Lasko T42905 Operating Manual page 2

IMPORTANT SAFETY INSTRUCTIONS
When using electrical appliances, these instructions and warnings should always be
followed to reduce the risk of fire, electrical shock and injury to persons:
Read all instructions before using this Fan.
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK OR PERSONAL INJURY, ALWAYS
WARNING
FOLLOW THESE IMPORTANT SAFETY INSTRUCTIONS AND WARNINGS:
DO NOT use this Fan to ventilate areas where flammable liquids or vapors are used, stored or are present, including paints,
gasoline, varnishes, floor refinishing products or solvents. ALWAYS read and follow all warnings and instructions on the
containers for these products!
ALWAYS be sure the plug fits tightly into the outlet. When plugs fit loosely into outlets, they may slip partially out of the outlet and
create a poor connection. This may cause outlets to overheat and create a potential fire hazard. Outlets in this condition should
be replaced by a qualified electrician.
ALWAYS unplug the power cord when servicing, cleaning or moving the Fan. DO NOT use the ON/OFF switch as the sole means
of disconnecting power. NEVER leave children unattended when the Fan is on or plugged in. ALWAYS turn off and unplug the
Fan when not in use.
BE CERTAIN that the power source for the Fan is 120V AC. DO NOT plug the Fan into 240V or other power source.
The Blue Plug ™ on your Lasko Fan is a safety feature. It contains a non-replaceable safety device (fuse) that should not be removed
or tampered with. To reduce the risk of fire, electric shock and personal injury, DO NOT attempt to remove, replace, repair or tamper
with the originally supplied plug. If the Fan has stopped functioning, it may be due to the safety device incorporated in this plug.
THIS FAN HAS A POLARIZED PLUG (one blade is wider than the other). This plug is designed to fit into the outlet only one way.
Match the wide blade to wide slot in outlet and FULLY INSERT. DO NOT attempt to bypass or defeat this safety feature. If the
plug does not fit in the outlet, consult a qualified electrician. The outlet may need to be replaced.
CAUTION
• AVOID the use of extension cords, power strips, power taps, outlet style air fresheners or other cord connected device, as these de-
vices may overheat and cause a fire hazard.
• DO NOT route power cord under rugs, carpets, runners or furniture. This may damage the cord or cause it to overheat creating a
fire hazard.
• ALWAYS place the Fan on a stable, flat, level surface while in operation to prevent the Fan from overturning.
• NEVER insert or allow fingers or objects to enter grill openings while Fan is in operation or injury and/or damage to the Fan may occur.
• DO NOT block, cover or obstruct air flow to or from the Fan while in operation.
• DO NOT use this Fan outdoors or near water or wet locations such as a bath tub, pool or hot tub. Use of this Fan in a wet location may
create a shock hazard.
• DO NOT run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture
or appliances. Arrange cord away from traffic area and where it will not be tripped over.
• NEVER use a single extension cord to operate more than one Fan or other electrical device.
• DO NOT use this Fan if it has been damaged or is not functioning properly.
• Remote controls for other appliances or electronic equipment can sometimes interfere with the operation of this Fan. If this occurs,
move the Fan to another location.
• Keep Fan remote control unit away from chairs and your bed where it may be sat or laid upon and inadvertently turn on the Fan.
• THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008). This Fan is not suitable for use in agricultural
facilities including areas where livestock, poultry or other animals are confined. Please refer to National Electric Code (NEC) Article
547-7 (2008), or applicable state or local codes or standards relating to electrical requirements for agricultural buildings.
• THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 500 (2008). This Fan is not suitable for use in hazardous lo-
cations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes or standards relating to electrical
requirements for hazardous locations.
NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harm-
ful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving
antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. The user is cautioned that changes
and modifications made to the equipment without the approval of manufacturer could void the user's authority to operate this equipment.
SAVE THESE INSTRUCTIONS
NEW 3/19
WARNING
2
ENSAMBLAJE
1. Para facilitar el armado, recueste el Ventilador de modo que la parrilla
negra y el tablero de control den hacia arriba.
