Table of Contents
Advertisement
Quick Links
M4Q045-CA01-75
ASIA PACIFIC SHENGRUI LIMITED
Phone +00852 56261528
info@apacshengrui.com
www.apacfan.com
CONTENTS
Item no. 10954-5-9970 · ENU · Change 225340 · Approved 2021-04-28 · Page 1 / 9
Operating instructions
1. SAFETY REGULATIONS AND INFORMATION
Read these operating instructions carefully before starting work on the
device. Observe the following warnings to prevent malfunctions or
danger to persons.
These operating instructions are to be regarded as part of the device.
The device is only to be sold or passed on together with the operating
instructions.
These operating instructions may be duplicated and distributed to inform
about potential dangers and their prevention.
1
1.1 Hazard levels for warnings
1
1
These operating instructions use the following hazard levels to indicate
1
potentially hazardous situations and important safety regulations:
1
2
2
2
2
2
3
4
4
5
5
5
5
6
6
6
1.2 Staff qualifications
6
The device may only be transported, unpacked, installed, operated,
7
maintained and otherwise used by suitably qualified, trained and
8
authorized technical staff.
8
Only authorized specialists are permitted to install the device, to carry
8
out a test run and to perform work on the electrical installation.
8
1.3 Basic safety rules
8
The safety hazards associated with the device must be assessed again
8
following installation in the final product.
8
The locally applicable industrial safety regulations are always to be
observed when working on the device.
Keep the workplace clean and tidy. Untidiness in the work area
increases the risk of accidents.
Note the following when working on the device:
; Do not perform any modifications, additions or conversions on the
device without the approval of ebm-papst.
1.4 Voltage
; Check the device's electrical equipment at regular intervals; see
Chapter 5.2 Safety inspection.
; Replace loose connections and defective cables immediately.
DANGER
Indicates an imminently hazardous situation which will result in
death or serious injury if the specified actions are not taken.
Compliance with the instructions is imperative.
WARNING
Indicates a potentially hazardous situation which can result in
death or serious injury if the specified actions are not taken.
Exercise extreme caution while working.
CAUTION
Indicates a potentially hazardous situation which can result in
minor or moderate injury or damage to property if the specified
actions are not taken.
NOTE
A potentially harmful situation can occur and, if not avoided, can
lead to property damage.
DANGER
Electrically charged device
Risk of electric shock
→ When working on an electrically charged device, stand on a
rubber mat.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ebm-papst M4Q045-CA01-75
Summary of Contents for ebm-papst M4Q045-CA01-75
-
Page 1: Table Of Contents
Note the following when working on the device: ; Do not perform any modifications, additions or conversions on the device without the approval of ebm-papst. 1.4 Voltage ; Check the device's electrical equipment at regular intervals; see Chapter 5.2 Safety inspection. -
Page 2: Electromagnetic Radiation
Operating instructions M4Q045-CA01-75 WARNING 1.7 Hot surface Live terminals and connections even with device CAUTION switched off High temperature on motor housing Electric shock Risk of burns → Wait five minutes after disconnecting the voltage at all poles → Ensure sufficient protection against accidental contact. -
Page 3: Intended Use
Operating instructions M4Q045-CA01-75 2. INTENDED USE The device is designed exclusively for use as a drive motor. Any other usage above and beyond this does not conform with the intended purpose and constitutes misuse of the device. Customer equipment must be capable of withstanding the mechanical and thermal stresses that can arise from this product. -
Page 4: Technical Data
Operating instructions M4Q045-CA01-75 3. TECHNICAL DATA 3.1 Product drawing All dimensions in mm. Cable PVC, 3x crimped splices Tightening torque for nut for fastening fan housing or guard grille 2.3 Nm Tightening torque for screw for fastening fan impeller 1.4 Nm Tightening torque for nut for fastening mounting bracket 2.3 Nm... -
Page 5: Nominal Data
With regard to cyclic speed loads, note that the rotating parts of the device are designed for a maximum of one million load cycles. If you have special questions, consult ebm-papst for support. ; Use the device in accordance with its degree of protection. -
Page 6: Connection And Startup
Operating instructions M4Q045-CA01-75 4. CONNECTION AND STARTUP Only connect the device to circuits that can be switched off with an all-pole disconnection switch. 4.1 Mechanical connection 4.2.1 Requirements WARNING ; Check whether the information on the nameplate matches the Hot motor housing connection data. -
Page 7: Connection Diagram
Operating instructions M4Q045-CA01-75 4.4 Connection diagram blue green/yellow brown Item no. 10954-5-9970 · ENU · Change 225340 · Approved 2021-04-28 · Page 7 / 9... -
Page 8: Checking Connections
This also applies for In the event of further malfunctions, contact ebm-papst. devices which have already been equipped with plugs and terminals or similar connectors by the customer. - Page 9 Electrolytic capacitors ● Dispose of electronic components employing the proper procedures for electronic scrap. → Please contact ebm-papst for any other questions on disposal. Item no. 10954-5-9970 · ENU · Change 225340 · Approved 2021-04-28 · Page 9 / 9...
Need help?
Do you have a question about the M4Q045-CA01-75 and is the answer not in the manual?
Questions and answers