Related Manuals for Venue revolver wash
Summary of Contents for Venue revolver wash
- Page 1 DUAL-SIDED MOVING HEAD EFFECT LIGHT WITH WASH AND MOONFLOWER www.venuelightingeffects.com...
-
Page 3: Table Of Contents
INTRODUCTION The Venue Revolver Wash is a DMX intelligent, dual sided, moving head effect light, which includes both a wash and moonflower effect. It is lightweight and compact which makes it a great light for mobile DJs, clubs and parties. This unit can be used as a standalone fixture in sound-activated mode, or controlled via DMX controller. -
Page 4: Before You Begin
This paragraph contains important installation or configuration information. Failure to comply with this information may prevent the fixture from functioning correctly. This paragraph reminds you of useful, although not critical, information. Venue Revolver Wash Manual... -
Page 5: Safety Instructions
SAFETY INSTRUCTIONS Please read these instructions carefully. It includes important information about the installation, usage and maintenance of this product. FCC Statement 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. -
Page 6: Introductions
• Built-in automated programs via master/slave or DMX with variable speed • Built-in sound activated programs via master/slave or DMX • 10, 12, and 20 channel DMX-512 operation Additional Features • Includes rubber feet for desktop placement & metal bracket/safety loop for truss mounting Control Panel Venue Revolver Wash Manual... -
Page 7: Setup
SETUP AC Power This fixture runs on 100~240 VAC, 50/60 Hz. Before powering on the unit, make sure the line voltage is within the range of accepted voltages. To determine the power requirements for a particular fixture, see the label affixed to the bottom of the fix- ture or refer to the fixture’s specifications chart. -
Page 8: Mounting Orientation
Mounting Orientation The Revolver Wash includes a metal bracket and safety loop for hanging upside-down only. Mounting Orientation Be sure that the structure can support the weight of the fixture. Please see the “Technical Specifications” section of this manual for a detailed weight listing. Mount the fixture securely. This may be done with a screw, nut and bolt, or a hanging clamp (not included). -
Page 9: Signal Linking
Signal Linking In order to use this fixture in a DMX or master/slave operation, you must daisy chain using DMX cables to link from one fixture to another. OPERATING INSTRUCTIONS Control Panel Buttons Access these functions using the four buttons located directly underneath the LED Control Display. BUTTON FUNCTION Scrolls through the current operating mode, as well as back out... -
Page 10: Menu Map
Auto Mode must be turned “OFF” for Sound Active mode Select sensitivity level of the Audio Sens 0–100 microphone between 0 (less sensitive) Sensitivity and 100 (more sensitive). Pause current program (Blackout) Pause Mode bLNd Resume program Venue Revolver Wash Manual... - Page 11 Control Panel Menu Selections (Continued) SUB- MAIN FUNCTION SELECTION INSTRUCTION FUNCTION Stda Select “Standard” dimming mode StGE Select “Stage” dimming mode Dimming dINd Select “TV” dimming mode ArAL Select “Architectural” dimming mode tHAL Select “Theatrical” dimming mode Select standard or reverse Pan Turn PInt X-axis movement...
-
Page 12: Standalone Operation
4. Press <ENTER>. 5. Press <MENU> until “Auto” appears on the LED screen. 6. Using <UP> and <DOWN>, select “on” to enable quick movement sequences, or “oFF” to enable a slow pan. 7. Press <ENTER> to confirm settings. Venue Revolver Wash Manual... -
Page 13: Sound-Active
Sound-Active While an automatic program is enabled, you can choose whether or not to use the built-in microphone for sound-active response. This option is accessed via the Control Display (page 6). 1. Press <MENU> until “SoUn” appears on the LED screen. 2. -
Page 14: Dmx Operation
Only one fixture may be set to master. Do not connect a DMX controller to the daisy chain for this operating mode. It does not matter which DMX mode is selected for the slave fixtures. Either mode will be effective. Venue Revolver Wash Manual... -
Page 15: 10-Ch Mode Dmx Operation
10-Ch Mode DMX Operation 20-Ch Mode DMX Operation CHANNEL CHANNEL FUNCTION CHANNEL CHANNEL FUNCTION Pan Turn Pan Turn Tilt Turn Tilt Turn Tilt Unlimited Rotation Tilt Unlimited Rotation Red1 Red2 Pan/Tilt Speed Green1 Green2 Red1 Blue1 Blue2 Green1 White1 White2 Blue1 Strobe White1... -
Page 16: Dmx Parameters
20-Ch Mode DMX Operation MODE MODE MODE FUNCTION VALUE PERCENT/SETTING 10 CH 12 CH 20 CH 000–255 0~100% Tilt 000–255 0~100% 000–127 Null 128–189 Counter-clockwise from fast to slow Tilt Unlimited Rotation 190–193 Stop 194–255 Clockwise direction from slow to fast Pan/Tilt Speed 000–255 From fast to slow... - Page 17 20-Ch Mode DMX Operation (Continued) MODE MODE MODE FUNCTION VALUE PERCENT/SETTING 10 CH 12 CH 20 CH 068–071 Color 17 072–075 Color 18 076–078 Color 19 079–082 Color 20 083–086 Color 21 087–089 Color 22 090–093 Color 23 094–097 Color 24 098–101 Color 25 102–104...
-
Page 18: Appendix
20-Ch Mode DMX Operation (Continued) MODE MODE MODE FUNCTION VALUE PERCENT/SETTING 10 CH 12 CH 20 CH Pan/Tilt Speed 000–255 From slow to fast 000-069 070-079 Pause light on pan/tilt turn 080-089 090-099 Pause light on color change 100-179 Multi-Working Mode 180-189 Auto Mode 190-199... -
Page 19: Fixture Linking
Fixture Linking You will need a serial data link to run light shows of one or more fixtures using a DMX controller or to run synchronized shows on two or more fixtures set to a master/slave operating mode. The combined number of channels required by all the fixtures on a serial data link determines the number of fixtures the data link can support. -
Page 20: 3-Pin To 5-Pin Conversion Chart
Clean with soft cloth using normal glass cleaning fluid. Clean the external optics at least every 20 days. Clean the fixture at least every 30/60 days. Venue Revolver Wash Manual... -
Page 21: Technical Specifications
Always dry parts carefully after cleaning them. Never spin a fan using compressed air. TECHNICAL SPECIFICATIONS Weight & Dimensions Length: 6.86” (174.3mm) Width: 5.78” (147mm) Height: 8.98” (228.1mm) Weight: 5.64 lbs (2.56 kg) Power Auto-Ranging Power Supply: 100~240 VAC, 50/60 Hz Power Consumption @ 120 V: 58 W max, 0.78 A inrush Power Consumption @ 230 V:... -
Page 22: Warranty
Venue® products. This guarantee gives you specific legal rights. You may have other legal rights which vary from state to state. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. - Page 24 www.venuelightingeffects.com 1907-19356055...
Need help?
Do you have a question about the revolver wash and is the answer not in the manual?
Questions and answers