTRUCTION MANUAL FREQUENCY Converters RF2 & RF4 FREQUENCY Converters...
- Page 2 Paver Finisher FREQUENCY Converters Vibratory Plate Compactor FREQUENCY Converters...
-
Page 3: Table Of Contents
Table of Contents Table of Contents Foreword ................1 Introduction................. 2 Safety Notes................02 Warning and Safety Instructions ............02 Technical Data ................04 General Characteristics..............05 Safety at work ................05 Conditions of Use................05 Instructions of Use.................06 Maintenance Instructions.. - Page 4 Table of Contents FREQUENCY Converters...
-
Page 5: Foreword
Operation Manual - Foreword Foreword These operating and maintenance instructions are part of your machine. They provide necessary information to operate your machine safely and properly. They also contain information on required operating, maintenance and repair measures. Carefully read the operating and maintenance instructions before taking your machine into operation. -
Page 6: Introduction
Operation Manual - Safety Instruction Safety Notes This manual contains CAUTIONS and WARNINGS which must be followed to prevent the possibility of improper service, damaged to the equipment, or personal injury. Read and follow all the CAUTIONS and WARNINGS included in this instructions manual. WARNING: Warnings warn of conditions or practices which could lead to personal injury. - Page 7 Make sure any supporting this instruction manual, should be structures are strong enough and stable performed by an authorized REDLINE enough to support your weight and the Dynapac Service Representative. weight of any equipment on it. Save these instructions! FREQUENCY Converters...
-
Page 8: Technical Data
Operation Manual - Technical Specifications Technical Data Output Weight Input Tension Output Tension Type Fuel Voltage Outlets and Frequency and Frequency (lbs.) 220 V. 50 Hz. RF-2 ------ 42 V. 200 Hz. Single-Phase (37) 380/400 V. 50 RF-4 ------ 42 V. 200 Hz. Hz. -
Page 9: General Characteristics
The manufacturer or authorised distributor must be consulted about any doubts. The manufacturer REDLINE Dynapac., will not accept any responsibility derived from incorrect installation, manipulation, or misuse of the vibrator. Safety at work FREQUENCY Converters - model, fulfils the E.C. -
Page 10: Instructions Of Use
Operation Manual -SAFETY INSTRUCTION-QUICK GUIDE Instructions of Use Put the Converter the most move away possible of the zone to vibrate, to avoid possible projections of concrete, in the event of taking place they must be wiped with a wet cloth before that they are dry. - Page 11 Operation Manual -SAFETY INSTRUCTION-QUICK GUIDE Under ANY circumstances made any kind of operation or part substitution with the machine switch plugged in the network. DO NOT allow personnel not capable to make use of the vibrator or manipulate the electric parts.
-
Page 12: Maintenance Instructions
When spare parts are required for petrol engine or Diesel engine furthermore give the make, model and Serial number of the engine. When equipment or spare parts have to be returned to the factory its necessary to contact with REDLINE Dynapac for prior agreement, “AN ABSOLUTE NECESSITY FOR THEIR RECEPTION”. FREQUENCY Converters... -
Page 13: Transport And Storage
During the period of guarantee the breakdowns must be repaired by personnel from REDLINE Dynapac., authorised to do so, if this is not so the right given by the guarantee will be lost. The equipment which has been dismantled or manipulated previously by personnel unauthorised by REDLINE Dynapac will not be in guarantee. -
Page 14: Troubleshooting
Operation Manual - Important Advice 2.12 Troubleshooting SYMPTOM PROBABLE CAUSE COUNTERMEASURE -Fail of the line phase. -Checking and convert. The converter doesn’t -Electrical connections are let or broken. -Checking and replace. work. -Faulty switch. -Replace. -Checking line, cable and plugs. The converter doesn’t -Fail of the line phase. -
Page 15: Do's &Don'ts
Operation Manual - Important Advice 2.13 Do’s &Don’ts RF Converters 1) To ensure the proper func�oning of the converter, ensure that operators have received proper training in its management. 2) The converter should only be used for specific tasks as outlined in this manual. 3) Prior to connec�ng the converter to the electrical system, confirm that the voltage and frequency match the specifica�ons listed on the equipment plate located on the top part.
Need help?
Do you have a question about the REDLINE RF2 and is the answer not in the manual?
Questions and answers