Related Manuals for POSIFLEX 4G-100K
Summary of Contents for POSIFLEX 4G-100K
- Page 1 4G-100K 4G LTE Module User Manual Package Contents 4G-100K…........……...(x1) 4G-100K Ver. B0...
- Page 2 Overview of the 4G-100K Antenna Interface Mini-PCIe Interface 4G LTE Antenna SIM Card Slot 12-Pin Connector 5-Pin Connector PCBA for 4G LTE Module Screw Hole...
- Page 3 Installing 4G-100K to TK-32xx Series Kiosk Let the rear side of TK-32xx Series kiosk face to you. The 4G-100K is installed onto the top side of the kiosk. Screw Hole 12-Pin Connector Cable Screw Hole Screw Hole 5-Pin Connector Cable...
- Page 4 Connect the 5-Pin connector cable of the kiosk to the 5-Pin connector of 4G-100K, and connect the 12-Pin connector cable of the kiosk to the 12- Pin connector of 4G-100K. Then fix the 4G-100K to the kiosk with three screws.
- Page 5 Installing 4G-100K to EK Series Kiosk Let the rear side of EK series kiosk face to you. The 4G-100K is installed onto the top side of the kiosk. Screw Hole Screw Hole 5-Pin Connector Cable Screw Hole 12-Pin Connector Cable...
- Page 6 Connect the 5-Pin connector cable of the kiosk to the 5-Pin connector of 4G-100K, and connect the 12-Pin connector cable of the kiosk to the 12- Pin connector of 4G-100K. Then fix the 4G-100K to the kiosk with three screws.
- Page 7 Installing 4G-100K to JK-24xx/27xx Series Kiosk The 4G module and WiFi module can’t be supported at the same time. The WiFi cable is integrated inside the JK series kiosk model, so you have to change the WiFi cable to the 4G cable. Therefore, it is recommended that the installation is taken by professional technician, or contact the service team directly.
- Page 8 (1) Remove the dummy cover by loosening the two screws. (2) Remove the status indicator by loosening the two screws. Unplug the cable and then remove the status indication. Remove the door stopper by loosening two M4 screws...
- Page 9 Remove. Remove the two M4 screws on the hinge brackets.
- Page 10 Remove touch monitor. Remove the touch cable, WiFi cable, and camera cable. WiFi Cable Touch Cable Camera Cable...
- Page 11 Unplug the MF-2100 cable and NR-100 cable. 10. Loosen the two hex nuts to remove the SU-100 module.
- Page 12 11. Loosen the four screws circled as below pictures. 12. Disassemble the front cover and the touch monitor module.
- Page 13 13. Remove the LCD kit by loosening the circled ten hex nuts. 14. (1) Remove the cable tie. (2) Remove the WiFi cable. WiFi Cable...
- Page 14 15. Install the 4G cable and then route the cable with a cable tie. 16. Pass the SI-100 cable and the 4G cable through the display rear bracket like the below picture, and then fix the LCD kit to the display rear bracket with ten hex nuts with washers.
- Page 15 17. Install the front cover to the LCD kit. 18. Fix the four original screws circled as below pictures.
- Page 16 19. Connect the touch cable, WiFi cable, and camera cable. 4G Cable Touch Cable Camera Cable 20. Connect the MF-2100 cable and NR-100 cable.
- Page 17 21. Install the SU-100 with two original hex nuts. 22. Connect the cable to the status indication. 23. Install the status indicator with two original #6/32 screws.
- Page 18 25. Connect the 5-Pin connector cable of the kiosk to the 5-Pin connector od 4G-100K, and connect the 12-Pin connector cable of the kiosk to the 12- Pin connector of 4G-100K. Then fix the 4G-100K to the kiosk with three...
- Page 19 26. Install the touch monitor kit to the main system unit. Make sure the two hinge of the touch monitor kit insert into the two slots.
