Page 1
Package Control iSteamX Control PUR100543 04-24 SteamHead 05-22 AromaSteam SteamHead PUR100421 (standard) Linear Steamhead PUR103936 05-22 (option) Accessories SteamLinx PUR100518 09-22 PUR10 0 -2 ChromaSteamX System PUR100580 0 -23 AromaSteam System PUR103938 Condensation Pan TS0012 AutoFlush PUR100200E MS / Super AutoFlush 05-22 (MS &...
Page 2
Installation, Operation & Maintenance Manual Installation, Operation and Maintenance Manual iSteamX Linear Steam Head Residential Model: 104480 ____________________ teri steam Feel Good Inc. ® steam ® ® Feel Good Inc. ®...
Page 3
® When installing and using this electrical equipment, basic safety precautions should always be followed, including the following: R E A D M E F I R S T ! IMPORTANT SAFETY INSTRUCTIONS As you follow these READ AND FOLLOW ALL INSTRUCTIONS instructions, you will notice warning and caution symbols.
® Table of Contents: Dimensional Information Important Safety Instructions ....1 iSteamX I N S T A L L E R I N F O R M A T I O N Installation Template .
Page 5
INSTALLER INFORMATION ® To avoid unintentional steambath Do not route iSteamX control wiring operation, do not locate the control where other inside conduit together with power lines or close to hot controls, accessories, shower heads, valves, body sprays water or steam piping. Doing so may result in an or similar within the shower could cause confusion or inoperative or hazardous installation.
Page 6
INSTALLER INFORMATION ® Locating the Control Determine the desired installation location of the control. The iSteamX controls are designed to be installed inside or outside the steam room as a matter of personal preference. If the control is installed inside the steam room: •...
Page 7
INSTALLER INFORMATION ® Installation Instructions for iSteamX STEP 1. Mount the hub securely. The hub may be mounted in any orientation. Plug the 30 foot generator cable into the generator and into the hub. Do not force or twist cable ends together. Forcing or twisting cable ends may damage the connectors.
Page 8
INSTALLER INFORMATION ® Installation Instructions for iSteamX (cont.) STEP 2 Peel the double stick adhesive off the back of the iSteamX control (2a). Apply a bead of silicone around the rear of the iSteamX control to create a moisture seal (2b). Carefully feed the cables into the rough-in box and secure the control to the wall.
® H O M E O W N E R S E C T I O N When installing and using this electrical equipment, basic safety precautions R E A D M E F I R S T ! should always be followed, including the following: As you follow these As you follow these instruc- IMPORTANT SAFETY INSTRUCTIONS...
Page 10
USER/HOMEOWNER INFORMATION ® Operating Instructions Set the steam bathing duration and temperature according to personal preference, however it is highly recommended to begin steam bathing at a low temperature setting to gauge comfort and safety levels. Set the duration at 10 minutes maximum to gauge comfort and safety levels.
Page 11
USER/HOMEOWNER INFORMATION ® Steam Settings Return to Main Screen Steam settings can also be adjusted by tapping Increase the Steam Settings icon on the main screen. From Temperature the steam setting screen select either Temperature or Duration. To adjust temperature use the + and – buttons.
Page 12
USER/HOMEOWNER INFORMATION ® Apps iSteamX must be connected to WiFi to use apps iSteamX must be paired with a Mr.Steam Audio@Home to hear audio from apps iSteamX includes a preinstalled selection of popular entertainment apps. Apps cannot be added or removed from iSteamX.
USER/HOMEOWNER INFORMATION ® System Settings Return to Main Screen Password Lock The password lock can help Tap to prevent unintentional use of the Connect to steambath. Please refer to the WiFi Tap to steam generator installation, Connect to Bluetooth operation and maintenance manual before using the Temperature Unit Selection...
Installation, Operation & Maintenance Manual ® SPAH2O START UP OPERATION For proper operation, a learning mode bust be initiated from the iSteamX prior to using SPAH2O. Ensure any unused shower valve outlets are capped prior to using the learning mode SPAH2O is compatible with iSteamX controls with software version 1.7.70 and higher.
Page 15
Installation, Operation & Maintenance Manual ® Once the shower leaning has been completed, each output can be assigned a fixture icon (note each may only be used once) Select the icon the corresponds to the output, once the selections are made press SAVE.
Page 16
Installation, Operation & Maintenance Manual ® OPERATION ON/OFF Output Selection Press the ON/OFF button to start and stop the shower. The shower value will always start output 1. Press the water droplet icon to navigate to the temperature/flow adjustment screen SPAH20 can have 2 outlets open at a time.
Page 17
Installation, Operation & Maintenance Manual ® OPERATION Tap Temperature to adjust the temperature of the shower. Use the + and – buttons to adjust the temperature. NOTE: The maximum allowable set point temperature is 118 *F. iSteamX will not allow a temperature to be set above what the valve is capable of based on water supply temperatures and fixtures flowrates.
USER/HOMEOWNER INFORMATION USER/HOMEOWNER INFORMATION ® ® Turning iSteamAXQ On and Off: • To power the iSteamAQX on, momentarily press the button on the bottom edge. • To power the iSteamAQX off, press and hold the button on the bottom edge of the control.
USER/HOMEOWNER INFORMATION ® FCC Statement: ISED Statement: Any Changes or modifications not expressly approved by This device contains licence-exempt the party responsible for compliance could void the user's transmitter(s)/receiver(s) that comply with Innovation, authority to operate the equipment. Science and Economic Development Canada’s licence- exempt RSS(s).
Digital 1, Express Steam, Feel Good Inc., From Bathroom to Spa, HomeWizard, iButler, iGenie, iSpa Package, iSteam, iTempo, iTempo/Plus, Linear Steamhead, Making Wellness a Way of Life, Music Therapy, My Steam, SmartSizing, Spa Package, Steam Genie, Steam on Demand, Steam in a Box, Steam@Home, SteamStart, SteamTherapy, MrSteam, Tala, Tala Bath & Body, Tempo, The Intelligent Steambath, Valet Package, and Virtual Spa System are registered trademarks of MrSteam.
Page 21
steam ® S T E A M H E A D ___________________________________________________________________________________________________________________________________________ I N S TA L L AT I O N I N S T R U C T I O N S 1/8" minimum clearance required when Acrylic Shield is used. See installation instructions IMPORTANT: See the Installation and Operation Manual Use Teflon...
