Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Samsung DV45DG6000 Series
Summary of Contents for Samsung DV45DG6000 Series
- Page 1 Dryer User manual DV45DG6000** Untitled-2 1 2024-06-27( ) 6:30:09...
-
Page 2: Table Of Contents
Contents Safety information What you need to know about the safety instructions Important safety symbols CALIFORNIA PROPOSITION 65 WARNING IMPORTANT SAFETY INSTRUCTIONS Warnings Cautions Regulatory notice FCC Notice IC Notice Open Source Announcement Installation requirements Key installation requirements Location considerations Ducting requirements (Not applicable to ventless (heat pump) models) Exhausting requirements (Not applicable to ventless (heat pump) models) Gas requirements (Not applicable to ventless (heat pump) models) - Page 3 Operations Control panel Simple steps to start Cycle overview Cycle chart Cycle guide Special features SmartThings Maintenance Emptying the water tank Installing the micro soft filter (Optional Filter) Cleaning Troubleshooting Checkpoints Information codes Specifications Fabric care chart Protecting the environment Specification sheet English 3 Untitled-2 3...
-
Page 4: Safety Information
Safety information Congratulations on your new Samsung dryer. This manual contains important information on the installation, use and care of your appliance. Please take some time to read this manual to take full advantage of your dryer’s many benefits and features. - Page 5 WARNING - Risk of Fire • Clothes dryer installation must be performed by a qualified installer. • Install the clothes dryer according to the manufacturer’s instructions and local codes. • Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers.
- Page 6 Safety information WARNING - To reduce the risk of fire or explosion: • Do not dry items that have been previously cleaned, washed, soaked, or spotted with gasoline, dry cleaning solvents, or other flammable or explosive substances. They emit vapors that could ignite or explode.
-
Page 7: California Proposition 65 Warning
WARNING - Fire or explosion hazard • Failure to follow safety warnings exactly could result in serious injury, death or property damage. • Do not store or use gasoline or other flammable vapors and liquids near this or any other appliance. •... -
Page 8: Important Safety Instructions
Safety information IMPORTANT SAFETY INSTRUCTIONS WARNING To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: 1. Read all instructions before using this appliance. 2. Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapours that could ignite or explode. -
Page 9: Warnings
Warnings WARNING • Ensure pockets are free of small, irregularly shaped hard objects and foreign material, i.e. coins, knives, pins, etc. These objects could damage your dryer. • Gas leaks may occur in your system, resulting in a dangerous situation. Cautions CAUTION •... - Page 10 Safety information • Residual oil on clothing can ignite spontaneoulsy. The potential for spontaneous combustion increases when items containing vegetable oil or cooking oil are exposed to heat. Heat sources such as your dryer can warm these items, allowing an oxidation reaction in the oil to occur. Oxidation creates heat. If this heat cannot escape, the items can become hot enough to catch fire.
-
Page 11: Regulatory Notice
Regulatory notice FCC Notice CAUTION Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of FCC Rules. Operation is Subject to following two conditions: 1. -
Page 12: Ic Notice
Regulatory notice IC Notice The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. -
Page 13: Open Source Announcement
Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: The official Declaration of conformity may be found at http://www.samsung.com, go to Support > Search Product Support and enter the model name. -
Page 14: Installation Requirements
Installation requirements Read through the following instructions before installing the dryer and keep this manual for future reference. WARNING Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing. Service Personnel - Do not contact the following parts while the appliance is energized: Control board and inlet valve. - Page 15 Dimensions Type Front loading dryer Models DV45DG6000** A. Overall height 38.7 (984) B. Width 27 (686) Dimensions (in. (mm)) C. Depth with the door open 54.2 (1378) D. Depth 33.2 (844) English 15 Untitled-2 15 2024-06-27( ) 6:30:10...
- Page 16 Installation requirements Clearance requirement This clearance requirement is applicable for dryers only. NOTE • For the washer's clearance requirement, see the washer's user manual. • If the washer and dryer have different clearance requirements, use the one with the larger value. Alcove or closet installations WARNING •...
- Page 17 Undercounter installation 39.7 in. (1009 mm) 1 in. (25 mm) 1 in. (25 mm) Pedestal installation 2 in. (50 mm) 6 in. (152 mm) 52.8 in. (1341 mm) English 17 Untitled-2 17 2024-06-27( ) 6:30:10...
- Page 18 NOTE Stacking (SKK-8HK) Many of Samsung's washers and dryers can be stacked to maximize usable space. You can purchase an optional stacking kit from your Samsung retailer. For details about stacking and compatible models, refer to the user manual included in the stacking kit you purchase.
