Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Infinite Manuals
  4. Extender
  5. L-com POEOD1GAT-EXT
  6. Owner's manual

Infinite L-com POEOD1GAT-EXT Owner's Manual

1-port gigabit poe+ water-resistant extender
Hide thumbs

Advertisement

Quick Links

Download this manual
Owner's Manual
1-Port Gigabit PoE+
Water-Resistant Extender
Model:
POEOD1GAT-EXT
1 1

Advertisement

loading
Need help?

Need help?

Do you have a question about the L-com POEOD1GAT-EXT and is the answer not in the manual?

Questions and answers

Related Manuals for Infinite L-com POEOD1GAT-EXT

Summary of Contents for Infinite L-com POEOD1GAT-EXT

  • Page 1 Owner’s Manual 1-Port Gigabit PoE+ Water-Resistant Extender Model: POEOD1GAT-EXT...

  • Page 2: Package Includes

    Package Includes • Gigabit PoE+ Extender POEOD1GAT-EXT • x2 Water-Resistant Covers • Owner’s Manual Product Features • Save time and money by extending data and power over existing network cables past the 100 m (328 ft.) limit • Extend a 10/100/1000 Mbps application over longer distances by cascading multiple extenders up to 500 m (1640 ft.) •...
  • Page 3 RJ45 Cable Wire and Crimp Steps 1. Strip an inch or so of the outer skin of a Cat5e/6 cable with a utility knife. Separate and straighten the internal wires, and arrange them in the proper order. Use a wire cutter to trim the wires evenly. Slide one of the included water-resistant covers along the end of the cable.
  • Page 4 RJ45 Cable Wire and Crimp Steps 3. Tighten the rear of the water-resistant cover until it fits snugly over the cable jacket and will not slide. 4. Connect the cable’s male RJ45 plug to the POEOD1GAT-EXT’s female RJ45 port.
  • Page 5 RJ45 Cable Wire and Crimp Steps 5. Screw the threaded coupling clockwise until tight. When installed correctly, the IP65-rated extender will be protected against dust and water spray from all directions.
  • Page 6 Single Extender Installation Note: Prior to connecting the RJ45 cable to input/output ports, install the included water-resistant dust caps onto the cable. Caps can be screwed onto the end of the port connection (see RJ45 Cable Wire and Crimp Steps for more information). 1.
  • Page 7 Multiple Extender Installation Note: You may only cascade up to four PoE extender units up to 500 m (1640 ft.) in a single installation. 1. Using a Cat5e/6 cable or better up to 100 m long, connect your powered source device (such as a PoE switch) into the “IN” port on the unit.
  • Page 8 Multiple Extender Installation Maximum Supported Power Multiple PoE Extenders can be connected every 100 m (328 ft.) for greater distances. The actual figures depend on operating conditions. The range is determined using 24 AWG or heavier Cat5e, Cat6 or better cable, unless otherwise specified.
  • Page 9 Multiple Extender Installation Examples for PoE+ devices (PoE Class 4 that requires less than 22 watts power, or 802.3at compliant): PoE Source PoE switch 15W midspan PoE+ switch 30W midspan (802.3af) (802.3af) (802.3at) (802.3at) Maximum Distances Not applicable Not applicable 200 m / 656 ft.

  • Page 10: Specifications

    Specifications IEEE Standards IEEE 802.3af (Power over Ethernet) IEEE 802.3at (High-Power PoE+ Power over Ethernet) IEEE 802.3 (10Base-T Ethernet) IEEE 802.3ab (Gigabit Ethernet) IEEE 802.3u (100Base-TX Fast Ethernet) IEEE 802.3x (Flow control, for full duplex mode) 100Base-TX Cat5 UTP/STP RJ45, 8 pin Media Support 1000Base-TX Cat5e/6 UTP/STP RJ45, 8 pin Ports...