NATIONAL MACHINERY NA1298 Instructions

Thank you for purchasing a National Machinery product. Manufactured to a high standard this product will, if used according to these
instructions and properly maintained, give you years of trouble free performance.
IMPORTANT: BEFORE USING THE NA1298 PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS,
WARNINGS AND CAUTIONS. USE THIS PRODUCT CORRECTLY, AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO
SO MAY CAUSE DAMAGE, OR PERSONAL INJURY, AND WILL INVALIDATE THE WARRANTY.
1. SAFETY INSTRUCTIONS
1.1. GENERAL SAFETY
3 Disconnect the drill from the battery unit before changing accessories, servicing or performing any maintenance.
3 Maintain the drill and batteries in good condition. Check moving parts alignment on a regular basis.
3 Replace or repair damaged parts. Use an authorised service agent and recommended parts only. Non authorised parts may be dangerous
and will invalidate the warranty.
3 Ensure the drill is switched off before installing the battery pack.
3 Keep the drill and charger clean for best and safest performance.
3 Remove ill fitting clothing. Remove ties, watches, rings, and other loose jewellery, and contain long hair.
3 Use in adequate working area for its function. Keep area clean, tidy and free from unrelated materials. Ensure there is adequate lighting.
3 Evaluate your working area before using the drill i.e. ceiling, floors and enclosures may contain electrical items or water piping.
3 Ensure battery pack is correctly inserted into the drill handle and snapped in place before attempting to switch drill on.
3 Secure non-stable work piece with a clamp, vice or other adequate holding device.
3 Avoid unintentional starting.
3 Wear approved safety eye protection (standard spectacles are not adequate).
3 Maintain correct balance and footing. Ensure the floor is not slippery and wear non-skid shoes.
3 Be aware that this drill does not need to be plugged into the mains power.
3 Keep chuck direction switch in the locked position until the drill is required for use.
3 Keep children and unauthorised persons away from the working area.
7 DO NOT use the drill where there are flammable liquids, solids or gases such as paint solvents, etc.
7 DO NOT allow children to operate the drill.
7 DO NOT operate the drill if any parts are missing as this may cause failure or possible personal injury.
7 DO NOT hold unsecured work in your hand.
7 DO NOT leave the drill operating whilst unattended.
7 DO NOT carry the tool with your finger on the power switch. Keep chuck direction switch in the locked position.
7 DO NOT force the drill to achieve a task it was not designed to perform.
7 DO NOT operate the drill when you are tired, under the influence of alcohol, drugs or intoxicating medication.
7 DO NOT get the drill or battery charger wet or use in damp or wet locations.
3 Keep drill and charger in their case and store in a safe, dry, childproof area where the temperature will not exceed 104
1.2. BATTERY SAFETY INSTRUCTIONS.
p WARNING! Battery contains nickel-cadmium which is dangerous and must be handled with care to avoid damage, fire, corrosion or personal injury.
3 Charge battery prior to its first use. The battery pack will have been shipped in a low charge state.
3 Use the provided charger only to charge the drill battery.
7 DO NOT charge battery when room temperature is below 50
7 DO NOT attempt recharging the battery by means of an engine generator or a DC power source.
7 DO NOT short-circuit the battery by touching both terminals with a metal object, or your fingers etc.
7 DO NOT store the battery (and drill) in locations where the temperature may exceed 104
heaters, or metal buildings in summer.
p WARNING! dispose of spent batteries correctly as they contain nickel-cadmium. DANGER! DO NOT attempt to disassemble the battery
pack. For safety and environmental reasons DO NOT discard in domestic waste, or by burning. ONLY discard or recycle according to local
waste authority regulations.
p WARNING! DO NOT allow a leaking battery to contact your person. If you come into contact with battery liquid take the following
immediate action:
1.3. ELECTRICAL SAFETY.
REGARDING DIRECT MAINS POWER USE WITH THE CHARGING BASE AND TRANSFORMER PLUG ONLY .
p WARNING! It is the user’s responsibility to read, understand and comply with the following electrical instructions:
You must ensure the risk of electric shock is minimised by the installation of appropriate safety devices. An RCCB (Residual Current Circuit
Breaker) should be incorporated in the main distribution board. We also recommend that an RCD You must also read and understand the follow-
ing instructions concerning electrical safety.
1.3.1. The Electricity At Work Act 1989 requires all portable electrical appliances, if used on a business premises, to be tested by
a qualified Electrician at least once a year by using a Portable Appliance Tester (PAT).
1.3.2. The Health & Safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of the appliance,
and the safety of the appliance operator. If in any doubt about electrical safety, contact a qualified electrician.
1.3.3. You must ensure you:
Inspect the transformer plug, wire, adaptor, and the charger base for wear and damage to ensure items are safe before
connecting to the mains power supply. If worn or damaged DO NOT use, immediately replace, or contact a qualified Electrician
3
Check cables are always protected against short circuit and overload.
Important: Check the voltage marked on the transformer plug is the same as the electrical power supply to be used.
3
Uncoiled the power cable between the transformer and the charger before use.
3
3
p a) Skin contact: Wash immediately with soap and water, then wash flesh in either lemon juice or vinegar.
p b) Eye contact: Wash with a strong solution of boric acid, and seek immediate medical attention.
Instructions For:
12 C
V ORDLESS
M
odel No:
F (10 C) or above 104 F (40
O O O
O
P
NA1298
OWER
C).
O
F (40 C ) such as outside sheds, above
O
T
OOL
F (40 C).
O O
NA1298 - 1022 - (NO3) - 070199