Page 22
Installation, Operation and Maintenance Manual Linear Steam Head Residential Model: 104480 ____________________ teri IMPORTANT: Leave this material with the homeowner. steam ® Feel Good Inc. ®...
Page 23
Linear Steam Head ® ® Model 104480 T A B L E O F C O N T E N T S Important Safety Information ... .1-2 Installer Section: Box Contents ......3 Dimensional Information .
Page 24
Linear Steam Head ® ® Installer Section Model 104480 READ ME FIRST! This highlights information that is especially As you follow these instructions, you relevant to a problem free installation. will notice symbols. This information is important for the proper, safe and trouble free All information in these instructions is based on the latest installation of the Linear Steam Head.
Page 25
Linear Steam Head ® ® Installer Section Model 104480 accessories...etc.). If the installation and operation manuals are Steambath controls feature an integral or not available go to www.mrsteam.com for an online copy, or remote temperature sensor that senses room temperature. contact MrSteam Customer or Technical Services at 800-767- Install the linear steam head in a location where steam emission will not come in direct contact with the control or...
Page 26
Linear Steam Head ® ® Installer Section Model 104480 Bracket Adjustment Screws Adjustable Brackets P104481 - Linear Steam Head 104483 - Faceplate BOX CONTENTS: 104484 - Diverter • Linear Steam Head • AromaTray • Faceplate • Silicone Sealant 104482 - AromaTray •...
Page 27
Linear Steam Head ® ® Installer Section Model 104480 Steam Head Installation Linear SteamHead shown without the optional faceplate STEP 1. Confirm proper stud spacing: The studs or diverter. must have a minimum spacing of 14-1/8” and a maximum spacing 19". If the stud spacing is outside Copper Tubing the required range then shim or otherwise reposition or Brass Pipe...
Page 28
Linear Steam Head ® ® Installer Section Model 104480 Optional Faceplate Installation Thin Set The steam head is supplied with an optional faceplate. It is not required for the functional operation of the steam head. The faceplate is a decorative accessory and is Vapor Barrier Finished available in (8) finishes.
Page 29
Linear Steam Head ® ® Installer and Home Owner Section Model 104480 Steam Emission Zone The Steam Emission Zone is the area in front of the steam head that contains dense, hot steam as it exits the steam head. Steam dissipates as it moves away from the steam head, and becomes less hot. The steam zone is the area where contact with steam presentees a scalding hazard.
Page 30
Linear Steam Head ® ® Installer and Home Owner Section Model 104480 Diverter The Linear SteamHead is supplied with an optional steam diverter. The steam diverter is used to reduce the steam emission zone as required to avoid contact between a steam bather and direct steam emissions.
Page 31
Linear Steam Head ® ® Installer and Home Owner Section Model 104480 AromaTray The AromaTray is for use with MrSteam Essential Oils. Place a few drops of Rubber Portion Essential Oils in the AromaTray as shown to provide a fragrant steam bath for secure placement experience.
Page 32
Linear Steam Head ® ® Using MrSteam Essential Oils Model 104480 Enjoy Mr.Steam essential oils by placing a drop or two, into your Mr.Steam AromaTray as shown in the illustration. Only use Mr.Steam essential oils in a Mr.Steam AromaTray. Contact a MrSteam customer or technical Service representative for essential oil Manufacturer Safety Data Sheets ( MSDS ).
Installation, Operation & Maintenance Manual S A F ETY I N FO RM AT IO N This installation manual cointains essential information to make a full installation of the system. This manual includes a description of the system functions and capabilities, contingencies and alternate modes of operation, and step-by-step procedures Please read it carefully.
Installation, Operation & Maintenance Manual S TAN D AR DS & C E RT IF I C AT I O N S : H Y D RA UL I C PRESSURE BALANCE STANDARDS ASSE #1016 - Performance requirements for automatic compensating valves for individual showers and tub/shower combinations Including: 4.6.4 - Pressure and temperature variation test T type THERMOSTATIC STANDARDS Pr EN-1111 (2015) - Sanitary Tapware - Thermostatic Mixing Valves.
Installation, Operation & Maintenance Manual CO MP ON E N TS L I S T OUTLETS 180º INLETS Shower Valve 104328 27EV000007 CPU_iV2_3 Outlets Inlet Filter (x2) 104436 Control Cable 104548-30 Power Supply 104435 All drawing are for illustrative purposes only...
Installation, Operation & Maintenance Manual DIM EN S I O NS S h o w er Va l ve Pow e r S u p pl y K i t NEMA 1-15P 11 7/8” 6” 51 3/4” All drawing are for illustrative purposes only...
Installation, Operation & Maintenance Manual IN S TA L LAT I O N C O N SI D ER ATI O N S must be installed in an accessible location for Flush pipes thoroughly before and after installation. servicing and maintenance. Provide an access panel to allow future maintenance of the Not flushing the water supply pipe or not installing filters may cause damage to the valves by debris, which will cause...
Installation, Operation & Maintenance Manual T Y PI CA L I N STA L L ATI O N All drawings are for illustrative purposes only iSteamX and Steam Generator are NOT included with SPAH2O...
Installation, Operation & Maintenance Manual IN S TALL ATI ON G U ID E L I N ES The installation technician must follow the installation guidelines, respecting the areas and making sure about the equipotential union of the device. Rotate the mounting feet to the deployed position and attach the valve to the wall using the appropriate screws.
Page 46
Installation, Operation & Maintenance Manual IN S TALL ATI ON G U ID E L I N ES To iSteamX Hub Plug the communication cable into the connector labeled Plug the power supply into the connector labeled Conn. 3 Conn. 1 Control on the valve 12 VDC Plug the communication cable from the vale in the connector labeled SHOWER on the iSteamX Hub.
Page 47
Installation, Operation & Maintenance Manual I N S TA L LAT I O N G U I D EL I N ES Power Suppy Mark the position of the holes with a pencil. Make the holes in the wall with the appropriate measures. Mark the position of the holes with a pencil.
Installation, Operation & Maintenance Manual S TA RT U P OPE RAT I O N Shower Learning From the start screen, navigate to the features menu by pressing the features icon Navigate to Shower Setup in features menu and press Shower Learning. The hot and cold supply must be on and the shower fixtures MUST be connected.
Installation, Operation & Maintenance Manual Once the shower leaning has been completed, each output can be assigned a fixture icon (note each may only be used once) Select the icon the corresponds to the output, once the selections are made press SAVE. Note: If an output is not plumbed you will not be able to make a selection for it O PERAT I All drawing are for illustrative purposes only...