-
Page 19: Ducting Requirements (Not Applicable To Ventless (Heat Pump) Models)
Ducting requirements (Not applicable to ventless (heat pump) models) Use only for short-run Recommended installation Weather hood type 4” (10.2 cm) 2.5” (6.4 cm) No. of 90° elbows Rigid Rigid 80 ft. (24.4 m) 74 ft. (22.6 m) 68 ft. (20.7 m) 62 ft. -
Page 20: Exhausting Requirements (Not Applicable To Ventless (Heat Pump) Models)
Installation requirements Exhausting requirements (Not applicable to ventless (heat pump) models) The dryer must not be exhausted into a chimney, a wall, a ceiling, an attic, a crawl space, or a concealed space of a building. Exhausting the dryer to the outside will prevent large amounts of lint and moisture from being blown into the room. -
Page 21: Gas Requirements (Not Applicable To Ventless (Heat Pump) Models)
Gas requirements (Not applicable to ventless (heat pump) models) WARNING • Use only natural or LP (liquid propane) gases. • The installation must be conformed with local codes, or in the absence of local codes, with the national fuel gas code, ANSI Z223.1/NFPA 54, latest revision (for the UNITED STATES), or with the natural gas and propane installation code, CSA B149.1 (for Canada). -
Page 22: Electrical Requirements
Installation requirements Electrical requirements The wiring diagram is located on the plate under the control panel or rear frame. WARNING When local codes allow, you can connect the dryer’s electrical supply with a new power supply cord kit, marked for use with a dryer, that is U.L. listed and rated at a minimum of 120 / 240 volts, 30-amperes with three No. - Page 23 • If a power cord is not used and the electric dryer is to be permanently wired, the dryer must be connected to a permanently grounded metal wiring system, or an equipment grounding conductor must be run with the circuit conductors and connected to the equipment grounding terminal or lead on the dryer.
-
Page 24: Installation
What’s included Make sure all the parts are included in the product package. If you have a problem with the dryer or the parts, contact a local Samsung customer center or the retailer. 01 Water tank 02 Door... - Page 25 • The stacking kit allows the dryer to be stacked on top of a washer. Please note that the stacking kit can only be used with Samsung washers and dryers. To purchase a stacking kit above, contact a Samsung service center or local appliance retailer. The stacking kit differs with the washer model.
-
Page 26: Step-By-Step Installation
Installation Step-by-step installation Make sure you have a qualified technician install the dryer. Step-by-step installation instructions start below. • Do not remove the protective film on the door before completing the product installation. If you remove the protective film before the installation is complete, the door may get scratched or damaged during installation. - Page 27 STEP 3 Connect the electrical wiring (for electric models) Before connecting the electrical wiring, make sure you have read the “Electrical requirements” section on page 22. 3-wire system 1. Loosen or remove the screws from the center terminal block. 2. Connect the neutral wire (white or center wire) of the power cable to the center, silver-colored terminal screw of the terminal block.
- Page 28 Installation 4-wire system 1. Remove the external ground connector’s screw and connect the ground wire (green or unwrapped) of the power cable to the screw. CAUTION To connect the ground wire to the neutral position without through contact A (cabinet ground), contact a technician.
- Page 29 STEP 4 Level the dryer To ensure optimal performance, the dryer must be level. Using a level (A), check if the dryer is level side to side and then front to back. If the dryer is not level, turn the leveling feet (B) clockwise to lower the dryer or counterclockwise to raise the dryer.
-
Page 30: Connect The Drain Hose
Installation STEP 5 Power on (for gas models) Make sure all gas connections, the exhaust line, and all wiring are connected correctly. Then, plug the power cord into a power source and check the dryer’s installation and operation using the final checklist in Step 6 below. - Page 31 1. Remove the water tank drain hose from the drain water outlet (A), and then insert it to the holder (B). 2. Insert one end of the accessory hose (long drain hose) into the drain water outlet (A). 3. Place the other end (outlet) of the accessory hose at least 2.8 in.
- Page 32 Installation CAUTION • Place the other end (outlet) of the accessory hose about 70 mm away from a drain hole. Do not insert the end (outlet) of the accessory hose into a sewer. A sewer smell may flow into the dryer. •...
-
Page 33: Installation Checklist
Installation checklist • The dryer is plugged into a properly grounded outlet. • All packaging material is completely removed and properly disposed. • The dryer is level and standing firmly on the floor. • The long drain hose is installed if you want water captured by the drying process drained automatically. •... -
Page 34: Exhaust Ducting Guide (Not Applicable To Ventless (Heat Pump) Models)
Installation Exhaust ducting guide (Not applicable to ventless (heat pump) models) Ducting 1. Make sure the dryer is installed properly so the air exhausts freely. 2. Use 4-inch rigid metal ducts. Tape all joints including the dryer connection. Never use lint-trapping screws. - Page 35 2. Remove the six screws fastening the door glass at the inner side of the door. Remove the bottom three screws first. 3. Disassemble the door glass. CAUTION Be careful not to drop it during disassembling. • You may damage the parts, and broken glass parts may lead to injury.
