Subscribe to Our Youtube Channel
Summary of Contents for Gunnebo Hamilton Air HA-45
- Page 1 3143 Production DriveFairfield, Ohio 45014513-874-3733 HA-45 HA50 Model with I/O controls. Removable or remote turbine packs. Installation and Service Manual...
-
Page 2: Important Notice
Important Notice: This Unit requires CAT5 interconnection Models that include the I/O control boards (E0873) are interconnected from customer to teller unit with a single CAT5 cable (Hamilton P/N E0889). This replaces the multi- conductor cable used on previous versions. Audio connections remain similar to previous models requiring a separate multi-conductor cable (P/N E0680) connected between the customer unit and audio matrix. - Page 3 HA45 / HA50 Turbine Power Wire Connection The unit is shipped with the RED main turbine power wire connected to terminal #4 ready for turbine pack to be mounted inside customer unit. If the system will use the remotely mounted turbine pack, the RED main turbine power wire must be moved to terminal #5.
- Page 4 BRAKE TUBE SLEEVE (PART # B4408) SOFT LANDING TOP FITTING (PART # B4406) 4 3/4 ACRYLIC ADAPTER SLEEVE (PART # B4050) STEEL TO PVC ADAPTER (PART # T9705) TELLER UNIT HA45 TURBINE PACKAGE (PART # 99-914) (PART # B10014) ACRYLIC EXHAUST TUBE PACKED INSIDE 4-1/2"...
- Page 5 BRAKE TUBE SLEEVE STEEL TO PVC ADAPTER (PART # B4408) (PART # T9705) HA50 TURBINE UNIT (PART # 99-954) ACRYLIC TO PVC ADAPTER (PART # T9704) CEILING TRIM RING (PART # T9713) 4 3/4 ACRYLIC ADAPTER SLEEVE AIRFLOW CONTROL VALVE (PART # B4050) (PART # B5471) 3"...
-
Page 6: Switch Settings
Switch Settings The switches on the control boards are used to set functions and test operations. There are three slide switches and one pushbutton switch located on the control boards. The three slide switches are labeled #1, #2, and #3 while the fourth pushbutton switch (SW4) is labeled “Carrier Recall”. -
Page 7: Interconnection Cable
Interconnection Cable CAT5 Interconnect Cable Wiring The I/O control board system requires an interconnect cable to connect the manual teller unit to the control board located in the customer unit and/or the control board located in the teller unit to the control board located in the customer unit. -
Page 8: Microphone Muting
Additional Functions of E0873 Door Auto-Close Option There is a fourth jumper that can be placed across pins #1 and #2 on the J4 input connector that will enable the door auto-close feature. This optional feature when activated by this jumper closes the customer door after three minutes of no activity with the unit. - Page 9 Night Lock Switch on Over Head Teller Night lock operation. The night lock function is used to turn the lane off for the night or whenever the lane will not be used. The night lock function will close the customer unit and call the carrier inside, if needed, to prevent outside use of the lane.
- Page 10 Video Power Control Note, Only used with Hamilton 5517 two-way video units. E10036 Video Power Control Cable Installation Used only for 5517 video units when pneumatic tube system uses E0873-C I/O control boards. 12VDC POWER CABLE VIDEO POWER CONTROL CABLE CONNECTION INSTRUCTIONS USE ONLY FOR 5517 AND 5517-SUN VIDEO UNITS USED WITH PNEUMATIC Inputs 3-12 TUBE SYSTEMS OPERATING WITH HAMILTON'S E0873-C I/O CONTROLS.
- Page 11 Blower Run-Time Set Procedure The “blower run time” is set using switch number one (SW1), which is located on the control board in the customer unit. The unit is shipped with a default time stored of about 3 seconds. This procedure will overwrite any existing times set in system. This time can be reset as often as necessary.
- Page 12 Blower Run Time Set with CM2 Motorized Teller Unit The CM2 teller unit has a pressure switch that will act like a carrier arrival switch turning off the turbine motors. The pressure switch should be activated after the carrier passes the air relief valve in the teller bend turning off the turbines.
- Page 13 Customer Control Board Connections Outputs Opening Closing Pressure Vacuum Power Carrier Recall Spare/Teller Auto Close (Option) Send T/R Call Air Flow Vid. Power Lane Stat Spare Door Safety Night lock Remote Carrier Carrier Present Door Closed Door Open Teller Recall Link Teller Send...
- Page 14 Teller Control Board Connections (Not used with manual teller units) Outputs Opening Closing Pressure Vacuum Power Carrier Recall Spare/Teller Auto Close (Option) Send T/R Call Air Flow Vid. Power Lane Stat Spare Door Safety Night lock Remote Carrier Carrier Present Door Closed Door Open Teller Recall...
- Page 15 Troubleshooting the E0873 Motorized Door Test (Automatic): 1) Disconnect the interconnection cable from the board. 2) If the door is open, turn SW3 “ON”, if door is closed, turn SW3 “OFF”. 3) Cycle power “OFF” and back “ON”. 4) Door should open or close depending on the setting of SW3. 5) Repeat test in both directions and on both tube stations if applicable.
- Page 16 HA45 Turbine Pack Mounting and Connection...
- Page 17 HA50 Remote Mounted Turbine Connections 1 - VACUUM 24VAC 2 - PRESSURE 24VAC 3 - COMMON 24VAC 4 - AIRFLOW (OPTIONAL) 5 - AIRFLOW (OPTIONAL) 6 - NOT USED...
- Page 18 Customer Unit Connections PVC BEND WITH 3" "T" (PART # T9608) PVC BEND (PART # T9603) AIRFLOW CONTROL VALVE (PART # B5471) CEILING TRIM RING (PART # B5353) ACRYLIC TO PVC ADAPTER (PART # T9704) SOFT LANDING TOP FITTING (PART # B4406) CEILING TRIM RING (PART # T9713)
- Page 19 Logic Wiring Detail with Local Turbines Pressure Vacuum SHLD RJ45JACK...
- Page 20 Logic Wiring Detail with Remote Turbines SHLD RJ45JACK...
- Page 21 Air Flow Kits: P/N B10020 for HA45 and B6530 for HA50 Airflow operation: The E0873 control board can be set-up to run an airflow kit for reducing condensation buildup in the tubes. Note: A separate airflow kit must be added to the tube system for this function to operate.
Need help?
Do you have a question about the Hamilton Air HA-45 and is the answer not in the manual?
Questions and answers