Page 50
Installation, Operation & Maintenance Manual OPE R AT I O N ON/OFF Output Selection Press the ON/OFF button to start and stop the shower. The shower value will always start output 1. Press the water droplet icon to navigate to the temperature/flow adjustment screen SPAH20 can have 2 outlets open at a time.
Installation, Operation & Maintenance Manual OPE R AT I ON Tap Temperature to adjust the temperature of the shower. Use the + and – buttons to adjust the temperature. The maximum allowable set point temperature is 118 *F. iSteamX will not allow a temperature to be set above what the valve is capable of based on water supply temperatures and fixtures flowrates.
Installation, Operation & Maintenance Manual REF. TYPE OF ALARM DESCRIPTION RECOMMENDED ACTION AL 1 Cold water Device on standby mode detects cold water leakage Run the automatic clean-up program. lf leakage This means that the cold water valve is not properly the problem persists replace the device.
Page 54
Installation, Operation and Maintenance Manual Installation, Operation, and Maintenance Manual Audio@Home ® Audio@Steam ® 240 Volt steam ® Feel Good Inc. ®...
Page 55
IMPORTANT SAFETY INFORMATION READ ME FIRST: 1. Read and follow all instructions within this technical manual. 2. Heed all warnings, cautions, notices, and important notes. 3. Save this technical manual and leave with the homeowner. ABOUT WARNINGS, CAUTIONS, NOTICES, AND IMPORTANT NOTES: As you follow the instructions in this technical manual, you will see four types of callouts: WARNINGS, CAUTIONS, NOTICES, IMPORTANT NOTES...
Page 56
IMPORTANT SAFETY INFORMATION Before installing or connecting the Audio@Home, please read the following: • To prevent a shock hazard, do not disassemble or alter the Audio@Home. • To prevent over temperature shutoff and equipment damage, do not use foam to insulate the Audio@Home.
Page 57
steam ® ® Audio@Home T A B L E O F C O N T E N T S INSTALLER INSTRUCTIONS 1. General information ......5 Box Contents .
mr . steam ® ® Audio@Home 1. General Information Box Contents Audio@Home General Installation Figure 2 shows how to use the Audio@Home standalone system within your steam room (i.e., if your steam room does not use iSteam3). Audio@Home Speaker wire (100 ft max) Speakers Audio@Home Grounded wall outlet...
steam ® ® ® Audio@Home 2. Installing Audio@Home Audio@Home Dimensions Figure 3 shows the face-on dimensions of Audio@Home. Figure 4 shows the side-view dimensions of Audio@Home. Shock hazard. Do not place the control box in a location where it can get wet. Locating and Installing Audio@Home To prevent water from getting inside the device, Audio@Home should be mounted on two stable vertical surfaces (e.g., studs) as shown in Figure 5.
steam ® ® Audio@Home ® 3. Connecting Audio@Home (Audio@Home does not connect to the steam Generator) • To reduce the risk of electric shock, do not remove the screws on the back of Audio@Home. No user serviceable parts inside. Refer servicing to qualified service personnel. •...
steam ® ® ® Audio@Home Connecting Speakers 1. Connect individual speaker wires — or a 10-pin MATE-N-LOK adapter with attached wires — to the speaker outputs. Refer to Figure 10 and Figure 11 for connector identification. IMPORTANT NOTES • If you use individual speaker wires, the recommended socket crimping contact is an AWG 14-20 (TE Connectivity part number 350550-3).
steam ® ® ® Audio@Home Pairing a Bluetooth-Enabled Device To pair a Bluetooth-enabled device to Audio@Home: 1. Ensure that the mobile device is in range of Audio@Home, and that it is powered on and Bluetooth is turned on. 2. Open the Bluetooth settings on your device. 3.
steam ® ® ® Audio@Home 5. Regulatory Statements FCC Compliance Statement Contains Transmitter Module FCC ID: A8TBM23SPKXYC2A This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
mr . steam ® Audio@Home ® 6. About Audio@Home Audio@Home offers you the perfect means to bring music into your steam room. Audio@Home is compatible with bluetooth devices. Audio@Home can connect to two speakers. IMPORTANT NOTES • If a Bluetooth-connected device moves out of range and loses connection with Audio@Home, it should reconnect auto-matically with Audio@Home (without having to go through the pairing process again) when moved within range.
Page 69
Installation, Operation and Maintenance Manual Installation, Operation, and Maintenance Manual ChromaSteam ® Residential Model: ____________________ teri steam ® Feel Good Inc. ® steam Feel Good Inc. ® ®...
Page 70
® INSTALLATION, OPERATION, & MAINTENANCE ChromaSteam ® IMPORTANT SAFETY INFORMATION READ ME FIRST: 1. Read and follow all instructions within this technical manual. 2. Heed all warnings, cautions, notices, and important notes. 3. Save this technical manual and leave with the homeowner. ABOUT WARNINGS, CAUTIONS, NOTICES, AND IMPORTANT NOTES: WARNINGS, CAUTIONS, As you follow the instructions in this technical manual, you will see four types of callouts:...
Page 71
TABLE OF CONTENTS: INSTALLER INSTRUCTIONS General Information Box Contents ..........3 General Installation .
® INSTALLATION, OPERATION, & MAINTENANCE ChromaSteam ® INSTALLER INSTRUCTIONS General Information ChromaSteamX Box Contents: ChromaSteamX Led Power Control Tube of Accessory Junction Box Fixture (30 Ft) Cable Communication Silicone Cable (30Ft) Power Suppy ChromaSteamX Duo Box Contents: (2) ChromaSteamX (2) Led Power Control (2) Tube of Accessory...
® INSTALLATION, OPERATION, & MAINTENANCE ChromaSteam ® General Installation Figure 3 shows how the ChromaSteamX fixture and control box interconnect with each other, and with the steam generator and iSteamX. IMPORTANT NOTES: • The included ChromaSteamX accessory communication cable and LED power cable are each 30 ft long. Ensure that the ChromaSteamX fixture and control box are located accordingly.
® INSTALLATION, OPERATION, & MAINTENANCE ChromaSteam ® Installing the ChromaSteamX Control Box Control Box Dimensions • To prevent product or property damage, do not expose control box to temperatures above 140 °F (60 °C). Do not locate control box in an attic or any location where ambient temperatures may...
