Astro Pneumatic Tool ADR14 Quick Start Manual

MODEL:
WARNING
Study, understand and follow all instructions provided with
this product. Read these instructions carefully before
installing, operating, servicing or repairing this tool. Keep
these instructions in a safe accessible place.
INTENDED USE OF THE TOOL
WEAR WORK GLOVES (RUBBER COATED PREFERRED)
FOR GRIPPING THE ADAPTER. This tool is designed to be
used in drills chucks to set blind rivets up to 1/4" in aluminum,
steel and copper, and up to 7/32" in stainless steel. Do not
use this tool outside of the designed intent. Never modify the
tool for any other purpose or use.
WARNING
• Normal use of this product is likely to expose the user to
dust and/or microscopic particles containing chemicals
known to the State of California to cause cancer, birth
defects or other reproductive harm. Always wear
appropriate safety equipment and clothing when using
this product. Study, understand and follow all instructions
provided with this product. Failure to read and follow all
warnings and operating instructions may result in
damages and serious injury or death.
• Always wear ANSI approved goggles when using this
product. (Users and By standers).
• Never use this tool for any application other than for which
it was designed.
• Only use accessories designed for this tool.
• Never alter or modify this tool in any way.
• Improper operation and/or maintenance of the tool,
modification of the tool, or use of the tool with
accessories not designed for it could result in serious
injury or death.
• Always select the correct accessories of the correct size
and design for the job that you are attempting to perform.
• Always work in a clean, safe, well-lit, organized and
adequately equipped area.
• Do not begin repairs without assurance that vehicle is in
secure position, and will not move during repair.
XL BLIND RIVET ADAPTER KIT
- 1/4" CAPACITY
MADE IN CHINA
ADR14
PRODUCT TYPE:
XL BLIND RIVET ADAPTER KIT
- 1/4" CAPACITY
1 YEAR LIMITED WARRANTY
• Astro Pneumatic Tool Co. warrants our products to the original
user against defective material or workmanship for a period of 1
year (except where noted on our price schedule) from the date of
1st use. Astro reserves the right to determine whether the product
failed because of defective material, workmanship or other causes
and to charge back for missing parts. Astro Pneumatic Tool Co., at
its discretion, will repair products covered under this warranty free of
charge. The distributor should direct the original user to return the
product (with the exceptions listed below) with the distributor's
name, address, adequate proof of date of purchase or a copy of
warranty card, and a short note explaining the problem. Failures
caused by accident, alteration, or misuse are not covered by
this warranty.
• If one part of this product fails, please do not return the entire
product. Astro will replace free of charge component parts of
this product that fail within 1 year of first use by the original
user. Items included in this category include but are not
limited to kits, hand tool kits and any other product where there
are multiple items or components that make up the unit. Please
contact the phone number below in order to obtain the
replacement components covered under warranty.
• Astro Pneumatic Tool Co. or its authorized service representatives
must perform all warranty repairs. Any repair to the product by
unauthorized service representatives voids this warranty. The rights
under this warranty are limited to the original user and may not be
transferred to subsequent owners.
• This warranty is in lieu of all other warranties, expressed or
implied, including warranties of merchantability and fitness for a
particular purpose. Some states do not allow the exclusion of
limitations of incidental or consequential damages so the above
limitations may not apply to you.
PLEASE DO NOT RETURN ANY PRODUCT WITHOUT CALLING
1-800-221-9705 FOR INSTRUCTIONS
When unpacking, check the parts diagram and part
number listing on page 4 to make sure all parts are
included. If any parts are missing or damaged, please
call your distributor.
PRODUCT INFORMATION:
• Easily convert your cordless, pneumatic or corded
drill into a power pop riveter
• Includes nose pieces for 3/32", 1/8", 5/32", 3/16",
7/32" and 1/4" for steel, aluminum, copper or up
to 7/32" in stainless
• CNC machined from solid billet aluminum and
features Japanese bearings
DO NOT DISCARD – GIVE TO USER
Page 1
www.astrotools.com
Before Use