2. Arme las Mitades de la Base de Apoyo encastrando las Puntas de la
Base de Apoyo A con los Orificios para Puntas en la Base de Apoyo B.
Conecte el Cable Eléctrico a través del orificio grande en el centro de
la Montura de la Base de Apoyo. (Figura 1)
3. Asegure (2) #8 X 3/8" Tornillos en los dos orificios externos en la parte
inferior de la Base. (Figura 2)
4. Alinee la Montura de la Base de Apoyo con la Base del Motor,
teniendo en cuenta que la ranura del cable en la parte inferior de la
montura de la base de apoyo debe apuntar hacia la parte posterior
del Ventilador. Adose la Montura de la Base de Apoyo a la Base del
Motor con (4) Tornillos Largos M5 de 1/2". Cerciórese de alinear la
Llave del Conjunto de la Base de Soporte con la Muesca Localiza-
dora de la Base Del Motor. (Figura 1) Suavemente tire del Cable
Eléctrico para evitar que quede flojo y colóquelo en el Orificio de
Colocación del Cable. (Figura 3)
Base de Soporte A
Base de
Soporte B
Figura 1
Conjunto de la
Base de Soporte
#8 X 3/8"
Tornillos
Figura 2
Conjunto de la
Base de Soporte
M5 X 1/2"
Tornillos
Figura 3
T42905ES NEW 3/19
MODELO T42905
OPERACIÓN
Este ventilador puede operarse con los controles manuales que se encuen-
tran en la parte superior de la unidad (Figura 3) o mediante los controles
Bluetooth ® en su smartphone (Figura 4). Todas las funciones realizadas
con los controles Bluetooth
manuales. Para ver una descripción detallada de la sincronización Blue-
tooth ® , consulte la guía de inicio rápido.
1. Coloque el ventilador sobre una superficie firme y nivelada.
2. Conecte el cable eléctrico a un tomacorriente de 120 volts.
De no encajar firmemente en el tomacorriente, podrían de-
slizarse parcial o completamente fuera del tomacorriente
apenas con un ligero movimiento del cable conectado. Los
receptáculos en esta condición pueden sobrecalentarse y
constituir un grave riesgo de incendio; si está cubierto por
una cortina, el peligro de incendio es aún mayor.
3. Suministre corriente eléctrica al ventilador al presionar el Botón de Encen-
dido ( ). El ventilador operará inicialmente en velocidad alta, velocidad 3.
4. VELOCIDAD DEL VENTILADOR: Ahora usted puede ajustar la veloci-
Cable Eléctrico dad del ventilador al nivel deseado, 3, 2, o 1 oprimiendo el Botón de
Velocidad ( ).
5. OSCILACIÓN: Presione el Botón de Oscilación (
la función de oscilación. La función de oscilación puede utilizarse con
cualquier modo de velocidad y/o de temporizador.
Llave
6. FUNCIÓN DE TEMPORIZADOR: Este ventilador está equipado con
un temporizador. El temporizador se puede configurar para 1-7 horas.
Continúe pulsando el Botón del Temporizador ( ) para llegar a la con-
figuración de tiempo deseada. Para cancelar el temporizador, pulse el
Botón de Temporizador ( ) hasta que las luces se apaguen.
Copas
7. Después de apagar el ventilador, desconecte la unidad del tomacor-
riente eléctrico.
Botón
Temporizador
Figura 4
Cable Eléctrico
Botón de
Temporizador
Botón de
Oscilación
Añadir
Orificio de
Dispositivo
Colocación
del Cable
Cable Eléctrico
Figura 5
7
®
funcionan idénticamente a los controles
Asegúrese que el enchufe encaje
firmemente en el tomacorriente.
) para iniciar y detener
Botón de Bluetooth ®
Botón de
Oscilación
Botón de
Encendido
Botón de Velocidad
Personalizar
Botón de
Encendido
Botón de
Velocidad
del Ventilador
Información
Home
T42905ES