® INSTALLATION, OPERATION, & MAINTENANCE ChromaSteam ® Installing the ChromaSteamX Fixture Fixture Dimensions Figure 5 Figure 6 ” P O R T I O N [38mm] I N C E I L I N G P O R T I O N ”...
® INSTALLATION, OPERATION, & MAINTENANCE ChromaSteam ® Installing the Junction Box Functions of the Junction Box: 1. Allows precisely location of the ChromaSteamX fixture within • Installation to be performed by a the steam room ceiling. qualified and licensed electrician. 2.
Page 77
® INSTALLATION, OPERATION, & MAINTENANCE ChromaSteam ® Ceiling joist Knockouts Junction box tabs Figure 7 Figure 8 End of 30-foot LED power cable End of 30-foot control cable or one of the longer ends of Duo cable Figure 9 Figure 10 All drawings are for illustrative purposes only.
® INSTALLATION, OPERATION, & MAINTENANCE ChromaSteam ® Installing the Fixture To Install the Fixture: 1. Connect the ChromaSteamX fixture’s pigtail to the 30-foot LED power cable in the junction box (Figure 11). IMPORTANT NOTE: Test that the fixture operates correctly prior to continuing with the following steps. 2.
Page 79
® INSTALLATION, OPERATION, & MAINTENANCE INSTALLATION, OPERATION, & MAINTENANCE ChromaSteam ChromaSteam ® ® Connecting the ChromaSteamX Fixture to the ChromaSteamX Control Box • Shock Hazard. Ensure that power is turned off during installation. Turn off power at breaker panel. • Shock Hazard. To prevent electric shock, do not remove the screws on the back of the control box.
® INSTALLATION, OPERATION, & MAINTENANCE ChromaSteam ® Connecting the ChromaSteamX Control Box to iSteamX Hub 1. Plug the accessory communication cable into the port labeled Hub on the LED controller. (Figure 16) 2. Plug the FREE END of the accessory communication cable into any of the accessory ports on the iSteam Hub.
® INSTALLATION, OPERATION, & MAINTENANCE ChromaSteam ® Connecting the ChromaSteamX to Power Before specs, nish up installation 1. Plug in the power supply provided with ChromaSteamX (Figure 18) into the ChromaSteamX control box port marked 12 VDC. 2. Plug the power supply into a standard outlet. Connecting Control Box to Power Figure 18...
® INSTALLATION, OPERATION, & MAINTENANCE ChromaSteam ® HOMEOWNRE/END-USER INSTRUCTIONS About ChromaSteamX Like water and heat, light is a fundamental life force and may improve your physical and mental state. The Mr.Steam ChromaSteam X system integrates light with steam, creating chromatherapy environments rich with ®...
® INSTALLATION, OPERATION, & MAINTENANCE ChromaSteam ® Operating ChromaSteamX You can control the ChromaSteamX LED module from within your Note that ChromaSteamX is for mood steam room using the iSteamX control. Select from 78,000 lighting only, and does not substitute different colors —...
Page 85
Residential and Day Spa Steam Rooms Part Number MS AROMA ( __________________________________ ____________________ IMPORTANT: Leave this material with the home owner. __________________________________ Leave this material with the homeowner. IMPORTANT: ____________________ steam Feel Good Inc. ® steam ® ® Feel Good Inc. ®...
Page 86
AromaSteam ® Operation and Installation Instructions I N S T A L L E R S E C T I O N BEFORE INSTALLING T A B L E O F C O N T E N T S Carefully inspect the AromaSteam and packaging for shipping damage.
Page 87
IMPORTANT: Leave this material with the homeowner. teri steam ® Feel Good Inc. ® This installation, operation and maintenance manual is for general reference. The installation, operation and maintenance manual supplied with the product must be used for installation, operation and maintenance purposes. Failure to use the installation, operation and maintenance manual supplied may result in a property damage or personal injury.
Page 88
AromaSteam ® Operation and Installation Instructions I N S T A L L E R S E C T I O N IMPORTANT NOTE: As you follow these instructions, you will notice warning and caution symbols. This blocked information is important for the safe and efficient installation and use of fragrance and AromaSteam. These are types of potential hazards that may occur during installation and operation: Signals a Hazard that may cause serious injury or death if precautions are not followed.
Page 89
AromaSteam ® Operation and Installation Instructions I N S T A L L E R S E C T I O N 1. Keep the AromaSteam away from heat, sparks, elec trical outlets, open flames such as candles and hot surfaces. 2.
Page 90
AromaSteam ® Operation and Installation Instructions I N S T A L L E R S E C T I O N AromaSteam Overview Receptacle required AromaSteam Pump Steam Generator Printed Circuit Board AromaSteam Transformer 120VAC/240VAC Pressure Hose Request Cable Check Valve Steam...
Page 91
AromaSteam ® Operation and Installation Instructions I N S T A L L E R S E C T I O N General System Dimensions ® AROMASTEAM Suction Hose Pressure Hose 6ft. Fragrance Container Request Cable 6ft. AromaSteam Transformer (To Steam Generator) 120VAC/240VAC ft (To Outlet) Check Valve...
Page 92
AromaSteam ® Operation and Installation Instructions I N S T A L L E R S E C T I O N Installing the AromaSteam Tools required: • Cordless drill with a Phillips bit • Level Use only non-sparking tools. Take pre cautionary measures Back of Pump against static discharge "...
Page 93
AromaSteam ® Operation and Installation Instructions I N S T A L L E R S E C T I O N Drill Template IMPORTANT NOTE: Do no scale template. Template must be printed at 1:1 scale. WARNING: Failure to print template at 1:1 scale will result in wrong mounting hole locations.
Page 94
AromaSteam ® Operation and Installation Instructions I N S T A L L E R S E C T I O N Installing the 90 degree T For optimal results locate a brass 90 degree T (not provid ed) in the steam supply line within 5-10 feet of the steam head.
Page 95
AromaSteam ® Operation and Installation Instructions I N S T A L L E R S E C T I O N Installation of the fragrance container 1. Locate the container cap with the hole that is included with the bottle of fragrance. Replace the fragrance container cap with the cap with the hole.
Page 96
AromaSteam ® Operation and Installation Instructions I N S T A L L E R S E C T I O N Electrical Connection of AromaSteam IMPORTANT NOTE: AromaSteam is for use with AirTempo iSteam and iTempoPlus con trols only. ®...
