Oldfields AL-FSHA-M Instructions

MINI ZIPPY-SCAFF
BASE UNIT
INSTRUCTIONS
MINI Base Unit Scaffolding Pack Components
Item Code: AL-FSHA-M ITEM CODE
AL-FSDHA-M-CD
AL-FSASC-M-CD
MINI
MINI BASE UNIT SCAFFOLDING PACK COMPONENTS
ITEM CODE
MINI
Item Code
General AL-FSDHA-M-CD
ITEM CODE
AL-FSASC-M-CD
AL-FSDHA-M-CD
These assembly instructions apply to assemble of the base unit configuration of the
AL-FSDHA-M-CD
AL-FSASC-M-CD
Oldfields Zippy-Scaff Mini folding scaffold, where the deck height ranges from 0.4m
General
AL-FSASC-M-CD
to 1.1m above ground level.
These assembly instructions apply to assemble of the base unit configuration of the
General
Oldfields Zippy-Scaff Mini folding scaffold, where the deck height ranges from 0.4m
Step 1:
GENERAL These assembly instructions apply to assemble of the base unit configuration of the
Stand up frame assembly on hard, flat, level surface.
to 1.1m above ground level.
Oldfields Zippy-Scaff Mini folding scaffold, where the deck height ranges from 0.4m
These assembly instructions apply to the assembly of the Oldfields Mini
to 1.1m above ground level.
Step 2:
Step 1: Pull each of the frames away from each other extending and opening up the
Zippy-Scaff folding scaffold base unit, where the deck height ranges from
Stand up frame assembly on hard, flat, level surface.
assembly. (See Fig.1)
0.4m to 0.8m above ground level. Step 1:
Stand up frame assembly on hard, flat, level surface.
Step 2:
Pull each of the frames away from each other extending and opening up the
Step 1: Stand up frame assembly on hard, flat, level surface.
Note: If Zippy-Scaff Mini "sticks" whilst opening or closing frames, DO NOT FORCE, give
Step 2: assembly. (See Fig.1)
Pull each of the frames away from each other extending and opening up the
Step 2: Pull each side of the frames away from each other extending
the unit a gentle shake to free braces. For maximum stability ensure the castors are
assembly. (See Fig.1)
and opening the pivot arm assembly. (See Fig.1)
Note: If Zippy-Scaff Mini "sticks" whilst opening or closing frames, DO NOT FORCE, give
positioned with brake levers facing outwards at right angles to the deck.
Note: If Mini Zippy-Scaff "sticks" while opening or closing frame, DO NOT
the unit a gentle shake to free braces. For maximum stability ensure the castors are
Note: If Zippy-Scaff Mini "sticks" whilst opening or closing frames, DO NOT FORCE, give
FORCE, give the unit a gentle shake to free the pivot arms. For maximum
positioned with brake levers facing outwards at right angles to the deck.
Step 3 the unit a gentle shake to free braces. For maximum stability ensure the castors are
: Push upwards at pivot arm hinges until pivot arms are straight and hinge locking
stability ensure the castors are positioned with brake levers facing inwards
positioned with brake levers facing outwards at right angles to the deck.
mechanisms on each pivot are engaged (see Fig.2)
Step 3
at right angles to the deck.
: Push upwards at pivot arm hinges until pivot arms are straight and hinge locking
Step 3 mechanisms on each pivot are engaged (see Fig.2)
Step 3: Push upwards on pivot arm hinges until both arms are straight
: Push upwards at pivot arm hinges until pivot arms are straight and hinge locking
Step 4
: Fit deck onto to the required rung level ensuring that deck hooks are supported
and hinge locking mechanisms on each arm is engaged. (see Fig.2) mechanisms on each pivot are engaged (see Fig.2)
by the rungs at the same level. Insert deck on angle "diagonally" between frame uprights
Step 4
: Fit deck onto to the required rung level ensuring that deck hooks are supported
Step 4: Fit deck onto the required working level ensuring that deck hooks
and rungs until hooks clear upright at other end, then slide deck back to fit hooks onto
Step 4 by the rungs at the same level. Insert deck on angle "diagonally" between frame uprights
: Fit deck onto to the required rung level ensuring that deck hooks are supported
are supported by frame rungs at the same level. Insert deck on angle
rungs. Push deck firmly down to locate hooks (it is intended to be a tight fit).
and rungs until hooks clear upright at other end, then slide deck back to fit hooks onto
by the rungs at the same level. Insert deck on angle "diagonally" between frame uprights
"diagonally" between frame uprights and rungs until one side has cleared
rungs. Push deck firmly down to locate hooks (it is intended to be a tight fit).
and rungs until hooks clear upright at other end, then slide deck back to fit hooks onto
the upright and rung, then slide deck back to fit into place with all four
Deck is positioned at typically at 2
rungs. Push deck firmly down to locate hooks (it is intended to be a tight fit).
hooks locking onto frame rungs.
