Related Manuals for KALI AUDIO Project Watts WS-12 V2
Summary of Contents for KALI AUDIO Project Watts WS-12 V2
- Page 1 Project Watts WS-12 V2 Studio/Live Subwoofer User’s Guide Kali Audio WS-12 V2 User’s Guide...
-
Page 2: Table Of Contents
Table of Contents IMPORTANT SAFETY INFORMATION…………………....……..…………….3 Informations de Sécurité Importantes..............5 ABOUT YOUR SUBWOOFER.…..…..………........………………….7 FULL SPECIFICATIONS…………………………….…...……......…………………9 INPUTS AND CONTROLS………………………..……...………....……………10 DIP SWITCHES....................13 FIRST TIME SETUP…………………………………………......…...…………...17 TROUBLESHOOTING………………………………………......…...……………...18 LIMITED WARRANTY…………………………………………………..…......……19 Kali Audio WS-12 V2 User’s Guide... -
Page 3: Important Safety Information
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDI- TIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE AND (2) THIS DEVICE MUST ACCEPT ANY INTER- FERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. Kali Audio WS-12 V2 User’s Guide... - Page 4 The exclamation point within an equilateral triangle is intended to alert the user of the presence of important operation and maintaining (servicing) instructions in the literature accompanying the appliance. Kali Audio WS-12 V2 User’s Guide...
-
Page 5: Informations De Sécurité Importantes
Lorsqu’un chariot est utilisé, soyez prudent lorsque vous déplacez la com- binaison chariot / appareil vers éviter les blessures par renversement. 16. Débranchez cet appareil pendant les orages ou lorsqu’il n’est pas utilisé pendant de longues péri- odes. Kali Audio WS-12 V2 User’s Guide... - Page 6 électrique pour les personnes. Le point d’exclamation dans un triangle équilatéral est destiné à alerter l’utilisateur de la présence d’instructions importantes de fonctionnement et de maintenance (entretien) dans la documentation accompagnant l’ap- pareil. Kali Audio WS-12 V2 User’s Guide...
-
Page 7: About Your Subwoofer
WS-12s will be sufficient in most immersive systems using Kali’s full-range speakers. The WS-12 V2 will be an excellent companion to both Kali Audio speakers, and other speakers and studio monitors that are designed for near-to-mid field monitoring. - Page 8 On the top of the sub, there is an M20 threaded pole cup to accept speaker poles for mounting PA speakers above the subwoofer. Kali Audio WS-12 V2 User’s Guide...
-
Page 9: Full Specifications
Pass-through signal-to-noise ratio: >115 dB Other Inputs/Outputs: 1/4-Inch Footswitch for Sub Bypass Enclosure: Front Ported Pole Cup: M20 Threaded Height 19.2 Inches (48.8cm) Width: 17.2 Inches (43.7cm) Depth: 20.5 Inches (52.1cm) Weight: 58 lbs (27 kg) Kali Audio WS-12 V2 User’s Guide... -
Page 10: Inputs And Controls
The signal from the subwoofer will be high-passed according to the crossover set with dip switches 1-4. If using more than 2 full-range speakers, it is recommended to use an exter- nal processor and crossover. Kali Audio WS-12 V2 User’s Guide... - Page 11 110V-230V switch (10) is set to the appropriate setting for your location. Most areas in North America use 110V power, and most areas in Europe use 220V power. If you are unsure of the voltage in your location, search “Local Voltage (Name of your country.)” Kali Audio WS-12 V2 User’s Guide...
- Page 12 Full range speakers connected to the subwoofer will behave as if they are not connected to the subwoofer. Solid Orange: The WS-12 is on, but in standby mode. To wake the subwoofer up, play signal through it. Kali Audio WS-12 V2 User’s Guide...
-
Page 13: Dip Switches
XLR outputs. Crossovers can be set every 5 Hz between 50 Hz and 110 For all Kali Audio speakers, and most common studio monitors, Kali recommends using the 80 Hz crossover. (DIP Switches 2 and 3 UP) For other speakers, multiply the speaker’s lower frequency response spec by 2, and then round up to... - Page 14 1 kHz unless the signal you send to it is low-passed. This position will not send signal through the subwoofer’s XLR outputs. Switch 1: DOWN Switch 2: UP Switch 3: UP Switch 4: UP Kali Audio WS-12 V2 User’s Guide...
- Page 15 EQ Wizard (REW) to test the polarity of your subwoofer. Instructions for doing so are readily available with a quick internet search. Position 1: 0° Position 2: 180° Switch 7: DOWN Switch 7: UP Kali Audio WS-12 V2 User’s Guide...
- Page 16 The subwoofer will come back online once it receives signal. If this operation is not desired, turn switch 8 up to disable standby mode. Position 1: Standby On Position 2: Standby Off Switch 9: DOWN Switch 9: UP Kali Audio WS-12 V2 User’s Guide...
-
Page 17: First Time Setup
8. Use the volume knob on the subwoofer to adjust its level relative to the main speakers. Enjoy your new subwoofer! Kali Audio WS-12 V2 User’s Guide... -
Page 18: Troubleshooting
• If the subwoofer plays after being turned off and on again, reduce the output level of the sub, and make sure it is in a cool, well-ventilated area so that it does not overheat. If none of the above solves your problem, contact your dealer to initiate a return. Kali Audio WS-12 V2 User’s Guide... -
Page 19: Limited Warranty
Damage resulting from an unauthorized person servicing the product. Damage resulting from the product being left plugged in during an electrical storm. The warranty applies only in the United States. International Customers should contact their dealer about their warranty policy. Kali Audio WS-12 V2 User’s Guide...
Need help?
Do you have a question about the Project Watts WS-12 V2 and is the answer not in the manual?
Questions and answers