Page 97
AromaSteam ® Operation and Installation Instructions I N S T A L L E R S E C T I O N Priming the AromaSteam 1. Ensure MrSteam fragrance container is full 2. Press and hold the priming button until liquid fills the suction hose all the way to pump head in AromaSteam.
Page 98
AromaSteam ® Operation and Installation Instructions I N S T A L L E R S E C T I O N Adjusting the Amount of Fragrance Delivery The AromaSteam has been factory set to deliver a suitable amount of aromatic fragrance into a typical sized steam room.
Page 99
AromaSteam ® Operation and Installation Instructions I N S T A L L E R S E C T I O N Troubleshooting TO AVOID ELECTRIC SHOCK, DISCONNECT POWER TO AROMASTEAM BEFORE SERVICING AromaSteam does not prime 1. Check if correct voltage is available. 2.
Page 100
AromaSteam ® Operation and Installation Instructions I N S T A L L E R S E C T I O N Replacement Parts This AromaSteam is factory wired. If the power cord of the AromaSteam is damaged it must be replaced by the MrSteam service department or similarly qualified personnel in order to avoid an electric shock hazard.
Page 101
AromaSteam Operation and Installation Instructions ® H O M E O W N E R S E C T I O N The AromaSteam’s state-of-the-art AromaSteam introduces fragrance into the steam pipe and into your steam shower. MrSteam Aroma is Available in These Five Fragrances: FRAGRANCE PART NO.
Page 102
AromaSteam ® Operation and Installation Instructions H O M E O W N E R S E C T I O N IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS FLAMMABLE LIQUID AND VAPOR • Keep away from heat, sparks, open flames, & hot surfaces protection or face protection •...
Page 103
AromaSteam ® Operation and Installation Instructions H O M E O W N E R S E C T I O N Locating the AromaSteam/Fragrance: 1. Place in a location that allows visual monitoring of the fragrances level. 2. The AromaSteam should not be installed in areas accessible to children. A locked room is strongly recommended (ie: utility room).
Page 104
® Feel Good Inc. ® www.mrsteam.com Products, information and specifications are subject to change without notice. For more information call Sales & Support at 1.800.767.8326 (East Coast) or 1.800.727.8326 (West Coast) for more information.
Page 105
steam ® Technical Specifications Condensation Pan 103867 & 104402 Mr.Steam strongly recommends the use of a condensation pan in the unlikely event of a plumbing leak. Locate the condensation pan on a solid level surface and place the steam generator inside the condensation pan. Insure the steam generator is level.
Page 106
mr . steam ® ® Optional AutoFlush System ____________________________________________________________________________________________________________________________________________ INSTALLATION INSTRUCTIONS BOX CONTENTS: • AutoFlush System Valve with Cord • Installation Instructions. ® ASSEMBLY OF OPTIONAL AUTOFLUSH SYSTEM 3 Pin Connector for AutoFlush AutoFlush Cord Connector AutoFlush Cord Steam Generator AutoFlush Valve End "B"...
Page 107
AutoFlush Shown Fully Assembled INSTALLATION INSTRUCTIONS ® 1. Plumbing to be performed by a qualified plumber and shall be in accordance with applicable National and Local codes. Unit drains by gravity. A drain line that is lower than the AutoFlush assembly must be available.
Page 108
mr . steam ® Optional AutoFlush ® System ____________________________________________________________________________________________________________________________________________ INSTALLATION INSTRUCTIONS BOX CONTENTS: • AutoFlush System Valve with Cord • Installation Instructions. ® ASSEMBLY OF OPTIONAL AUTOFLUSH SYSTEM 3 Pin Connector for AutoFlush AutoFlush Cord Connector AutoFlush Cord Steam Generator AutoFlush Valve Drain Valve Nipple...
Page 109
AutoFlush Shown Fully Assembled INSTALLATION INSTRUCTIONS ® 1. Plumbing to be performed by a qualified plumber and shall be in accordance with applicable national and local codes. Unit drains by gravity. A drain line that is lower than the AutoFlush assembly must be available.
Page 110
Installation, Operation & Maintenance Manual Installation, Operation and Maintenance Manual Residential Model: ____________________ teri steam Feel Good Inc. ® steam ® ® Feel Good Inc. ®...
Page 111
® When installing and using this electrical equipment, basic safety precautions should always be followed, including the following: R E A D M E F I R S T ! IMPORTANT SAFETY INSTRUCTIONS As you follow these READ AND FOLLOW ALL INSTRUCTIONS instructions, you will notice warning and caution symbols.
Page 112
® Table of Contents: Dimensional Information Important Safety Instructions ....1 iSteamX I N S T A L L E R I N F O R M A T I O N Box Content .
Page 113
INSTALLER INFORMATION ® To avoid unintentional steambath Do not route iSteamX control wiring operation, do not locate the control where other inside conduit together with power lines or close to hot controls, accessories, shower heads, valves, body sprays water or steam piping. Doing so may result in an or similar within the shower could cause confusion or inoperative or hazardous installation.
Page 114
INSTALLER INFORMATION ® Locating the Control Determine the desired installation location of the control. The iSteamX controls are designed to be installed inside or outside the steam room as a matter of personal preference. If the control is installed inside the steam room: •...
Page 115
INSTALLER INFORMATION ® Installation Instructions for iSteamX STEP 1. Mount the hub securely. The hub may be mounted in any orientation. Plug the 30 foot generator cable into the generator and into the hub. Do not force or twist cable ends together. Forcing or twisting cable ends may damage the connectors.
Page 116
INSTALLER INFORMATION ® Installation Instructions for iSteamX (cont.) STEP 2 Peel the double stick adhesive off the back of the iSteamX control (2a). Apply a bead of silicone around the rear of the iSteamX control to create a moisture seal (2b). Carefully feed the cables into the rough-in box and secure the control to the wall.
® H O M E O W N E R S E C T I O N When installing and using this electrical equipment, basic safety precautions R E A D M E F I R S T ! should always be followed, including the following: As you follow these As you follow these instruc- IMPORTANT SAFETY INSTRUCTIONS...
USER/HOMEOWNER INFORMATION ® Operating Instructions Set the steam bathing duration and temperature according to personal preference, however it is highly recommended to begin steam bathing at a low temperature setting to gauge comfort and safety levels. Set the duration at 10 minutes maximum to gauge comfort and safety levels.
