Hotpoint NTM119X3EUK Quick Manual

Quick guide
THANK YOU FOR BUYING A HOTPOINT PRODUCT.
In order to receive a more complete assistance, please
register your product on www.hotpoint.eu/register
CONTROL PANEL
1 ON/OFF Button (hold for Reset)
2 Programme Selection Knob
3 Start/Pause Button
Options Buttons*
4 Active Care
5 Dryness Level
6 Start Delay
7
Timed Drying
8 Cycle End
9 Gentle (hold for Key lock)
10 Crease Care (hold for Mute)
INDICATORS
Dryness Level:
Iron Dry -
Cycle Phase:
Drying -
Empty water tank -
Refer to troubleshooting section:
FIRST TIME USE
Make sure that the water tank is correctly inserted. Make sure
that the drain hose on the back of the dryer is fixed correctly,
either to the dryer's water tank, or to your domestic drainage
system.
The dryer must be installed in a room with a temperature
ranging between 5°C and 35°C to ensure proper operation.
Before using the dryer make sure it has been in an upright
position for at least 6 hours.
Should you wish to change the opening side of the door, please
contact our After-sales Service. (See phone number in the
warranty booklet).
DAILY USE
Doing this will keep your machine working at its BEST:
- remember to empty your water tank after each drying cycle.
- remember to clean your filters after each drying cycle.
Refer to the Care & Maintenance section.
1. Plug the dryer into the power supply socket.
2. Open the door and load garments; always refer to instructions on
clothing labels and the max loads indicated in the programme
section. Empty pockets. Make sure garments do not get caught
between the door and/or the door filter. Do not load items that
are dripping wet. Do not tumble dry large, very bulky items.
3. Close the door.
4. Press the "On/Off" button.
5. Select the most suitable programme for the type of fabric in that
load.
6. Select the options, if necessary.
7. Press the "Start/Pause" button to begin drying.
8. At the end of the drying cycle, a buzzer will beep. An indicator on
the control panel signals the end of the cycle. Pull the load out
immediately to prevent the formation of creases on laundry.
9. Turn the machine off by pressing the "On/Off" button, open the
door and pull the clothing out. If the machine is not switched off
manually, after about a quarter of an hour from the end of the
Policies, standard documentation, ordering of spare parts and additional product information can be
cycle , the appliance turns off automatically to save energy.
found by:
Note that some programme/option accords with "Crease Care"
• Visiting our website docs.hotpoint.eu and parts-selfservice.whirlpool.com
system. This means that for some hours, after the end of the
• Using QR Code
drying cycle, the drum rotates at regular intervals to prevent the
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet). When
formation of creases.
contacting our After-sales Service, please state the codes provided on your product's identifi cation plate.
In case of power failure, it is necessary to press the "Start/Pause"
button to restart the cycle.
2
Hanger Dry -
Cool Down - END End of Cycle
Clean door filter - Clean bottom filter
Failure: Call after sales service -
Before using the appliance carefully read the Safety
Instructions.
Lorem ipsum
D D E E M M O O
*Note: some models may have the wording in full instead of the icons.
Cupboard Dry - Extra Dry
Demo Mode
DEMO
OPENING THE DOOR DURING THE CYCLE
Laundry can be checked while the drying cycle runs and any
garments already dry can be removed, while drying continues for
the remaining items. After closing the door, press the "Start/Pause"
button to resume machine operation.
Keep the door closed until the cycle end to save time and energy.
CARE LABEL
Always check the care labels, especially when placing garments in
the tumble dryer for the fi rst time. Below are the most commonly
used symbols:
May be tumble dried.
Do not tumble dry.
Tumble dry – high heat.
Tumble dry – low heat.
END END
h
h h
5 6 7
EN
1
10
3
" "
4
9
3
" "
3
8
xxxx
xxxxxxxxxxxx