Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for MAKINEX CG-2050
- Page 1 Concrete Grinder CG-2050 OPERATOR’S MANUAL Rev 0524...
-
Page 2: Table Of Contents
TABLE OF CONTENTS ................1 ................................1 INTRODUCTION ..........................3 DISCLAIMER ............................ 3 ABOUT THIS MANUAL ........................4 SAFETY INFORMATION ........................5 PRODUCT DESCRIPTION AND SPECIFICATION ..................6 INSTRUCTIONS FOR USE ........................7 STEP 1 – CONSIDERATIONS FOR USE ....................7 STEP 2 –... -
Page 3: Introduction
Keep this manual or a copy of it with the machine. If you lose this manual or need an additional copy, please contact MAKINEX. This machine is designed and built with user safety in mind; however, it can present hazards if improperly operated and serviced. If there are any questions regarding operating or servicing of this machine, please contact MAKINEX. -
Page 4: About This Manual
PROHIBITED These safety warnings do not eliminate all possible hazards that could occur therefore it is essential to use common sense and to strictly follow any instructions to prevent accidents. MAKINEX CG-2050 Operator’s Manual Rev0524 Page 4 of 17... -
Page 5: Safety Information
Ensure you read all information contained in this manual before using the CG- READ 2050. CAREFULLY Ensure you read the User Manual and safety instructions for the CG-2050 and other components that are part of this unit. READ See Appendix for more information. -
Page 6: Product Description And Specification
PRODUCT DESCRIPTION AND SPECIFICATION CG-2050 Concrete Grinder and Trolley is a robust tool is your go-to for grinding, polishing, and finishing concrete surfaces, offering exceptional adaptability. Its ergonomic lightweight frame excels in leveling floors and edge grinding, delivering 2-in-1 capabilities. -
Page 7: Instructions For Use
INSTRUCTIONS FOR USE NEVER operate the CG-2050 without wearing the appropriate personal protective equipment (PPE) including appropriate footwear. Assess the surrounding area for hazards. Ensure that any loose clothing and WARNING long hair is firmly tied back. ALWAYS seek appropriate First Aid if Injury, Poisoning or Irritation occurs due to contact with Materials and Substances. -
Page 8: Step 2 - Spare Part List
STEP 2 – SPARE PART LIST Cover plate kit with magnet Brush for dust cover Makinex Vac Adapter M38-F42 Carbon Brush MAKINEX CG-2050 Operator’s Manual Rev0524 Page 8 of 17... -
Page 9: Step 3 - Operating Instrutions
STEP 3 – OPERATING INSTRUTIONS Step 1：Connect the Vac adapter to the internal dust outlet before connecting external suction pipe to Vac adapter, secure and ensure they are completely connected. MAKINEX CG-2050 Operator’s Manual Rev0524 Page 9 of 17... - Page 10 (do not loosen your hands). The machine will proceed to be ready for polishing work as soon as it becomes stable. For different work demands, adjust the rotate speed by twirling the speed control knob using the left-hand finger. The machine must be horizontal while in working process. MAKINEX CG-2050 Operator’s Manual Rev0524 Page 10 of 17...
- Page 11 30 seconds. Then Press the motor power button after the dust inside of the anti-dust cover has been well collected and cleaned. MAKINEX CG-2050 Operator’s Manual Rev0524 Page 11 of 17...
- Page 12 Hexagonal wrench to the lock screw. (3) Rotate these both wrenches towards opposite directions. (4) Take the lock screw off then install a new cup wheel by repeating above steps, you will achieve it easily. MAKINEX CG-2050 Operator’s Manual Rev0524 Page 12 of 17...
-
Page 13: Limited Warranty
MAKINEX warrants each new mixer to be free from defects in material and workmanship under normal domestic and industrial use and service for the period specified below, conditional to the limitations and exclusions printed on this page. This warranty applies only to new MAKINEX mixer distributed by us and by our authorised MAKINEX dealers. - Page 14 All warranties will be carried out by MAKINEX authorised staff or appointed agents at a premise to be determined by the Manufacturer. It is the responsibility (and cost) of MAKINEX or our appointed agent to return the machine to be repaired •...
-
Page 15: Contact Information
CONTACT INFORMATION For sales, service, warranty and parts for all MAKINEX products; please refer below. SALES, SERVICE, SPARE PARTS & WARRANTY SALES TEL 1300 795 953 or +61 2 9460 8071 WEB www.makinex.com.au AUSTRALIA SERVICE, SPARE PARTS & WARRANTY EMAIL service@makinex.com.au... -
Page 16: Risk Assessment
RISK ASSESSMENT MAKINEX CG-2050 Operator’s Manual Rev0524 Page 16 of 17... - Page 17 MAKINEX CG-2050 Operator’s Manual Rev0524 Page 17 of 17...
Need help?
Do you have a question about the CG-2050 and is the answer not in the manual?
Questions and answers