USER/HOMEOWNER INFORMATION ® Steam Settings Return to Main Screen Steam settings can also be adjusted by tapping Increase the Steam Settings icon on the main screen. From Temperature the steam setting screen select either Temperature or Duration. To adjust temperature use the + and – buttons.
USER/HOMEOWNER INFORMATION ® Apps iSteamX must be connected to WiFi to use apps iSteamX must be paired with a Mr.Steam Audio@Home to hear audio from apps iSteamX includes a preinstalled selection of popular entertainment apps. Apps cannot be added or removed from iSteamX.
Page 121
USER/HOMEOWNER INFORMATION ® System Settings Return to Main Screen Password Lock The password lock can help Tap to prevent unintentional use of the Connect to steambath. Please refer to the WiFi Tap to steam generator installation, Connect to Bluetooth operation and maintenance manual before using the Temperature Unit Selection...
USER/HOMEOWNER INFORMATION ® Turning iSteam On and Off: • To power the iSteam on, momentarily press the button on the bottom edge. • To power the iSteam off, press and hold the button on the bottom edge of the control. Follow the onscreen prompts for power the iSteam off Care Tips Use only mild soap and water on a soft cloth to clean the control.
Page 123
USER/HOMEOWNER INFORMATION ® FCC Statement: ISED Statement: Any Changes or modifications not expressly approved by This device contains licence-exempt the party responsible for compliance could void the user's transmitter(s)/receiver(s) that comply with Innovation, authority to operate the equipment. Science and Economic Development Canada’s licence- exempt RSS(s).
Page 125
steam ® S T E A M H E A D ___________________________________________________________________________________________________________________________________________ I N S TA L L AT I O N I N S T R U C T I O N S 1/8" minimum clearance required when Acrylic Shield is used. See installation instructions IMPORTANT: See the Installation and Operation Manual Use Teflon...
Page 126
Installation, Operation and Maintenance Manual Linear Steam Head Residential Model: 104480 ____________________ teri IMPORTANT: Leave this material with the homeowner. steam ® Feel Good Inc. ®...
Page 127
Linear Steam Head ® ® Model 104480 T A B L E O F C O N T E N T S Important Safety Information ... .1-2 Installer Section: Box Contents ......3 Dimensional Information .
Linear Steam Head ® ® Installer Section Model 104480 READ ME FIRST! This highlights information that is especially As you follow these instructions, you relevant to a problem free installation. will notice symbols. This information is important for the proper, safe and trouble free All information in these instructions is based on the latest installation of the Linear Steam Head.
Page 129
Linear Steam Head ® ® Installer Section Model 104480 accessories...etc.). If the installation and operation manuals are Steambath controls feature an integral or not available go to www.mrsteam.com for an online copy, or remote temperature sensor that senses room temperature. contact MrSteam Customer or Technical Services at 800-767- Install the linear steam head in a location where steam emission will not come in direct contact with the control or...
Linear Steam Head ® ® Installer Section Model 104480 Bracket Adjustment Screws Adjustable Brackets P104481 - Linear Steam Head 104483 - Faceplate BOX CONTENTS: 104484 - Diverter • Linear Steam Head • AromaTray • Faceplate • Silicone Sealant 104482 - AromaTray •...
Page 131
Linear Steam Head ® ® Installer Section Model 104480 Steam Head Installation Linear SteamHead shown without the optional faceplate STEP 1. Confirm proper stud spacing: The studs or diverter. must have a minimum spacing of 14-1/8” and a maximum spacing 19". If the stud spacing is outside Copper Tubing the required range then shim or otherwise reposition or Brass Pipe...
Linear Steam Head ® ® Installer Section Model 104480 Optional Faceplate Installation Thin Set The steam head is supplied with an optional faceplate. It is not required for the functional operation of the steam head. The faceplate is a decorative accessory and is Vapor Barrier Finished available in (8) finishes.
Linear Steam Head ® ® Installer and Home Owner Section Model 104480 Steam Emission Zone The Steam Emission Zone is the area in front of the steam head that contains dense, hot steam as it exits the steam head. Steam dissipates as it moves away from the steam head, and becomes less hot. The steam zone is the area where contact with steam presentees a scalding hazard.
Linear Steam Head ® ® Installer and Home Owner Section Model 104480 Diverter The Linear SteamHead is supplied with an optional steam diverter. The steam diverter is used to reduce the steam emission zone as required to avoid contact between a steam bather and direct steam emissions.
Linear Steam Head ® ® Installer and Home Owner Section Model 104480 AromaTray The AromaTray is for use with MrSteam Essential Oils. Place a few drops of Rubber Portion Essential Oils in the AromaTray as shown to provide a fragrant steam bath for secure placement experience.
Page 136
Linear Steam Head ® ® Using MrSteam Essential Oils Model 104480 Enjoy Mr.Steam essential oils by placing a drop or two, into your Mr.Steam AromaTray as shown in the illustration. Only use Mr.Steam essential oils in a Mr.Steam AromaTray. Contact a MrSteam customer or technical Service representative for essential oil Manufacturer Safety Data Sheets ( MSDS ).
Page 138
Generator Cover Knock-out in the Generator Circuit Jacket Board Cover Screws...
Page 139
Home Router Power Supply 3’ Cable Ethernet Cable (3’) PUR 100518...
Page 140
AudioX INSTALLATION INSTRUCTIONS Model Audio XBK & Audio XWH PACKAGE CONTENTS: 1x AudioX [pair of speakers] 1x Installation Instructions 2x Templates 1x power cable 1x audio cable SPEAKER RATINGS: 60 watt peak/25 watt RMS/8 ohm impedance/5” depth Operating Temperature 0 °C – 60 °C (32 °F – 140 °F) SUPPLY RATING: Bracket 100-240 VAC, 50/60 Hz, 1.0 A max.
Page 141
AudioX INSTALLATION INSTRUCTIONS Model Audio XBK & Audio XWH WIRING DIAGRAM ADAPTER 21V/3A 3 in (88mm) 15 ft (4572mm) 7.5 in (200mm) 7.5 in (200mm) Active Ceiling Speaker Passive Ceiling Speaker...
Page 142
AudioX INSTALLATION INSTRUCTIONS Model Audio XBK & Audio XWH (167 mm) (167 mm) WARRANTY: To view or download the MrSteam Controls & Accessories Warranty and register your product go to: blog.mrsteam.com/wr...
