Related Manuals for SkoFlo Industries BPR15000D
Summary of Contents for SkoFlo Industries BPR15000D
- Page 1 Industries Surface, Back Pressure Regulator 15000 psi BPR15000D Operations and Maintenance Manual Pioneering an Industry DOC-04194 Rev B...
-
Page 2: Table Of Contents
Table 4 – Stem Kit Number Guide ..........5 Troubleshooting .................. 9 Table 5 – Maintenance Tool Requirements ......5 Appendix A – A Typical Chemical Injection System .... 10 Appendix B – BPR15000D GA and BOM Drawing ....11 Operations and Maintenance Instructions... -
Page 3: About Skoflo
BPRs provide a constant pressure to the system with continuous spill-off to the chemical tank that is Gallons Per Day independent of the flow rate. The BPR15000D has a Kg/m Kilograms per Meter maximum operating pressure of 15,000psi and supports Liters Per Hour flow ranges of 0 - 800 GPD and 100 - 2000 GPD. -
Page 4: Storage
! NOTICE IT IS RECOMMENDED TO STORE THE ASSEMBLIES IN THE SHIPPING CRATE, IF POSSIBLE. The BPR15000D should be stored in a shelter and be protected from moisture and particulates. Storage temperatures shall be between –50°F and 158°F (–45°C and 70°C). -
Page 5: Operation Notes And Warnings
! NOTICE − 1/2” FKO IF ANY ABNORMALITIES ARE FOUND THROUGHOUT THE If the BPR15000D uses FKO hub connections, the hubs are MAINTENANCE, PLEASE REPORT TO THE RESPECTIVE shipped separately from the valve and will need to be ENGINEERS. installed in the inlet and outlet ports prior to use. -
Page 6: Table 3 - Seal Kit Number Guide
Surface, Back Pressure Regulator BPR15000D Table 5 – Maintenance Tool Requirements Tools and Parts Quantity Table 3 – Seal Kit Number Guide Brass Pick CODE WORKING PRESSURE Brass Rod (3.5mm diameter) 15 KSI Dynatex Anti-Seize Lubricating Compound (or 10 KSI... -
Page 7: Replacing Base O-Ring
Surface, Back Pressure Regulator BPR15000D 5. Replacing Base O-Ring 6.4 Unscrew the pin holder from the piston. Be careful not to drop the pin (20200) and coil 5/8” Wrench spring (71006349) inside. – 6.5 Remove the old piston cup seal and pin. -
Page 8: Figure 5 - O-Ring Tool
Surface, Back Pressure Regulator BPR15000D 7.3 Place a 12mm socket over the seat retainer and rotate counter-clockwise until you can withdraw the old stem assembly from the body. See 12mm Socket, Socket Extension Figure 4. – ! NOTICE USE CARE WHEN REMOVING THE STEM TO AVOID DAMAGING THE INTERNAL SEALING SURFACES OF THE BPR. -
Page 9: Bpr Reassembly
Surface, Back Pressure Regulator BPR15000D 7.25 Apply generous coating of lithium grease to stem threads. 7.26 Apply O-Ring lube to stem sealing surface. See Figure 8 Figure 8 – Stem Sealing Surface 7.27 Pushing on the seat retainer, insert stem fully into body. -
Page 10: Troubleshooting
Surface, Back Pressure Regulator BPR15000D ROUBLESHOOTING Operations and Maintenance Instructions... -
Page 11: Appendix A - A Typical Chemical Injection System
Surface, Back Pressure Regulator BPR15000D A – A T PPENDIX YPICAL HEMICAL NJECTION YSTEM NOTES Any number of injection points can be served by a single pump and header system. The only limitation is the flow capability of the pump. -
Page 12: Appendixb - Bpr15000D Ga And Bom Drawing
Surface, Back Pressure Regulator BPR15000D B – BPR15000D GA BOM D PPENDIX RAWING Operations and Maintenance Instructions... - Page 13 Surface, Back Pressure Regulator BPR15000D Operations and Maintenance Instructions...
- Page 14 Surface, Back Pressure Regulator BPR15000D Operations and Maintenance Instructions...
- Page 15 SkoFlo Industries 14241 NE 200 Street Woodinville, WA 98072 USA Tel 1-425-485-7816 Fax 1-425-368-1696 www.SkoFlo.com Operations and Maintenance Instructions DOC-04194 Rev B...
Need help?
Do you have a question about the BPR15000D and is the answer not in the manual?
Questions and answers