Summary of Contents for Salamander Pumps AquaScan
- Page 1 User Guide This document should be retained for future reference. Should you need to contact Salamander Pumps you will need the below information: ISSUE 1.0 AUGUST 2024...
-
Page 2: Table Of Contents
Kitchen tap - aerator connection Terms and conditions g) Kitchen tap - mixer connection h) Single tap connection i) Shower hose connection j) Shower arm connection k) Washing machine connection l) AquaScan isolation valve removed m) AquaScan isolation valve connected to hose AquaScan Guide... -
Page 3: Safety And Contact Information
• At the end of its useful life, please dispose of the product at the collection • AquaScan provides an indication of water pressure, temperature, flow and point for electric and electronic devices (observe local regulations). total dissolved solids (TDS)/hardness. -
Page 4: Intended Use
Intended use AquaScan carrycase AquaScan is a digital water multimeter, it will measure water pressure, flow, temperature, and will give an indication of water hardness via Total Dissolved Solids (TDS). It may only be used under the conditions and for the purpose for which it was designed. - Page 5 ½”connector x1 ½” washers x2 Use this notepad to record AquaScan results and ensure you have the information necessary to specify products to improve water pressure and/or flow in a property Customer Details: MainsBooster Outlet 1...
-
Page 6: Product Overview
AquaScan is supplied in a robust storage case with a range of accessories for easy connection to common outlet types. The unit is powered by an integral battery, rechargeable via a USB-C input. -
Page 7: D) Aquascan Display
AquaScan display Display 3 - QR code Display 1 - animated Battery level indicator Battery level indicator Flow For help interpreting your Flow rate Flow Temp results and product support reading Temperature scan the QR code reading Peak Peak... -
Page 8: Operation
Peak Peak Peak 20 Peak 21 Pressure Peak 20 Always use the USB-C to USB cable supplied with AquaScan. Peak reading 2. Plug the USB-C into USB-C port on AquaScan. Pressure Pressure Peak 2.5 Display 2 - simple - TDS reading and hardness indication... - Page 9 4. When AquaScan is turned on, the battery level indicator will change to ‘charging’: When AquaScan is turned off and charging the display below will be shown. Display 1 - animated Display 2 - simple Display 3 - QR code...
-
Page 10: C) Turning On / Turning Off
- AquaScan will power up with the last used display. display 1 - animated display 2 - simple display 3 - QR code - AquaScan will automatically power off after 20 minutes to save battery power. d) Reset peak values: The peak values are shown for each reading. Flow... -
Page 11: E) Change Display
Peak 6 Pressure Pressure Pressure Pressure Peak 1.5 Peak 1.5 Temperature Temperature Peak Peak °C °C Peak 12 Peak 12 2. Press display button to change display Please note AquaScan will power up with the last used display. AquaScan Guide... -
Page 12: Common Connection Examples
Common connection examples c) Garden tap - hose adaptor connection with flexible hose The hose supplied with AquaScan can be used to direct water to a convenient waste point. Do not allow the hose to bend/kink as this will restrict the flow and prevent an accurate reading. AquaScan comes with a variety of connection accessories to allow the unit to be connected to various outlets. -
Page 13: E) 22Mm Pipe Connection
¾” washer h) Single tap connection f) Kitchen tap - aerator connection Single tap to male hose connector Remove the aerator from the tap first, before connecting AquaScan. ¾” male thread to hose quick connector ¾” washer ¾” washer Male and female ¾”... -
Page 14: I) Shower Hose Connection
AquaScan isolation valve connected to hose The supplied isolating valve can be connected to the flexible hose to allow AquaScan to fit into tight spaces. Do not allow the hose to bend/kink as this will restrict the flow and prevent an accurate reading. This method should not be followed when measuring the water flow rate when specifying a gravity fed pump. -
Page 15: Carrying Out A Measurement
W/ / C BATHROOM Peak 6 AquaScan can measure up to 30L/min. If the flow rate at one outlet exceeds 30L/min or if you believe the AquaScan is restricting the flow follow the steps to measure the total incoming flow. -
Page 16: C) Measuring Pressure (Bar)
Measure static pressure at an outlet on the ground floor (or on the same temperature of hot water to prevent serious injury. 1) Connect AquaScan to the outlet (guidance on this is outlined in section level as the where the mains enters the property). Ensure all outlets in the Common connection examples). - Page 17 HARDNESS 300+ MODERATELY SLIGHTLY SOFT HARD VERY HARD HARD HARD Source: Drinking Water Inspectorate “Hardness of Water”. Available from: https://www.dwi.gov. uk/consumers/learn-more-about-your-water/water-hardness-hard-water/ To control temperature a TMV can be installed Find out more: www.salamanderpumps.co.uk AquaScan Guide...
