1. Manuals
  2. Brands
  3. Russell Taylors Manuals
  4. Steam Cleaner
  5. i1
  6. Product manual

Russell Taylors i1 Product Manual

Hide thumbs

Advertisement

Table of Contents

i1 Product Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the i1 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Russell Taylors i1

  • Page 1 Product Manual...
  • Page 2 Important Information Before using this product, please read all the contents of this manual carefully and follow the steps of this manual to install the product. Any operation not in accordance with the instructions may cause damage to the product or serious personal injury. This product is only suitable for use in a household environment, not for industrial or outdoor use.

  • Page 3: About Cleaning Solution

    Important Information >>>About The Scope Of Product Use >>>About Cleaning Solution ● This product is suitable for hard floor, including waxed floor, stone ●If a large amount of cleaning solution is added, it will grinding floor, rubber floor, marble floor, granite floor, terrazzo floor, solid produce excess foam when used, which may penetrate into the wood floor, composite floor, bamboo floor and various mirror tiles, motor and cause damage.
  • Page 4 Product Self-cleaning button ( Press 3 seconds to turn on/off voice prompt ) Handle Power switch Clean water tank inlet Clean water tank Dirty water tank release button Dirty water tank Dirty water tank handle Mobile wheel Brush cover Brush roller...
  • Page 5 Product Overview/Product Introduction Brush roller Adaptor Cleaning brush HEPA Filter Accessory bracket Charging base Machine body...
  • Page 6 Product Overview/Product Disassembly click To disassemble, please press the release with Insert the end of the handle vertically into a hard object into the hole on the back of the the fuselage jack. After hearing the click, fuselage, and pull out the handle of the ensure that the handle is firmly and machine upward.
  • Page 7 Product Overview/Product Disassembly click If you want to take out the clean water tank, pull the If you want to install the clean water tank, put it clean water tank upward to take out the clean water with the slot and press it down to hear a click to tank install successfully.
  • Page 8 Product Overview/Product Disassembly To remove the brush cover, first apply your When installing, firstly apply your finger to the position as finger to the position as shown in the picture shown in the picture and press the release buttons at and press the release buttons at both ends both ends with your thumb and forefinger at the same with your thumb and forefinger to lift the...
  • Page 9 Product Overview/Product Parameters ▲Before use, please check whether your floor washer The machine has an upright switch,please tilt after starting the machine,but do not has power. If not, please tilt the machine more than 142 degrees, so charge it in time (refer to as not to cause water leakage.
  • Page 10 Product Overview/Product Instruction click 2.Open the upper cover 3.Tighten the upper 4. Install the clean water 1.Gently pull out of the clean water cover of the clean tank back to the machine. the clean water bucket, and add proper water tank to ensure it The installation will be tank: amount of clean water...
  • Page 11 Product Overview/Product Instruction First, put the machine into the charging base, connect one end of the charger to the charging base, and the other end to the home socket. The power cord can be folded up when no charge is required. When charging, please keep the machine upright and close to the corner to avoid tripping and other injuries.

  • Page 12: Maintenance

    Maintenance It is recommended that you have regular maintenance on its 1.Please stop the machine before cleaning (Pic 1). components , 2.Scrub with water or neutral detergent, be sure to in order to avoid the using function of wring out the cleaning cloth before scrubing, do not machine let water get inside the electrical parts of the Note...
  • Page 13 Maintenance 1.Please clean the dirty pipes regularly to avoid blocking and affecting the use.(Pic 1) 2.Please take down the dirty water tank, wipe the dirt sensor in the pipe with a wet rag or use the cleaning tools provided to clean the dirt inside the pipe before use.(Pic 2).
  • Page 14 Maintenance 1.If the dirty water tank is blocked, clean it in time. 2.Remove the top cover of the dirty water tank (Pic. 1) and clean with water (Pic. 2). 3.After cleaning, load the dirty water tank. It is recommended to clean and dry the filter after each use to keep it clean and tidy.
  • Page 15 1.Put the machine back to the base after use, press self-cleaning Note ！ button to start self-cleaning. ------------------- 2.After the self-cleaning is complete, the machine will enter the charging state. It is recommended that you have regular maintenance on its components. in order to avoid the using function of machine in order to avoid the using function of machine...
  • Page 16 Maintenance It is recommended to clean and dry the brush roller after use to keep it clean and tidy. Note ！ ------------------- If residual stains are found at the mouth of suction nozzle, please wipe 1.Pull up the handle on the left end of the brush roller and remove it (Pic 1). with wet cloth, do not wash with 2.Remove the brush roller handle and use the brush roller cleaning tool to remove tangled hair or debris on water.

  • Page 17: Common Problems

    Troubleshooting Common problems Solution Product out of power or low battery Please use after full of battery capacity. Full of dirty water in the tank Take out the dirty water tank and pour out the dirty water. Installation not in place of brush roller, Reinstall brush roller cover,dirty water tank Clean the suction nozzle or pipe...

Table of Contents