- Page 36 Installation 5. Remove the two screws that are above and below the cut-out in the front frame. 6. Remove the two screws above and below the lever holder on the opposite side of the door opening. 7. Remove the two screws that hold the lever holder in place, and then remove the lever holder.
- Page 37 9. Remove the single screw from the back of the door hinge. NOTE This is the screw that supports the door against the frame so you can unscrew or screw in the hinge without needing to support the door yourself. 10.
- Page 38 Installation 13. Re-attach the remaining screws to the remaining holes above and below the lever holder, and then tighten. 14. Attach the door on the opposite side and put the door glass back in its place. 15. Fasten the door glass with the six screws. NOTE Firmly hold the door glass to prevent from dropping it while you fasten it with the screws.
-
Page 39: Before You Start
Before you start Here are a few things you should know before starting your dryer. Sort and load • Put one wash load in the dryer at a time. • Do not mix heavy and lightweight items. • To improve drying efficiency for one or two items, add a dry towel to the load. •... -
Page 40: Operations
Operations WARNING To reduce the risk of fire, electric shock, or injury, read the “Safety information” before operating this appliance. Control panel Turn the Cycle Selector to select a desired cycle. When a cycle is selected, the cycle indicator lights up. 01 Cycle Selector •... - Page 41 You can turn on or off the sound from the dryer. After connecting the Tumble Dryer to your home network using the Samsung Smart Washer/Dryer app, you can control the dryer remotely. 10 Smart Control When started, the Smart Control indicator blinks. The dryer enters waiting mode and waits for remote commands.
-
Page 42: Simple Steps To Start
Operations Icon description This icon appears when the dryer operates the cycle which senses the Sensor Dry internal humidity to determine the drying time. You can save energy for your dryer through the AI Energy Mode provided by SmartThings Energy Service. When AI Energy Mode is applied, this icon is displayed and shows the saved energy compared AI Energy Mode to when AI Energy Mode was not used after the drying is completed. -
Page 43: Cycle Overview
PERM PRESS fabrics automatically. DELICATES For heat-sensitive items at a low drying temperature. • Select to choose from more cycles available on the Samsung Smart Washer/Dryer app on your smartphone. DOWNLOADED • Available cycles: ECO NORMAL, SHIRTS, DENIM, WOOL, AIR BEDDING CARE, DOWN JACKET CARE, OUTDOOR CARE •... -
Page 44: Cycle Chart
Operations Manual Dry You can change the drying settings manually to your preference. Cycle Description Use to set a desired dry time. Turn the Cycle Selector to select TIME DRY and tap Time to set the drying time between 20 minutes and 240 minutes. Tap Time repeatedly to select the available time options in this order: 20 / 40 / 60 / 90 / 120 / 150 / 180 / 240. - Page 45 NOTE : factory setting, : can be selected Options Cycle Time setting Wrinkle Prevent Damp Alert NORMAL HEAVY DUTY SANITIZE BEDDING Standard PERM PRESS DELICATES TOWELS ACTIVEWEAR QUICK DRY ...
-
Page 46: Cycle Guide
Operations Cycle guide The best way to dry items is to follow the instructions on the care label. If no drying instructions are provided, see the following table for reference. Cycle Description Follow the care label instructions or dry using BEDDING. Bedspreads &... -
Page 47: Special Features
• To unmute the sound, Press again Sound Off. Smart Control To enable this function, you must first download the Samsung Smart Washer/Dryer app at the Play Store or the App Store and install it on a mobile device featuring a camera function. The Smart Control function has been optimized for Galaxy &... -
Page 48: Smartthings
• This appliance supports the Wi-Fi 2.4 GHz protocols. Download On an app market (Google Play Store, Apple App Store, Samsung Galaxy Apps), find the SmartThings app using the search term “SmartThings”. Download and install the app on your device. -
Page 49: Maintenance
Maintenance Emptying the water tank Empty the water tank after each use to prevent leaks. 1. Remove the water tank (A) from the dryer. Pull the water tank handle with one hand until the tank is halfway out. Once the water tank is halfway out, support the bottom of the tank with the other hand and pull it slowly with both hands. -
Page 50: Installing The Micro Soft Filter (Optional Filter)
Maintenance Installing the micro soft filter (Optional Filter) You can install the provided micro soft filter (Optional Filter) to prevent dust accumulation on the heat exchanger. 1. Gently press the top part of the outer cover (A) to open. 2. Unlock the inner cover fixers (B), and then pull the inner cover to remove. -
Page 51: Cleaning
4. Reinsert the inner cover to its original position, and then lock the fixers. 5. Close the heat exchanger’s outer cover. Cleaning WARNING • Do not clean the dryer by directly spraying water onto the dryer. • Do not clean the dryer with benzene, thinner, alcohol, or acetone. This may cause discoloration, deformation, damage, electric shock, or fire. - Page 52 Maintenance Lint filter Clean the lint filter after each use. 1. Open the dryer door, grab the top of the lint filter, and pull to remove the filter. Do not detach the rubber sealing after removing the filter. 2. Open the outer filter and remove the inner filter (A). 3.