-
Page 18: Improving Water Performance After Measurements Have Been Taken
AccuBoost 120 without the flow dropping off. The vertical red line on the graph indicates 20l/min. Salamander Pumps’ AccuBoost 60 TankBoost, AccuBoost 450L or AccuBoost 330L will deliver more than 20L/ min, with TankBoost delivering up to 80L/min. -
Page 19: B) Increasing Pressure In Mains-Fed Systems
The red line on the graph shows at 20L/min flow rate, Salamander Pumps’ TankBoost will deliver 2.7 Bar pressure. Therefore by installing TankBoost the pressure is strong enough to boost the water to the outlets on the top floor.. -
Page 20: C) Increasing Pressure In Gravity-Fed Systems
2.0 Bar Pumps enough for powerful showers or flowing taps. The pumps in Salamander Pumps’ range will improve the pressure in these systems, whether you need to boost water pressure for a single shower or tap, multiple outlets in the bathroom, or throughout the entire house. -
Page 21: Treating Hard Water
Treating hard water 3.0 Bar Pumps Hard water (high limescale content) can be treated with products such as Salamander Pumps’ range of water conditioners. a) Which water conditioner do I need? Whole house Single outlet (ie. shower) Flow rate (L/min) -
Page 22: Service And Maintenance
Technical Specification Part Number AQUASCAN a) Maintenance Warranty 1 year When operated in accordance with the user guide, AquaScan does not Height (mm) require any particular maintenance. In the unlikely event a malfunction AquaScan with Width (mm) isolation valve occurs, contact Salamander Pumps. -
Page 23: Troubleshooting
Please see table below for troubleshooting guidance should you experience Battery not Fault with power Check both ends of the USB an issue with AquaScan. If this does not provide a solution, then please charging cable charging cable for any visible contact our Customer Service Team for support. - Page 24 Identified Probable cause Recommended solution problem problem Battery not AquaScan has If AquaScan feels hot or warm allow Screen is TDS (hardness Open and close the isolation valve charging turning on, but overheated it to cool, moving it into a cooler...
-
Page 25: Warranty
To get the most from your Salamander Pumps product, please follow the user higher or lower is trapped in AquaScan. Ensure the guide provided, ensure it is stored in the protective case supplied, and only... -
Page 26: Terms And Conditions
This Warranty shall only be enforceable by you if the following terms and conditions have been complied with: AquaScan Terms and Conditions (UK, Northern Ireland & ROI Republic of Ireland) a. That the product has been used in accordance with the user guide. - Page 27 This Warranty is valid and enforceable for equipment purchased and used exclusively in the UK and The Republic of Ireland only. g. No authority has been given to any person, firm, or company to vary the terms of this Warranty. h. Warranty does cover accessories supplied. AquaScan Guide...
- Page 28 AquaScan Guide...
- Page 29 Get in touch, we’re here to help call us on 0191 516 2002 Unit 2c Colima Avenue Enterprise Park West Sunderland, SR5 3XE Register your product Online: www.salamanderpumps.co.uk By phone: 0191 516 2002...
Need help?
Do you have a question about the AquaScan and is the answer not in the manual?
Questions and answers