1. Manuals
  2. Brands
  3. STL Manuals
  4. Touch terminals
  5. OptoBlaze Multiport Service Terminal
  6. Installation manual

STL OptoBlaze Multiport Service Terminal Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Installation Guide
STL OptoBlaze
Multiport Service Terminal (MST)
This guide shows the installation of STL MST for different installation techniques.
Pole
Under Ground
Aerial

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the OptoBlaze Multiport Service Terminal and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for STL OptoBlaze Multiport Service Terminal

  • Page 1 Installation Guide STL OptoBlaze Multiport Service Terminal (MST) This guide shows the installation of STL MST for different installation techniques. Pole Under Ground Aerial...

  • Page 2: Table Of Contents

    INSTALLATION USING X-BOARD POLE MOUNTING USING STAND-OFF BRACKETS POLE MOUNTING WITHOUT STAND-OFF BRACKETS (DIRECT) BACK-TO-BACK POLE MOUNT UNDERGROUND INSTALLATION WITH MOBRA ARM AERIAL INSTALLATION WITH UNIVERSAL MOUNTING BRACKET MST SST CABLE TAIL PREPARATION RECOMMENDED TOOLS FOR STL’S MST SST CABLES 10. .

  • Page 3: Introduction

    INSTALLATION INSTRUCTION OptoBlaze - Multiport Service Terminal (MST) 1. INTRODUCTION The OptoBlaze MST is an essential component within the access network, facilitating the rapid connection between the Fiber Distribution Hub and subscribers. When customers opt for FTTH service, the OptoBlaze Terminal serves as the crucial link, connecting the drop cable to their residences.

  • Page 4: Installation Using X-Board

    OptoBlaze - Multiport Service Terminal (MST) 3. INSTALLATION USING X-BOARD All STL MSTs are designed to be installed using the X-Board. Please be aware that not using the X-Board may cause damage to the MST and its cable. 1. Release the MST head from the tail coil taking care not to allow the head to drop unsupported.

  • Page 5: Pole Mounting Using Stand-Off Brackets

    4. POLE MOUNTING USING STAND-OFF BRACKETS 1. To mount the STL onto a pole directly using the stand-off brackets found in the accessories box that comes with the MST. These are attached by pushing them onto the back of the MST body top and bottom as per the images below.

  • Page 6: Pole Mounting Without Stand-Off Brackets (Direct)

    5. POLE MOUNTING WITHOUT STAND-OFF BRACKETS (DIRECT) 1. To mount the STL onto a pole directly without using the stand-off brackets, you must present the MST to the pole and screw in the bottom fixing screw leaving 10-12mm of the screw sticking out (Fig 1).

  • Page 7: Back-To-Back Pole Mount

    OptoBlaze - Multiport Service Terminal (MST) 6. BACK-TO-BACK POLE MOUNT 1. Mount the STL MST without the stand mounts directly to the back-to-back mount. Screw the bottom fixing part way (10-12mm) onto the back-to-back mount and slide on the MST using the bottom lug via the bottom fixing.

  • Page 8: Underground Installation With Mobra Arm

    7. UNDERGROUND INSTALLATION WITH MOBRA ARM 1. The STL MST is mounted on the mobra arm with fixings found in the accessories pack that comes with the MST. Remove the screws and mount the Zebedee springs into the mobra arm (Fig 1, 2 & 3).

  • Page 9: Aerial Installation With Universal Mounting Bracket

    INSTALLATION INSTRUCTION OptoBlaze - Multiport Service Terminal (MST) 8. AERIAL INSTALLATION WITH UNVERSAL MOUNTING BRACKET 8.1. Installation Procedure for 6, 8, and 12 port MST 1. Add mounting bolt near cable entry port. 2. Add mounting bolt at opposite end. 3.
  • Page 10 INSTALLATION INSTRUCTION OptoBlaze - Multiport Service Terminal (MST) 5. Using a standard can wrench, add locking nuts 6. Using a standard can wrench, affix assembly to to secure bracket to terminal. the strand. Note: Secure bolts using 20 in-lb. (2.3 N-m) of torque (maximum application using can wrench) 8.2.

  • Page 11: Mst Sst Cable Tail Preparation

    9. MST SST CABLE TAIL PREPARATION The following is the recommended method required to prepare the SST tail cable on the STL MST. Once you have cut the required length of cut for your installation mark from the cut end approximate- ly 1.5m (Fig 1 &...
  • Page 12 INSTALLATION INSTRUCTION OptoBlaze - Multiport Service Terminal (MST) Remove and cut the outer sheath, without cutting the ARP strength members, leaving approx 2cm of the sheath. at the butt end of the cable (Fig 1). The fiber is in the gel-filled loose tube. Using the correctly adjusted loose tube cutter, start removing the loose tube at approximately 25-30cm pieces at a time.

  • Page 13: Recommended Tools For Stl's Mst Sst Cables

    STL be liable for any incidental, indirect or consequential damages arising out of sale, resale, use or misuse of the product. Users of STL products should make their own evaluation to determine the suitability of such each product for the specific application.

Table of Contents