- Page 53 NOTE To clean the filters thoroughly, clean the filters in running water, and then dry them completely. 5. Put the inner filter into the outer filter, and then reinsert the lint filter into the original position. CAUTION • Clean the lint filter after each load. Otherwise, the drying performance may decrease. •...
- Page 54 Maintenance Heat exchanger When it is time to clean the heat exchanger, the Heat Exchanger Clean icon ( ) appears on the display. A dirty heat exchanger will hinder the product’s performance and should be cleaned regularly. NOTE • Water droplets can form around the heat exchanger due to condensation caused by a temperature difference.
- Page 55 4. Clean the inner cover with a smooth, damp cloth. There may be moisture and/or foreign substances around the inner cover. 5. Reinsert the inner cover to its original position, and then lock the fixers. 6. Close the heat exchanger’s outer cover. English 55 Untitled-2 55 2024-06-27( )
- Page 56 Maintenance Micro soft filter (Optional Filter) When it is time to clean the Micro soft filter (Optional Filter), the icon remains on the display and does not turn off. A dirty Micro soft filter (Optional Filter) will hinder the product’s performance and should be cleaned regularly.
-
Page 57: Troubleshooting
Troubleshooting Checkpoints If you encounter a problem with the dryer, first check the table below and try the suggestions. Problem Action • Make sure the dryer is plugged in. • Make sure the door is properly closed. • Check the fuse or reset the circuit breaker. Dryer does not start. - Page 58 If the hose is frozen, submerge it in warm water to allow the water inside the hose to melt and drain out. Reconnect the hose and check for proper draining. If a problem persists, contact a local Samsung service center. English Untitled-2 58...
-
Page 59: Information Codes
Continuous button press detection inspection BC2/BC4 • Check to see if the button is stuck. • In case of unresolved, contact a Samsung service center. If any information code keeps appearing on the display, contact a Samsung service center. English 59 Untitled-2 59 2024-06-27( ) -
Page 60: Specifications
Specifications Fabric care chart The following symbols provide garment care direction. The clothing care labels include symbols for drying. The use of symbols ensures consistency among garment manufacturers of domestic and imported items. Follow care label directions to optimize garment life and reduce laundering problems. Tumble Dry Cycles Normal Permanent Press... -
Page 61: Protecting The Environment
Protecting the environment This appliance is manufactured from recyclable materials. If you decide to dispose of this appliance, please observe local waste disposal regulations. Cut off the power cord so that the appliance cannot be connected to a power source. Remove the door so that animals and small children cannot get trapped inside the appliance. - Page 62 Warranty service can only be performed by a SAMSUNG authorized service center. The original dated bill of sale and/or proof of delivery must be presented upon request to SAMSUNG or SAMSUNG’s authorized service center to receive warranty service.
- Page 63 Visits by an authorized servicer to explain product functions, maintenance or installation are not covered by this limited warranty. Please contact SAMSUNG at the number below for assistance with any of these issues.
- Page 64 LOSS OF REVENUE OR PROFITS, FAILURE TO REALIZE SAVINGS OR OTHER BENEFITS REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS BASED, AND EVEN IF SAMSUNG HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Some states do not allow exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.
- Page 65 Warranty service can only be performed by a SAMSUNG authorized service center. The original dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or SAMSUNG’s authorized service center. SAMSUNG will provide in-home service during the warranty period at no charge, subject to availability within the Canada.
- Page 66 (English) www.samsung.com/ca_fr/support (French) Visits by a Service Engineer to explain functions, maintenance, or installation is not covered by warranty. Please contact the Samsung call center at the number above for help with any of these issues. English Untitled-2 66...
- Page 67 Memo Untitled-2 67 2024-06-27( ) 6:30:25...
- Page 68 If you change the factory default setting or enable other features, power consumption could increase and exceed the limits qualified for ENERGY STAR. QUESTIONS OR COMMENTS? COUNTRY CALL OR VISIT US ONLINE AT U.S.A 1-800-SAMSUNG (726-7864) www.samsung.com/us/support www.samsung.com/ca/support (English) CANADA 1-800-Samsung (726-7864) www.samsung.com/ca_fr/support (French) Untitled-2 68 2024-06-27( )
Need help?
Do you have a question about the DV45DG6000 Series and is the answer not in the manual?
Questions and answers