Do you have a question about the Switch 2.0 Height Adjustable Single Desk and is the answer not in the manual?
Questions and answers
Subscribe to Our Youtube Channel
Summary of Contents for Hawk Switch 2.0 Height Adjustable Single Desk
Page 1
Switch 2.0 Height Adjustable Single Desk User Guide MAKE SURE NO OBSTACLES ARE IN THE DESK′SPATHAND ALLCORDSAREOFAPPROPRIATELENGTHFORDESK TRAVEL.FAILURETOCOMPLYWITHOROBSERVEALL CAUTION ASSEMBLY,SAFETY,ANDOPERATIONINSTRUCTIONSAND WARNINGSREGARDINGTHEUSEOFTHISPRODUCTMAY RESULTINSERIOUSPROPERTYDAMAGEORBODILYINJURY. IMPORTANT Any user or installer of desk base must study this manual carefully. If this desk is sold,please provide the manual to the buyer.
CAUTION: SAFETY AND WARNINGS ·Inappropriate use of this product may cause property or bodily injury. Make sure that children, pets, etc. stay away from the product when the desk is in operation. ·Check the surroundings on all sides before using the desk. Make sure the desk does not touch the wall.
SETUP AND INSTALLATION Once the desk has been assembled, adjust the feet so that the desk is level and does not shift its position. After this, connect the desk to the 110v or 240v outlet and the desk is ready for use. Check that no cables can get jammed.
PARTS LIST Tools Required Tapemeasure Wrench(included) Philips Head Screwdriver Power Drill Components Side Bracket *2 Lifting Column Lifting Column Base Frame Leveling Studs * 4 Handset * 1 Wires * 1 Hanger otor Rod Adapter Hardware Qty 4 Qty 4 Qty 6 Qty 8 Qty 2...
Page 5
ASSEMBLY INSTRUCTIONS Pull out the frame Lay out all components and hardware to ensure that you have all the parts. Lay the out flat on the floor, slide the frame out evenly from both sides. frame Attach legs to frame Align the to the lifting column, Insert the M6×12 mm screws(C),and tighten it.
Page 6
Attach foot Attach leveling studs to the foot. Align the foot with the lift column, and insert four M6×35 mm(D) into the holes under the feet,tighten it. Repeat for the other side. Allen Key D×8 lock screw Avoid over-tightening the screws to damage the product. Attach motor rod ATTENTION PLEASE...
Page 7
& Adapter Attach side bracket Line up the two holes on the side bracket with the frame Insert two M6×8 mm screws(C)and tighten it. Attach the washers on the side bracket. Repeat for the other side. First, stick Glue Pad(I) onto adapter(9),Insert hanger(6) into the crossbar and put the adapter (9) in the hanger(6).
Page 8
Handset Attach Attach the Handset(8) to the tabletop plate with M3.5×14mm(E) screws. E×2 Avoid over-tightening the screws to damage the product. Attach Connect Cables Connect the line pulled from lifting column A to Handset(10) . Connect the outgoing lines from the Handset (10) to the Adapter(9). Connect power cable (11) to Adapter(9) AC port.
Page 9
Put desk Upright and Connect Power Cord to the Power Supply With the desk at its lowest height,turn the assembled desk right-side up with the help of at least two people. Plug the Power Cord(9)into a 110-240v outlet. NOTE: Grab the desk Frame (not the desktop and turn the desk right-side up. Use at lease two people.
Page 12
Error messages on the handset 's display Displayed error Possible cause Solution message H O T High power temperature Wait for 18mins or unplug the desk for 15seconds then plug it again There is an internal error in the Unlock the desk, keep pressing the L O C up and down button together till the control unit.
Need help?
Do you have a question about the Switch 2.0 Height Adjustable Single Desk and is the answer not in the manual?
Questions and answers