- Page 20 27. Fix the two hinge brackets with the two M4 screws. 28. Put the door stopper behind the top side of the main chassis like the below picture, and fix it with two M4 screws...
- Page 21 29. Please connect the power cable, display cable, and USB cables refer to the cable routing sticker on the PC box. 30. Installation completed.
- Page 22 Installing 4G-100K to JK-32xx Series Kiosk The 4G module and WiFi module can’t be supported at the same time. The WiFi cable is integrated inside the JK series kiosk model, so you have to change the WiFi cable to the 4G cable. Therefore, it is recommended that the installation is taken by professional technician, or contact the service team directly.
- Page 23 Hold two sides of the monitor and then gently pull it out towards you slowly. Once the crank rod stopper drops down slowly begin to release the touch monitor until it stops. Crank Rod Stopper for Touch Monitor...
- Page 24 Disconnect the cables from the PC box as indicated in the below picture. Lift up the panel while removing it from the stand as the below picture shown.
- Page 25 Remove the green tapes as indicated in the below picture. Loosen the screw as indicated in the below picture while removing the cable clip.
- Page 26 Unplug the cables as indicated in the below picture. (WiFi cable is built-in the system default) WiFi Cable Camera Cable Loosen the two screws as indicated in the below picture.
- Page 27 10. Loosen the four screws as indicated in the picture. 11. Loosen the two screws on the bottom side as indicated in the below picture.
- Page 28 12. Loosen the two screws on the top side as indicated in the below picture, and then remove the front panel frame. 13. Loosen the ten screws with washers and carefully remove the LCD kit.
- Page 29 14. Loosen the screw as indicated in the below picture while removing the cable clip. 15. Remove the cable tie as indicated in the below picture, and then remove the WiFi cable and the SI cable.
- Page 30 16. Put the 4G cable and the SI cable into the cable passage and then use the cable tie to tie the cables like the below picture. 17. Route the cable with the cable clip and then fix it with the original screw.
- Page 31 18. Make the SI cable and the 4G cable pass through the cable passage of the rear cover. Install the LCD kit back to the rear cover, and then fix ten original hex nuts and washers. 19. Make the cables pass through the LCD kit, and then install the front panel frame like the below picture.
- Page 32 20. Fasten the two original screws on the top side as indicated in the below picture. 21. Fasten the two original screws on the bottom side as indicated in the below picture.
- Page 33 22. Fasten the four original hex nuts and washers as indicated in the below picture. 23. Fasten the two original hex nuts and washers as indicated in the below picture.
- Page 34 24. Insert the two USB cables as indicated in the below picture. 4G Cable Camera Cable 25. Route the camera cable with cable clip, and then fix it with one original screw.
- Page 35 26. Please apply green tapes to fix the cables as indicated in the below pictures. 27. Insert the SI cable to the SI-100 device, and then install the device with two original screws as indicated in the below pictures.
- Page 36 28. Connect the 4G cables to the 4G-100K module as indicated in the below picture. 29. Insert your SIM card to the SIM card slot.
- Page 37 30. Connect the 5-Pin connector cable of the kiosk to the 5-Pin connector of 4G-100K, and connect the 12-Pin connector cable of the kiosk to the 12- Pin connector of 4G-100K. Then fix the 4G-100K to the kiosk with three screws.
- Page 38 32. Connect the cables to the PC box as below picture.
- Page 39 34. Installation completed. Installing 4G-100K to HK Series Kiosk Find the dummy cover on the rear side of the HK series kiosk, and then remove the dummy cover by loosening three screws.
- Page 40 Insert your SIM card to the SIM card slot. Pass the USB cable through the cable exit.
- Page 41 EC25 contains several variants, supporting selected bands & countries with full SIM slot (mini-PCIe module) by request. To get more detailed information of 4G LTE module 4G-100K, please contact the service team of Posiflex. ※ The product information and specifications are subject to change without...
Need help?
Do you have a question about the 4G-100K and is the answer not in the manual?
Questions and answers