Advertisement
Quick Links
Getting Started
Getting Started
Ensure all parts are in good state and match with the parts list.
Remove all protective materials and place parts on a non-abrasive
surface to avoid scratching.
Care & Maintenance
- Wash screen house with a mild solution of soap and water; rinse
thoroughly. Dry completely under the sun.
- When not in use, take down and store awaye to avoid
damage and fading from exposure to the elements.
- This screen house came with 12 month quality warranty. Fading
due to regular use is not covered.
- Always put the tent away in dry status. Never store it still wet or
damp, as mildew and other problems might occur.
Caution
Read all instructions before set-up. Failure to comply with
instructions may result in faulty assembly and potential injury.
During periods of excessive wind, do not assemble or
disassemble the product if already in use to prevent damage.
Storage
When storing for long periods of time, always make sure the tent is
completely dry and free of any caked-on dirt or debris. Be sure to
store it in a cool, dry place away from rodents and other pests.
WARNING :
KEEP AWAY ALL FLAME AND HEAT SOURCES FROM THIS
SCREEN HOUSE. This tent meets the flammability
requirements of CPAI-84. But may burn if left in continuous
contact with any flame source. The application of any foreign
substance to the tent fabric may render the flame-resistant
properties ineffective.
1
Advertisement
Summary of Contents for EVER ADVANCED B08LK57V6W
- Page 1 Getting Started Getting Started Ensure all parts are in good state and match with the parts list. Remove all protective materials and place parts on a non-abrasive surface to avoid scratching. Care & Maintenance - Wash screen house with a mild solution of soap and water; rinse thoroughly.
-
Page 2: Parts List
Parts List Parts List Picture Description Screen House Fiberglass Poles Carry Bag Tie-down Ropes with adjustment glider Stakes... -
Page 3: Before You Begin
Set UP BEFORE YOU BEGIN -Locate a level location to set up your tent and clear away any debris and sharp objects. -In extremely windy conditions, find wind block for easier setup. -Avoid setting up the tent under any overhead obstructions for safety reasons, such as falling objects or lightning strikes in the case of inclement weather. - Page 4 Set UP FIG. 2 outer Rooftop Pull out X5 STEP 3: Reach for the center webbing and pull back to pop open the side wall. Repeat for 5 times to pop open all side walls .See Fig 2. Gently pull outward until the hub pops into the open position.
- Page 5 Set UP FIG. 3 STEP 4: At this point the tent should be standing on its own, with the rooftop unset up. Enter the screenhouse through the front zip door. Find the center hub and push upward until the rooftop pops into fully opened positioned.See Fig. 3. NOTE: Use caution during this step to avoid potential harm when poping into place.
- Page 6 Set UP FIG. 5 Peg in Slide to adjust ADJUSTMENT SLIDER STEP 6: Outside of the screen house , begin anchoring the ground skirt into place with the provided Stakes (E) and Tie-Down Ropes (D). Use the adjustment sliders to get the correct tension for the rope.
- Page 7 Take Down Disassembly FIG. 7 POLE STEP 1A: Undo the hook and loop tabs around the Fiberglass Poles (B) the n remove them from the interior sleeves, at the corners of the front door. See Fig. 7. STEP 1B: Remove the Stakes (E) and relax the Tie-Down Ropes (D) from outside of the tent.
- Page 8 Take Down FIG. 8 Out rooftop STEP 2: Walk inside the tent, grab the webbing loop hanging from the center rooftop hub and pull down until the tension releases and the roof drops down. See Fig. 8. NOTE: Use caution to avoid hitting your head on the poles as they come down.
- Page 9 Take Down FIG. 9 Inner rooftop STEP 4: At this point, the tent will be flat on the ground. Gather the corners of each side wall and fold in. Be watchful of entangled poles and don’t force the tent while folding it.
Need help?
Do you have a question about the B08LK57V6W and is the answer not in the manual?
Questions and answers