H-KING PARAMOTOR V2 Instruction Manual
  1. Manuals
  2. Brands
  3. H-KING Manuals
  4. Aircrafts
  5. PARAMOTOR V2
  6. Instruction manual

H-KING PARAMOTOR V2 Instruction Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

INSTRUCTION MANUAL
Please read this manual carefully before operating this plane.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PARAMOTOR V2 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for H-KING PARAMOTOR V2

Summary of Contents for H-KING PARAMOTOR V2

  • Page 1 INSTRUCTION MANUAL Please read this manual carefully before operating this plane.

  • Page 2: Table Of Contents

    Features Specifications Required Warnings and Safety notes Contents General assembly 4 - 16 Radio setup 17 - 18 Attaching the Parawing 19 - 20 Safety instructions Flying the Paramotor V2 22 - 23 Recommended accessories 24 - 26 Spare Parts...

  • Page 3: Introduction

    INTRODUCTION Following on from the incredible success of the first H-King Paramotor comes this V2. This version sports a new, much more efficient, stable, larger-span parafoil wing in a vibrant color scheme. This makes it so much easier to launch and fly and adds much more stability when flying than the previous version offered.

  • Page 4: Required

    REQUIRED • 1 x 3ch or more computer transmitter with the ability to mix channels and set control curves • 1 x 3ch or more receiver • 1 x 3S (11.1v) 4000~6000mAh LiPo battery and charger Warnings and Safety notes WARNINGS AND SAFETY NOTES •...

  • Page 5: Contents

    CONTENTS OF KIT 1. Gondola 6. Propeller Guard Supports 2. Main Landing Gear 7. Propeller Guard 3. Parafoil Storage Bag 8. Flybar w/LED Light Bar 4. Parafoil Wing 9. Servo Control Arms 5. 10x4.7 Propeller 10. Accessory Pack...

  • Page 6: General Assembly

    GENERAL ASSEMBLY Step 1: Remove the undercarriage retaining bracket. Step 2: Fit the retaining bracket over the undercarriage wire.
  • Page 7 Step 3: Use the hex head screws to refit the undercarriage bracket with the undercarriage wire positioned between the bracket and the base of the airframe. Step 4: Refit the nyloc nuts and tighten the assembly.
  • Page 8 Step 5: At this point we need to remove the motor and motor mount. The reason for this is that the aluminum propguard supporting arms have to be installed behind the mount. Step 4: Refit the nyloc nuts and tighten the assembly.
  • Page 9 Step 6: Push the hex screws through and remove the motor and motor mount completely, this makes fitting the supports easier.
  • Page 10 Step 7: Clip the 4 prop guard support arms into the slots in the rear of the motor mount. These can be quite a tight fit so you may need to squeeze them fully home with a pair of pliers or similar tool. Assembly should look like this when all 4 are clipped into position.
  • Page 11 Step 8: As the following pictures show, refit the motor and motor mount, clamping the prop guard supports between the airframe and the motor mount.
  • Page 12 Step 9: Fit the flybar to the front of the airframe using the longer bolts through the top holes of the motor mount.
  • Page 13 Note: Do not tighten the nuts until you have all 8 bolts through the mount and frame.. Step 10: The prop guard is aerofoiled, please ensure you fit it the correct way around, see picture above.
  • Page 14 Step 11: Clip all 4 of the prop guard supports into the slots on the prop guard. These can be quite a tight fit, so use some pliers to ease them into the slots. Step 12: Feed a cable tie through the hole in the prop guard where the support clips to the guard.
  • Page 15 Step 13: Do this to all 4 supports and tighten the cable ties to secure the prop guard. Make sure you remove the excess length of cable tie once tightened. Step 14: Check the balance of the propeller then fit the assembly as shown.
  • Page 16 Step 15: Tighten the prop nut using the method shown in the picture above. Step 16: The shackles will end up going through the outer holes either side of the flybar after passing through the riser lines. This is shown in more detail further on in the manual when you attach the parawing.
  • Page 17 Step 17: Set up your radio and connect the servos to the receiver. Power up the receiver and center the roll and pitch servos (watch the set up video before you do this part). Fit the servo arms with the pre-fitted cranks onto the splines of the servos.
  • Page 18 Step 18: Fit the servo arms with the pre-fitted cranks onto the splines of the servos. The top hole of the crank wants to be in line with the top of the flybar or just above. Secure the arms with the supplied servo screws. Secure your receiver to the servo housing with the sticky back hook and loop tape.

