Crouzet CTP110N-E Series Installation Instruction

CTP110N-E series 88 970 584
Installation and Startup Guide
1
This document covers the installation of CTP 110N-E Series HMI, for the detailed
specifications and operation, please refer to Brochure and Crouzet Touch Soft User Manual.
Handling and Storage:
(1) Storage temperature -20°C/+60°C.
(2) Do not let water penetrate into packaging boxes during their storage and
transportation.
Environmental
(3) Do not store the product in places of high temperature or under direct
Considerations
sunlight
(4) Please also avoid the places of high humidity. Be sure not to expose the
product to condensation, rain or frozen condition
Install Environment:
NEMA Rating CTP110N-E Series HMI is NEMA 4 rated.
CTP110N-E Series HMI has been tested to conform to European CE
Electrical requirements. This means that the circuitry is designed to resist the effects of
Environment electrical noise.
This does not guarantee noise immunity in severe cases. Proper wire routing and
grounding will insure proper operation.
Conform to UKCA.
(1) Make sure that the displays are installed correctly and that the operating
limits are followed. Avoid installing units in environments where severe
mechanical vibration or shocks are present.
(2) Do not operate the unit in areas subject to explosion hazards due to
Environmental
flammable gases, vapors or dusts.
Considerations
(3) Do not install the unit where acid gas, such as SO2 exists.
(4) This device should be mounted in the vertical position and for use on the flat
surface enclosure.
Cleaning
Clean the device using dry cloths. Do not use liquid or spray detergents for
Considerations
cleaning.
IP Rating
IP 66
Protection impairment if used in a manner not specified by the manufacturer.
Warning
Déficit de protection si utilisé d'une manière non spécifiée par le fabricant.
2 Unpacking the Unit
Unpack and check the delivery. If damage is found, notify the supplier.
NOTE: Place the operator panel on a stable surface during installation. Dropping it or
letting it fall may cause damage.
The package includes:
(1) Installation Instruction, 2-sided A4 *1 (2) Human Machine Interface *1 (3) Power Connector *1
(4) Brackets & Screws *1 pack (5) USB Stick Clamp & Tying Strap *1
Installation Instruction
3
Installation Instructions
Use a control box that provides enough stiffness. Secure the operator panel in position, using all the
fastening holes and the provided brackets and screws. Screw Torque: 0.29 ~ 0.44 Nm (For reaching
waterproof effect and preventing the panel from being deformed. Plan for adequate space around
the unit and inside the enclosure, for ventilation and cables. Consider the heat from
other devices inside the enclosure. The ambient temperature around the unit must be 0 ~ 50°C
Minimum required clearances (along the overlay): Top 15 mm / Bottom 50 mm / Sides 80 mm
Maximum panel thickness: 4.5 mm
(A)
(B)
Cutout
Type A(mm) B(mm)
CTP110N-E 260 202
USB Stick Clamp Usage
Combining the USB Stick with the clamp and the tying strap can prevent USB stick from
disconnecting
with HMI when strong vibration is present.
1. Insert the USB connector to the clamp and tie them together with the tying strap.
2. Press the spring and insert the USB stick into HMI.
Power Connections
4
NOTE:
1.Connect positive DC line to the '+' terminal and
the DC ground to the '-' terminal.
2.Please do not connect HMI with PLC and PC
simultaneously to prevent potential difference
from destroying USB ports of HMI and PC.
Power Connector Specifications:
Wire AWG: 24~12
Wiring Conductor Minimum Temperature: 75°C
Screw Torque: 4.5 lbf-in (max.)
Copper conduct only.
Spécifications du connecteur d'alimentation:
AWG de fil: 24 ~ 12
Température minimale du conducteur de câblage: 75°C
Couple de vis: 4.5 lbf-in (max.)
Conducteur en cuivre seulement