Illinois Tool Works Paslode 903800 Operating Manual

Cordless 16 gauge straight finish nailer

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

IMPORTANT!

DO NOT DESTROY

It is the customer's responsibility to have

all operators and service personnel read

and understand this manual.

Printed in U.S.A.

902017-7

03/10

Part No. 903800

OPERATING MANUAL

www.paslode.com

Table of Contents

Need help?

Do you have a question about the Paslode 903800 and is the answer not in the manual?

Questions and answers

Summary of Contents for Illinois Tool Works Paslode 903800

Page 1 Part No. 903800 OPERATING MANUAL IMPORTANT! DO NOT DESTROY It is the customer's responsibility to have all operators and service personnel read and understand this manual. Printed in U.S.A. © 2010 Illinois Tool Works, Inc. www.paslode.com 902017-7 03/10...
Page 2: Introduction And Warranty
Introduction and Warranty Paslode Cordless 16 Gauge Straight The Cordless Finish Nailer should be handled like other power fastening tools that you use. Like most tools, when Finish Nailer Operating Manual used improperly injury could result . If you are going to allow others to use the Cordless Finish Nailer, it is your This manual is intended to acquaint you with the Paslode responsibility to make sure that they also read and comply...
Page 3: Table Of Contents
The battery charger system meets all safety requirements for power tools. is a trademark Paslode An Ilinois Tool Works Company 888 Forest Edge Drive Vernon Hills, Illinois 60061 www.paslode.com Power Nailers are made in the U.S.A. ® Paslode is a member of: Copyright © 2008 Illinois Tool Works, Inc.
Page 4: An Overview Of The Paslode Cordless 16 Gauge Straight Finish Nailer
Overview of the Paslode Cordless 16 ga. Straight Finish Nailer Description Specifications Dimensions: Weight- 4 lbs 12oz. with battery The Paslode Cordless 16 ga. Straight FinishNailer is a self- Height 11-3/4 inches contained, fully portable nailer that uses liquid hydrocarbon Length 10-1/2 inches fuel to power a unique linear drive internal combustion...
Page 5 The following safety instructions have been included in this booklet to provide you with basic information necessary for WARNING safe operation of the Paslode Cordless 16 ga. Straight Finish Nailer. DO NOT ATTEMPT TO OPERATE THIS TOOL UNTIL YOU HAVE READ AND UNDERSTAND ALL Do not expose the tool to SAFETY PRECAUTIONS AND MANUAL INSTRUCTIONS.
Page 6: Safety Instructions
Safety Instructions 7. NEVER OPERATE THE TOOL WITH THE WORK CONTACTING ELEMENT REMOVED OR DISABLED. WARNING This device helps reduce the possibility of accidental fastener discharge by preventing the tool from operating Always wear EYE and until it is completely against the work surface. EAR safety gear when working with or in the NEVER operate the tool if the work contacting element...
Page 7 Safety Instructions 15. PROPERLY STORE FUEL CELL. 12. NEVER DRIVE FASTENERS INTO AREAS WITH CONCEALED HAZARDS. Always check the area behind the work surface for WARNING electrical wiring, gas pipes, water pipes, sewer drains or other potential hazards. Always store fuel cells where they will not be 13.
Page 8: Battery And Charger
Battery and Charging System Battery and Charging System Charging Instructions The Paslode Cordless tools come with a recharge- 1. Remove wall mount unit with the orange label from able battery and its own charging system. This the tool case and plug into a 120V AC outlet. Set charging system is the only one that will work with orange charger on a stable surface and insert wall the Paslode batteries (either round or oval ).
Page 9 Battery and Charging System Battery Indicator Light On the right side of the handle is a small plastic lens. This is the battery indicator light. When you insert a fully-charged battery into the tool, you will see a blinking green light. If the indicator light blinks red, recharge the battery.
Page 10: Fuel Cell And Metering Valve
Fuel Cell and Metering Valve Fuel Cell There is a second container inside the fuel cell. The inner container holds the fuel. The space between the inner container and the outer cylinder is filled with a gas, called the propellant, which is under pressure. DANGER To eject the fuel, propellant pressure squeezes the inner E X P L O S I O N / F I R E...
Page 11 Fuel Cell and Metering Valve Installing Metering Valve to Fuel Cell Prior to Use To install the metering valve to a fuel cell: 1. Press downward on the front side of the valve (stem side) until it seats. 2. Press downward on the rear side of the valve until it seats. 3.
Page 12 Fuel Cell and Metering Valve Inserting Fuel Cell As you slide the metering valve/fuel cell assembly into the Cordless Finish Nailer, you will notice a yellow adapter at Inserting the metering valve/fuel cell assembly into the the top of the cylinder pocket. As shown in the illustration, Cordless Finish Nailer is very simple.
Page 13: Preparing The Paslode Cordless 16 Gauge Straight Finish Nailer For Use
Preparing the Paslode Cordless 16 ga. Straight Finish Nailer Fasteners Paslode Cordless 16 ga. Straight Finish Nailer and Outdoor Weather The Paslode Cordless 16 ga. Straight Finish Nailer drives ® Paslode 16 gauge straight fasteners designed to be Use the Cordless Finish Nailer outdoors, in dry used with the tool.
Page 14: Paslode Cordless 16 Gauge Straight Finish Nailer Operation
Paslode Cordless 16 ga. Straight Finish Nailer Operation Operation: PRESS WORK – CONTACTING ELEMENT AGAINST THE WORK SURFACE. Fan motor starts, fuel is injected into combustion Turn chamber and adjustment mixed with air by wheel in the fan. either direction SQUEEZE TRIGGER Spark plug ignites...
Page 15: Fasteners And Applications
Fasteners and Applications Applications The Paslode Cordless 16 ga. Straight Finish Nailer is suited for a variety of applications. These include securing door and window casings; attaching baseboards where walls meet floors; attaching moldings where walls meet ceilings; securing paneling; securing chair rails, picture molding and other decorative trim. Fasteners The Paslode Cordless 16 ga.
Page 16: Servicing
Servicing Restrict Field Service to the Following Fuel Cell Check CHECKING THE ENERGY LEVEL OF THE BATTERY If the Cordless Finish Nailer's fan operates and the indicator light is green, but the tool will not cycle or does not drive RECHARGING THE BATTERY fasteners completely, check the fuel cell.
Page 17 Servicing Air Filter When you get home: Place the battery in its charger if it needs charging as Open the grille by pressing slightly above the adapter and indicated by the red charge light on the handle. pivoting the grille open. The air filter simply lifts out. 2.
Page 18: Troubleshooting
Troubleshooting Preparing Tool for Operation - Battery/Charger Problems Battery does not appear to accept charge Inoperative indicator lights on charger, or Try battery in tool after a full charge cycle. when battery is plugged into the charger. defective charger. If tools indicator light is red, charger not working properly.
Page 19 Troubleshooting Normal Stage of Operation Tool operates properly, but fasteners do not Work-contacting element requires adjustment. Adjust work contacting element. drive fully. Fuel cell is low. Check fuel cell and replace as required. There may be loss of seal in combustion Press work contacting element against chamber.
Page 20 An Illinois Tool Works Company 888 Forest Edge Drive Vernon Hills, Illinois 60061 Printed in U.S.A. www.paslode.com © 2010 Illinois Tool Works, Inc.