Summary of Contents for GAINWISE TECHNOLOGY SS1806-4G01EC-H
- Page 1 GAINWISE TECHNOLOGY MANUAL 4G GATE OPENER SS1806-4G01EC-H 2 outputs, 3 inputs Please read these instructions completely before use it 4G Gate Opener 1/17 Revision V1.3B, Jan 2020...
-
Page 2: Table Of Contents
TABLE OF CONTENTS 1. SAFETY PRECAUTIONS .................... 3 2. BRIEF INTRODUCTION .................... 3 3. PRODUCT FEATURES ....................4 4. STANDARD PACKING LIST ..................4 5. INSTALLATION ......................4 5.1 SIM card installation.................... 4 5.2 Antenna Connection ..................... 5 5.3 Wiring Diagram ....................5 5.4 Power Supply ....................... -
Page 3: Safety Precautions
Thank you for purchasing 4G Gate Opener. Please read this manual carefully before using. Be sure to keep this manual for future reference in case of any problems happen. 1. SAFTY PRECAUTIONS Unplug the power adapter before cleaning. Do not use liquid cleaners or aerosol Cleaners. Use a damp cloth for cleaning. -
Page 4: Product Features
3. Product Features: Up to 1150 users for access control by caller ID automatic number recognition.. Switches relay with free call from mobile phone Secure password protected Programming via simple SMS commands or App 3 inputs for sensors or switches Send SMS notification when a short circuit exists on inputs Check Log history via E-mail or SMS Ideal for remote control of automatic gates, barriers, doors, central heating systems, security alarm,... -
Page 5: Antenna Connection
Fig1 5.2 ANTENNA CONNECTION Ensure that there is good network reception at the location where it wil be installled. If you use a 3 meters antenna install it as high as possible on the top of the pillar for best possilbe reception. -
Page 6: Power Supply
Fig3 5.4 POWER SUPPLY The 4G Gate Opener is designed to work with power supplies 12V~24V AC/DC. The power supply should be capable of supplying a constant current of no less than 1amp. After a final check of wiring switch on the power. allow 20~30 seconds for the unit to boot up and detect the network. -
Page 7: Led Indicators
6. LED INDICATORS Fig4 LED Status Definition Number Solid Flash Trigger input 3 Input 3 active Standby In triggering setup time & Sending SMS (24+Time#) Input 2 active In triggering setup time Trigger input 2 Standby & Sending SMS (17+Time#) Input 1 active In triggering setup time Trigger input 1... -
Page 8: Operation
7. OPERATION Programming of the telephone numbers in and whenever the unit receives a call will recognize an authorized telephone number calling it and will then reject the call without answering (so there will be no charge) and open the gate or door. The relay can also be temporarily or permanently switched on or off by sending SMS or dialing in. -
Page 9: Programming By Text Message
Note: *programming dialing in can’t be used from telephones which are already programmed to open the door when they dial the 4G Gate Opener. * If the number is programmed to open the door but you still would like to use the same number to dial in for programming, then you can disable Caller ID display (withhold the number) on the mobile. -
Page 10: Administrator Number
9. ADMINISTRATOR NUMBER Once the administrator number is stored, the unit will only accept programming from this number and only via SMS programming. Example: Program a mobile number as an administrator number via SMS Mobile number: 0865682554 Command to use *12*1234#74 [Admin number]# SMS format *12*1234#740865682554# To delete the Admin number *12*1234#74*# 10. -
Page 11: Check All Logged Door Access Events Via E-Mail Or Sms
13. CHECK ALL LOGGED DOOR ACCESS EVENTS VIA E-MAIL OR SMS This system allows you to check the history of all logged door access events via E-Mail or SMS. There is a list of commands you need and examples to guide you on the settings for this feature. Please setup following required parameters and commands before you can use it. - Page 12 Function SMS command codes E-mail subject setting *43*1234# e-mail subject# Command code Example: Immediately sending request logged *44*1234# events via email or SMS SMS reply: successful or failed *4[N]*1234# ( reply GPRS parameters) Check parameters setting N=1 ( reply e-mail parameters) N=2 ( reply recipient &...
- Page 13 2. Via-SMS There are 3 programming codes you will need to make this feature work You can program many different user command codes in a single text message with SMS command format. *12*1234 # [command Code1] # [command Code 2] # [command Code3] #..Example: Mobile number for receiving logged events 0907967223 SIM phone number held within the opener 0948778458...
-
Page 14: User Commands
14. USER COMMANDS You can program many different user command codes in a single text message with SMS command format. *12*1234 # [command Code1] # [command Code 2] # [command Code3] #..Command Description settings Default 01 [new password]# Change password of Programming password:4 ~6digits 1234 Mode... - Page 15 Command Description settings Default 21[mode]# Set Input 2 mode Mode= 0, 1, 2 or 3 0 = Disable , 1 = Trigger 2 = Egress 1, 3 = Egress2 27 [mode]# Set Input 3 mode Mode= 0 or 1 0 = Disable , 1 = Trigger 28+IN*time start+ time Set time duration ( enable inputs ) 1, 2 or 3...
-
Page 16: Specifications
Command Description settings Default 75[N]*# Delete mobile number of alarm N=1~3(sequence of phone contact when inputs are triggered. number) N= 0 or 1 0= disable 1= enable SMS confirmation of 871+N# SMS messages: relay switching Relay 1 trigger, relay 2 trigger Relay 1 hold, relay 2 hold Relay 1 release, relay 2 release 999#... -
Page 17: Quick Programming Via Sms And Operation
You can dial in or send SMS password code to the device to control relay. *71*5678#：Trigger relay 1 *72*5678#：Hold relay1 *73*5678#：Release relay1 *74*5678#：Trigger relay 2 *75*5678#：Hold relay 2 *76*5678#：Release relay 2 Gainwise Technology Co., Ltd. 4G Gate Opener 17/17 Revision V1.3B, Jan 2020...
Need help?
Do you have a question about the SS1806-4G01EC-H and is the answer not in the manual?
Questions and answers