Page 143
AudioX INSTALLATION INSTRUCTIONS Model Audio XBK & Audio XWH (167 mm) (167 mm) WARRANTY: To view or download the MrSteam Controls & Accessories Warranty and register your product go to: blog.mrsteam.com/wr...
Page 145
Installation, Operation and Maintenance Manual Installation, Operation, and Maintenance Manual ChromaSteam ® Residential Model: ____________________ teri steam ® Feel Good Inc. ® steam Feel Good Inc. ® ®...
Page 146
® INSTALLATION, OPERATION, & MAINTENANCE ChromaSteam ® IMPORTANT SAFETY INFORMATION READ ME FIRST: 1. Read and follow all instructions within this technical manual. 2. Heed all warnings, cautions, notices, and important notes. 3. Save this technical manual and leave with the homeowner. ABOUT WARNINGS, CAUTIONS, NOTICES, AND IMPORTANT NOTES: WARNINGS, CAUTIONS, As you follow the instructions in this technical manual, you will see four types of callouts:...
Page 147
TABLE OF CONTENTS: INSTALLER INSTRUCTIONS General Information Box Contents ..........3 General Installation .
® INSTALLATION, OPERATION, & MAINTENANCE ChromaSteam ® INSTALLER INSTRUCTIONS General Information ChromaSteamX Box Contents: ChromaSteamX Led Power Control Tube of Accessory Junction Box Fixture (30 Ft) Cable Communication Silicone Cable (30Ft) Power Suppy ChromaSteamX Duo Box Contents: (2) ChromaSteamX (2) Led Power Control (2) Tube of Accessory...
® INSTALLATION, OPERATION, & MAINTENANCE ChromaSteam ® General Installation Figure 3 shows how the ChromaSteamX fixture and control box interconnect with each other, and with the steam generator and iSteamX. IMPORTANT NOTES: • The included ChromaSteamX accessory communication cable and LED power cable are each 30 ft long. Ensure that the ChromaSteamX fixture and control box are located accordingly.
® INSTALLATION, OPERATION, & MAINTENANCE ChromaSteam ® Installing the ChromaSteamX Control Box Control Box Dimensions • To prevent product or property damage, do not expose control box to temperatures above 140 °F (60 °C). Do not locate control box in an attic or any location where ambient temperatures may...
® INSTALLATION, OPERATION, & MAINTENANCE ChromaSteam ® Installing the ChromaSteamX Fixture Fixture Dimensions Figure 5 Figure 6 ” P O R T I O N [38mm] I N C E I L I N G P O R T I O N ”...
® INSTALLATION, OPERATION, & MAINTENANCE ChromaSteam ® Installing the Junction Box Functions of the Junction Box: 1. Allows precisely location of the ChromaSteamX fixture within • Installation to be performed by a the steam room ceiling. qualified and licensed electrician. 2.
Page 153
® INSTALLATION, OPERATION, & MAINTENANCE ChromaSteam ® Ceiling joist Knockouts Junction box tabs Figure 7 Figure 8 End of 30-foot LED power cable End of 30-foot control cable or one of the longer ends of Duo cable Figure 9 Figure 10 All drawings are for illustrative purposes only.
® INSTALLATION, OPERATION, & MAINTENANCE ChromaSteam ® Installing the Fixture To Install the Fixture: 1. Connect the ChromaSteamX fixture’s pigtail to the 30-foot LED power cable in the junction box (Figure 11). IMPORTANT NOTE: Test that the fixture operates correctly prior to continuing with the following steps. 2.
Page 155
® INSTALLATION, OPERATION, & MAINTENANCE INSTALLATION, OPERATION, & MAINTENANCE ChromaSteam ChromaSteam ® ® Connecting the ChromaSteamX Fixture to the ChromaSteamX Control Box • Shock Hazard. Ensure that power is turned off during installation. Turn off power at breaker panel. • Shock Hazard. To prevent electric shock, do not remove the screws on the back of the control box.
® INSTALLATION, OPERATION, & MAINTENANCE ChromaSteam ® Connecting the ChromaSteamX Control Box to iSteamX Hub 1. Plug the accessory communication cable into the port labeled Hub on the LED controller. (Figure 16) 2. Plug the FREE END of the accessory communication cable into any of the accessory ports on the iSteam Hub.
® INSTALLATION, OPERATION, & MAINTENANCE ChromaSteam ® Connecting the ChromaSteamX to Power Before specs, nish up installation 1. Plug in the power supply provided with ChromaSteamX (Figure 18) into the ChromaSteamX control box port marked 12 VDC. 2. Plug the power supply into a standard outlet. Connecting Control Box to Power Figure 18...
Page 158
® INSTALLATION, OPERATION, & MAINTENANCE ChromaSteam ® HOMEOWNRE/END-USER INSTRUCTIONS About ChromaSteamX Like water and heat, light is a fundamental life force and may improve your physical and mental state. The Mr.Steam ChromaSteam X system integrates light with steam, creating chromatherapy environments rich with ®...
® INSTALLATION, OPERATION, & MAINTENANCE ChromaSteam ® Operating ChromaSteamX You can control the ChromaSteamX LED module from within your Note that ChromaSteamX is for mood steam room using the iSteamX control. Select from 78,000 lighting only, and does not substitute different colors —...
Page 161
Residential and Day Spa Steam Rooms Part Number MS AROMA ( __________________________________ ____________________ IMPORTANT: Leave this material with the home owner. __________________________________ Leave this material with the homeowner. IMPORTANT: ____________________ steam Feel Good Inc. ® steam ® ® Feel Good Inc. ®...
Page 162
AromaSteam ® Operation and Installation Instructions I N S T A L L E R S E C T I O N BEFORE INSTALLING T A B L E O F C O N T E N T S Carefully inspect the AromaSteam and packaging for shipping damage.
Page 163
IMPORTANT: Leave this material with the homeowner. teri steam ® Feel Good Inc. ® This installation, operation and maintenance manual is for general reference. The installation, operation and maintenance manual supplied with the product must be used for installation, operation and maintenance purposes. Failure to use the installation, operation and maintenance manual supplied may result in a property damage or personal injury.
Page 164
AromaSteam ® Operation and Installation Instructions I N S T A L L E R S E C T I O N IMPORTANT NOTE: As you follow these instructions, you will notice warning and caution symbols. This blocked information is important for the safe and efficient installation and use of fragrance and AromaSteam. These are types of potential hazards that may occur during installation and operation: Signals a Hazard that may cause serious injury or death if precautions are not followed.