  • Page 19: Radio Setup

    RADIO SETUP Step 1: Please ensure the propeller has been removed before commencing the radio set up. Step 2: Set up a new model on your transmitter and bind your receiver. Step 3: Connect the ESC to the throttle channel, the lefthand servo (looking from behind the gondola) to CH6, and the righthand servo to CH5.
  • Page 20 This is the basic airframe finished, the fitting of the Parawing and the setting up of your computer radio is quite involved. To make life easier, we recommend you watch this video on YouTube in conjunction with the steps shown further on in this manual to achieve the best results for this part of the assembly and for setting the radio up.

  • Page 21: Attaching The Parawing

    ATTACHING THE PARAWING Measuring and tying a knot in the single riser control line. Step 1: Lay the parawing and the riser lines on your workbench and tape the end of the single, untied line (the one with a knot in it) of either the left, or right riser line to your bench. We recommend that you run the line alongside a steel ruler.
  • Page 22 Step 3: At the other end of the ruler, the Step 4: Remove the line from the workbench zero end, place a small piece of tape as and thread the taped end through the back shown on the zero mark. hoop (D ring) that is attached to the riser in the direction of the arrow.

  • Page 23: Safety Instructions

    SAFETY INSTRUCTIONS 1. Please read this manual carefully and follow the instructions before you use this product. 2. This Paramotor is not a toy, set up correctly it is suitable for novice pilots. However, if you are a complete novice it is best to try and enlist the assistance of an experienced pilot. 3.

  • Page 24: Flying The Paramotor V2

    FLYING THE PARAMOTOR V2 The H-King Paramotor V2 is straightforward and fun to fly, but some basic things make it slightly different from conventional fixed-wing airplanes. With the aid of a helper it can take off from the ground, but under normal circumstances, it is best to hand-launch it. The main difference to conventional airplanes is that there is no elevator as such, the up elevator control is really a brake for slowing the Paramotor down.
  • Page 25 Note: A flying video is available (link below), or click on the link under the video section of the listing for the H-King Paramotor V2 on the Hobbyking.com website. https://www.youtube.com/watch?v=E7BnNsdOiu0...

  • Page 26: Recommended Accessories

    RECOMMENDED ACCESSORIES Turnigy TGY-i6 Mode 2 AFHDS RADIOMASTER (Charcoal) Pocket ELRS Transmitter and 6CH Receiver FCC 2.4GHz Compact 16ch Transmitter w/Open-Source Edge TX Firmware SKU: 9114000020-0 SKU: 1022720065 OrangeRx Tx10i Mode 1 EU Version 10ch RADIOMASTER TX12 MKII CC2500 LBT 2.4GHz DSMX Compatible Radio System 2.4GHz Compact 12ch Transmitter w/ Open-Source Edge TX Firmware...
  • Page 27 Turnigy 5000mAh 3S 20C Lipo Turnigy Graphene Professional Pack w/XT-60 5200mAh 3S 15C LiPo Pack w/XT60 SKU: 9114000020-0 SKU: 9067000105-0 Turnigy Heavy Duty 5000mAh 3S Turnigy Rapid 6000mAh 3S (11.1V) 60C LiPo Pack w/XT-90 100C LiPo Battery Pack w/XT90 Connector SKU: 9067000236-0 SKU: 9067160568 Turnigy Graphene Panther...
  • Page 28 XT90 Male to XT60 Female Adapter HOTA H6 Pro AC/DC 200W AC/700W DC 2pcs 1~6S Smart Charger SKU: 258000140-0 SKU: 9466000020-3 Turnigy Reaktor D6 Pro Duo 2x325W HOTA P6 2 x 300W 1~6S Dual Smart (650W) Balance Charger AC/DC w/ Charger/Discharger (DC Only) Wireless Charging SKU: 9466000021-0...

  • Page 29: Spare Parts

    SPARE PARTS Propeller Guard Wheel Set SKU: 9310000405-0 SKU: 9310000406-0 Prop Guard Stays Main Frame SKU: 9310000407-0 SKU: 9310000408-0 Control Arms Main Landing Gear Set SKU: 9310790505 SKU: 9310790506 50A ESC w/Light Bar JST LED Light Bar Set Connector SKU: 9310790508 SKU: 9310790507...

Table of Contents

Save PDF