Deck is positioned at typically at 2
above ground level. Deck may also be fitted to lower rung levels as required. (See Fig. 3)
above ground level. Deck may also be fitted to lower rung levels as required. (See Fig. 3)
Deck is positioned typically at 1st or 2nd rung height, giving a deck working
Deck is positioned at typically at 2
height of typically 0.4m and 0.8m above ground level. (See Fig. 3)
above ground level. Deck may also be fitted to lower rung levels as required. (See Fig. 3)
The deck MUST NOT be placed on the top rung, unless guard rail
The deck MUST NOT be placed on the top rung, unless guard rail
pack is fitted. See Zippy-Scaff Mini Guard Rail Pack Folding Scaffold assembly Note: The deck MUST NOT be placed on the 3rd or top rung unless guard
pack is fitted. See Zippy-Scaff Mini Guard Rail Pack Folding Scaffold assembly
The deck MUST NOT be placed on the top rung, unless guard rail
instructions.
rail extension pack is fitted.
instructions.
pack is fitted. See Zippy-Scaff Mini Guard Rail Pack Folding Scaffold assembly
See Mini Zippy-Scaff 1.5m Guard Rail Extension Pack assembly instructions.
instructions.
Step 5
: Roll scaffold to desired location.
Step 5
Step 5: Roll scaffold to desired location. : Roll scaffold to desired location.
Step 5
: Roll scaffold to desired location.
Step 6: Apply brakes to all castors (lock).
Step 6
Step 6
: Apply brakes to all castors (lock). The Zippy-Scaff Mini Folding Scaffold is
: Apply brakes to all castors (lock). The Zippy-Scaff Mini Folding Scaffold is
The Oldfields Mini Zippy-Scaff Folding Scaffold is now ready for use.
now ready for use. (See Fig. 3) Step 6 now ready for use. (See Fig. 3)
: Apply brakes to all castors (lock). The Zippy-Scaff Mini Folding Scaffold is
(See Fig. 3)
now ready for use. (See Fig. 3)
Note: Deck Maximum Working Load is 225kg
Note
Note : Deck Maximum Working Load is 225kg
: Deck Maximum Working Load is 225kg
Note: To increase the deck height from 1.2m to 1.5m from ground level
Note:
Note
To increase the deck heights you will need to purchase a Zippy-Scaff Mini
: Deck Maximum Working Load is 225kg
Note:
To increase the deck heights you will need to purchase a Zippy-Scaff Mini
you will need to purchase a Oldfields Mini Zippy-Scaff 1.5m Guard Rail
Note: Guard Rail Pack.
To increase the deck heights you will need to purchase a Zippy-Scaff Mini
Guard Rail Pack.
Extension Pack. ITEM CODE DESCRIPTION QTY: AL-FSDHA-M-CD Folding
Guard Rail Pack.
Scaffold Assembly 1pc, AL-FSASC-M-CD Hatch Deck assembly 1pc.
www.oldfields.com.au
DESCRIPTION
Folding Scaffold Assembly
Hatch Deck assembly
Base Unit Scaffolding Pack Components
DESCRIPTION
Base Unit Scaffolding Pack Components
Description
Folding Scaffold Assembly
DESCRIPTION
Hatch Deck assembly
Folding Scaffold Assembly
Folding Scaffold Assembly
Hatch Deck assembly
Hatch Deck assembly
rung height, giving deck working heights of 0.7m
nd
nd rung height, giving deck working heights of 0.7m
nd rung height, giving deck working heights of 0.7m
QTY Product Description: Base Unit 1.1m
1
1
QTY
1
QTY
1
1
1
THE PROFESSIONALS CHOICE SINCE 1916
QTY
1
1
Ph: 13 62 60