AromaSteam ® Operation and Installation Instructions I N S T A L L E R S E C T I O N 1. Keep the AromaSteam away from heat, sparks, elec trical outlets, open flames such as candles and hot surfaces. 2.
AromaSteam ® Operation and Installation Instructions I N S T A L L E R S E C T I O N AromaSteam Overview Receptacle required AromaSteam Pump Steam Generator Printed Circuit Board AromaSteam Transformer 120VAC/240VAC Pressure Hose Request Cable Check Valve Steam...
AromaSteam ® Operation and Installation Instructions I N S T A L L E R S E C T I O N General System Dimensions ® AROMASTEAM Suction Hose Pressure Hose 6ft. Fragrance Container Request Cable 6ft. AromaSteam Transformer (To Steam Generator) 120VAC/240VAC ft (To Outlet) Check Valve...
Page 168
AromaSteam ® Operation and Installation Instructions I N S T A L L E R S E C T I O N Installing the AromaSteam Tools required: • Cordless drill with a Phillips bit • Level Use only non-sparking tools. Take pre cautionary measures Back of Pump against static discharge "...
Page 169
AromaSteam ® Operation and Installation Instructions I N S T A L L E R S E C T I O N Drill Template IMPORTANT NOTE: Do no scale template. Template must be printed at 1:1 scale. WARNING: Failure to print template at 1:1 scale will result in wrong mounting hole locations.
Page 170
AromaSteam ® Operation and Installation Instructions I N S T A L L E R S E C T I O N Installing the 90 degree T For optimal results locate a brass 90 degree T (not provid ed) in the steam supply line within 5-10 feet of the steam head.
Page 171
AromaSteam ® Operation and Installation Instructions I N S T A L L E R S E C T I O N Installation of the fragrance container 1. Locate the container cap with the hole that is included with the bottle of fragrance. Replace the fragrance container cap with the cap with the hole.
Page 172
AromaSteam ® Operation and Installation Instructions I N S T A L L E R S E C T I O N Electrical Connection of AromaSteam IMPORTANT NOTE: AromaSteam is for use with AirTempo iSteam and iTempoPlus con trols only. ®...
Page 173
AromaSteam ® Operation and Installation Instructions I N S T A L L E R S E C T I O N Priming the AromaSteam 1. Ensure MrSteam fragrance container is full 2. Press and hold the priming button until liquid fills the suction hose all the way to pump head in AromaSteam.
Page 174
AromaSteam ® Operation and Installation Instructions I N S T A L L E R S E C T I O N Adjusting the Amount of Fragrance Delivery The AromaSteam has been factory set to deliver a suitable amount of aromatic fragrance into a typical sized steam room.
AromaSteam ® Operation and Installation Instructions I N S T A L L E R S E C T I O N Troubleshooting TO AVOID ELECTRIC SHOCK, DISCONNECT POWER TO AROMASTEAM BEFORE SERVICING AromaSteam does not prime 1. Check if correct voltage is available. 2.
AromaSteam ® Operation and Installation Instructions I N S T A L L E R S E C T I O N Replacement Parts This AromaSteam is factory wired. If the power cord of the AromaSteam is damaged it must be replaced by the MrSteam service department or similarly qualified personnel in order to avoid an electric shock hazard.
AromaSteam Operation and Installation Instructions ® H O M E O W N E R S E C T I O N The AromaSteam’s state-of-the-art AromaSteam introduces fragrance into the steam pipe and into your steam shower. MrSteam Aroma is Available in These Five Fragrances: FRAGRANCE PART NO.
Page 178
AromaSteam ® Operation and Installation Instructions H O M E O W N E R S E C T I O N IMPORTANT SAFETY INSTRUCTIONS READ AND FOLLOW ALL INSTRUCTIONS FLAMMABLE LIQUID AND VAPOR • Keep away from heat, sparks, open flames, & hot surfaces protection or face protection •...
Page 179
AromaSteam ® Operation and Installation Instructions H O M E O W N E R S E C T I O N Locating the AromaSteam/Fragrance: 1. Place in a location that allows visual monitoring of the fragrances level. 2. The AromaSteam should not be installed in areas accessible to children. A locked room is strongly recommended (ie: utility room).
Page 180
® Feel Good Inc. ® www.mrsteam.com Products, information and specifications are subject to change without notice. For more information call Sales & Support at 1.800.767.8326 (East Coast) or 1.800.727.8326 (West Coast) for more information.
Page 181
steam ® Technical Specifications Condensation Pan 103867 & 104402 Mr.Steam strongly recommends the use of a condensation pan in the unlikely event of a plumbing leak. Locate the condensation pan on a solid level surface and place the steam generator inside the condensation pan. Insure the steam generator is level.
Page 182
mr . steam ® ® Optional AutoFlush System ____________________________________________________________________________________________________________________________________________ INSTALLATION INSTRUCTIONS BOX CONTENTS: • AutoFlush System Valve with Cord • Installation Instructions. ® ASSEMBLY OF OPTIONAL AUTOFLUSH SYSTEM 3 Pin Connector for AutoFlush AutoFlush Cord Connector AutoFlush Cord Steam Generator AutoFlush Valve End "B"...
Page 183
AutoFlush Shown Fully Assembled INSTALLATION INSTRUCTIONS ® 1. Plumbing to be performed by a qualified plumber and shall be in accordance with applicable National and Local codes. Unit drains by gravity. A drain line that is lower than the AutoFlush assembly must be available.
Page 184
mr . steam ® Optional AutoFlush ® System ____________________________________________________________________________________________________________________________________________ INSTALLATION INSTRUCTIONS BOX CONTENTS: • AutoFlush System Valve with Cord • Installation Instructions. ® ASSEMBLY OF OPTIONAL AUTOFLUSH SYSTEM 3 Pin Connector for AutoFlush AutoFlush Cord Connector AutoFlush Cord Steam Generator AutoFlush Valve Drain Valve Nipple...
Page 185
AutoFlush Shown Fully Assembled INSTALLATION INSTRUCTIONS ® 1. Plumbing to be performed by a qualified plumber and shall be in accordance with applicable national and local codes. Unit drains by gravity. A drain line that is lower than the AutoFlush assembly must be available.
Need help?
Do you have a question about the mr. steam Bliss and is the answer not in the manual?
Questions and answers